Is the S9 the best one right now? I would like to own some mining gear one day. Like before the banks, Google, etc., start mining.
Yes the S9 currently has the highest hashrate and best efficiency but make sure you can run it on you wall and are willing to deal with the noise and heat output. 
Topic: 10x S9 all showing very slow at the pool (Read 3271 times)
Is the S9 the best one right now? I would like to own some mining gear one day. Like before the banks, Google, etc., start mining.
Looks like I have the same issue with my new Antminer S9-B2 on GHASH-IO. It shows Alive and will GetWork but all work is Rejected. The Accepted on the Miner Status Page stays at zero. The Miner works fine on Eligius and AntPool. If I put GHASH.IO as the primary pool the miner keeps trying to fall back to GHASH.IO and the hash rate is pretty bad on the other pool so it just eats electricity with low earnings.
wrong screen shot. and do try a better pool kano.is is known to work well with s-9's
His picture shows correct reason.
S9 do not use Cgminer 4.8.0 Instead is BMminer Version 1.0.0
That is the right reason. You can only use some BTC miningpools and not mine any Altcoins.
legendary
Activity: 1848
Merit: 1166
My AR-15 ID's itself as a toaster. Want breakfast?
its probably because of "BMminer" instead of CGminer, I'm unable to mine alt-coins with my s9 nor can i rent it out.
getting only hw errors
getting only hw errors
You realize S9 only mines bitcoins (and other few SHA256 coins)? When you say alt-coins, I assume you mean Scrypt and other protocol alt-coins.
No, hes speaking of the plethora of other SHA256 based altcoins....
its probably because of "BMminer" instead of CGminer, I'm unable to mine alt-coins with my s9 nor can i rent it out.
getting only hw errors
getting only hw errors
You realize S9 only mines bitcoins (and other few SHA256 coins)? When you say alt-coins, I assume you mean Scrypt and other protocol alt-coins.
its probably because of "BMminer" instead of CGminer, I'm unable to mine alt-coins with my s9 nor can i rent it out.
getting only hw errors
getting only hw errors
This could be up from the pool cause the network connection may be lost
how much?
I think Antminer increase to 700M newest batchs..
I am using all Bitmain 1600w PSU.
I have found that moving freq down or up doesnt seem to adjust power consumption at the wall very much but it does effect actual hash rate.
I have one miner configured at 593 and others at 650. All hashing almost exactly the same rate and consuming almost exactly the same power.
I have found that moving freq down or up doesnt seem to adjust power consumption at the wall very much but it does effect actual hash rate.
I have one miner configured at 593 and others at 650. All hashing almost exactly the same rate and consuming almost exactly the same power.
By configuration page, Bitmain was referring to the "Miner Status" page and the "Miner configuration pages".
What PSUs are you using?
What PSUs are you using?
this is the key question. I suspect that the s-9 is a little more demanding then the s-7 is,thus some psu's fall short at freq 650.
By configuration page, Bitmain was referring to the "Miner Status" page and the "Miner configuration pages".
What PSUs are you using?
What PSUs are you using?
I have now switched to antpool and it is mining OK.
The fastest I can currently get out of any S9 is 12-13THs.
I have found that with quite a few S9 they only run up to around 7THs at default frequency (650), however, when i turn them down to 625 they come up to 12-13THs.
Has anyone else experimented with the frequency? Have you found any particular frequency to produce better results?
Thanks guys.
The fastest I can currently get out of any S9 is 12-13THs.
I have found that with quite a few S9 they only run up to around 7THs at default frequency (650), however, when i turn them down to 625 they come up to 12-13THs.
Has anyone else experimented with the frequency? Have you found any particular frequency to produce better results?
Thanks guys.
wrong screen shot. and do try a better pool kano.is is known to work well with s-9's
His picture shows correct reason.
S9 do not use Cgminer 4.8.0 Instead is BMminer Version 1.0.0
That is the right reason. You can only use some BTC miningpools and not mine any Altcoins.
Can you share the screen shot of the main control panel page immediately after you log in to your S9?
Thank you!
Thank you!
Antminer S9 does not work at
stratum+tcp://sha256.eu.nicehash.com:3334
Click on the image
The reason is not the S9 speed
Even my double S7 working at speed 9,5THs ,
S9 do not use Cgminer 4.8.0 Instead is BMminer Version 1.0.0
Apparently, this is the problem.
When Bitmain fix this error ?
Arghhh, this must be some state-of-the-art new-kind-of mining software where Bitmain obviously did try to reinvent the wheel instead of using the working solution (aka cgminer). We'll contact Bitmain and ask them to check what kind of bugs did they introduce in Antiner S9 "BMminer" and will ask them to fix the bugs and make it compatible with NiceHash system. Thank you very much for the feedback!
Can you share the screen shot of the main control panel page immediately after you log in to your S9?
Thank you!
Thank you!
Hi Guys,
I just swapped out 6x SP30 for 10x S9 and 2x S7.
The S7 are running fine, however, the S9 are all showing <1THs at the pool for some reason.
I am mining on ghash.io and slushpool.
Does anyone have any suggestions as to what could be causing that?
Thanks guys,
I just swapped out 6x SP30 for 10x S9 and 2x S7.
The S7 are running fine, however, the S9 are all showing <1THs at the pool for some reason.
I am mining on ghash.io and slushpool.
Does anyone have any suggestions as to what could be causing that?
Thanks guys,
Hi Guys,
Please see the screen shot at the link below.
https://1drv.ms/i/s!AgwFONjNYqXLjLQ5XH0x8lApwRAFEA
wrong screen shot. and do try a better pool kano.is is known to work well with s-9's
Can you share the screen shot of the main control panel page immediately after you log in to your S9?
Thank you!
Thank you!
Hi Guys,
I just swapped out 6x SP30 for 10x S9 and 2x S7.
The S7 are running fine, however, the S9 are all showing <1THs at the pool for some reason.
I am mining on ghash.io and slushpool.
Does anyone have any suggestions as to what could be causing that?
Thanks guys,
I just swapped out 6x SP30 for 10x S9 and 2x S7.
The S7 are running fine, however, the S9 are all showing <1THs at the pool for some reason.
I am mining on ghash.io and slushpool.
Does anyone have any suggestions as to what could be causing that?
Thanks guys,
Hi Guys,
Please see the screen shot at the link below.
https://1drv.ms/i/s!AgwFONjNYqXLjLQ5XH0x8lApwRAFEA
Can you share the screen shot of the main control panel page immediately after you log in to your S9?
Thank you!
Thank you!
Hi Guys,
I just swapped out 6x SP30 for 10x S9 and 2x S7.
The S7 are running fine, however, the S9 are all showing <1THs at the pool for some reason.
I am mining on ghash.io and slushpool.
Does anyone have any suggestions as to what could be causing that?
Thanks guys,
I just swapped out 6x SP30 for 10x S9 and 2x S7.
The S7 are running fine, however, the S9 are all showing <1THs at the pool for some reason.
I am mining on ghash.io and slushpool.
Does anyone have any suggestions as to what could be causing that?
Thanks guys,
Hi Guys,
I just swapped out 6x SP30 for 10x S9 and 2x S7.
The S7 are running fine, however, the S9 are all showing <1THs at the pool for some reason.
I am mining on ghash.io and slushpool.
Does anyone have any suggestions as to what could be causing that?
Thanks guys,
I just swapped out 6x SP30 for 10x S9 and 2x S7.
The S7 are running fine, however, the S9 are all showing <1THs at the pool for some reason.
I am mining on ghash.io and slushpool.
Does anyone have any suggestions as to what could be causing that?
Thanks guys,
Jump to: