Wow, BITMAIN bringing the support team. NICE!!!
I have had this problem before. The things that I did were as such!!
1. Make sure the antminer is set to dynamic (DHCP) and not static. It just makes thing much much easier.
2. Find that IP address. To do this login to your router. 192.168.1.1 or 10.0.0.1 (Xfinity). Once you're in go to "connected devices" (It should say something like this). Once there find the antminer on the chart.
3. Go to that IP!!
4. If it hashes GREAT but one more thing.
5. Make sure you have a password in the password box under Miner Configuration. Also, you may want to try a different pool. I suggest Slush. Some of my miners would not work with ANTPOOL but they all work on SLUSH!!
Hope this Helps
Topic: 3x Antminer S3 problems (Read 1188 times)
What country are you located in?
if you are in USA, you can send 1 unit to Denver, Colorado to be tested. Techs can tell you whats wrong with it. I suspect some config issue but hard to diagnose remotely in this case.
If you are in Russia, Ukraine or Venezuela, you can send it to the repair center locally in your country as well. (Just 1 unit to be tested so you'll know what is causing it. Shipping fee is on you but it may be a fastest way to resolve this)
You can email [email protected] for the request
if you are in USA, you can send 1 unit to Denver, Colorado to be tested. Techs can tell you whats wrong with it. I suspect some config issue but hard to diagnose remotely in this case.
If you are in Russia, Ukraine or Venezuela, you can send it to the repair center locally in your country as well. (Just 1 unit to be tested so you'll know what is causing it. Shipping fee is on you but it may be a fastest way to resolve this)
You can email [email protected] for the request
Hey guys!
I'm having the same problem with the 3 antminer that I have at home. They are with all leds turned on, I can access them with web interface and ssh but they won't hash.
I already tried to serial into them to erase rootfs, flash a new different firmware, tried different PSU's
The funny thing is that if I connect just one blade to the controller I can successfuly hash..
Can someone give me some advice?
Best regards
I'm having the same problem with the 3 antminer that I have at home. They are with all leds turned on, I can access them with web interface and ssh but they won't hash.
I already tried to serial into them to erase rootfs, flash a new different firmware, tried different PSU's
The funny thing is that if I connect just one blade to the controller I can successfuly hash..
Can someone give me some advice?
Best regards
I can just have one plugged at a time:
I flashed via GUI, via Serial and via SSH, nothing seems to work
I flashed via GUI, via Serial and via SSH, nothing seems to work
And you have tried the other one on connector and it works fine with just one? (IE chain 1 in this case)
Trying to gather info. You have an odd issue for sure for 3 to all go to one blade mining ok. Did you have any storms or any electrical problems before this happened?
I can just have one plugged at a time:
https://i.imgur.com/kBTTTus.png
I flashed via GUI, via Serial and via SSH, nothing seems to work
https://i.imgur.com/kBTTTus.png
I flashed via GUI, via Serial and via SSH, nothing seems to work
I tried all miners with my RM850 and the problem remains.
Basically I connected like this
https://bitcointalksearch.org/topic/guide-taugerans-antminer-s1s3-revival-story-guide-775662
and entered the following commands
tftpboot 0x80000000 antMiner_xxxx.bin
erase 0x9f020000 +0x7c0000
cp.b 0x80000000 0x9f020000 0x7c0000
reset
Basically I connected like this
https://bitcointalksearch.org/topic/guide-taugerans-antminer-s1s3-revival-story-guide-775662
and entered the following commands
tftpboot 0x80000000 antMiner_xxxx.bin
erase 0x9f020000 +0x7c0000
cp.b 0x80000000 0x9f020000 0x7c0000
reset
Did you try flashing firmware via the GUI? Or were you using the serial to usb, as that seems like what link is talking about.
The RM850 should have no problem powering 1, so we can rule out power as cause. When you say it would run with 1 hashing board earlier on are you able to do this with both blades? (Meaning both blades work just have to be plugged in one at a time).
ATM red and green led are not solid but blinking and ethernet leds are solid.
system log
kernel log
system log
Code:
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.000000] Writing ErrCtl register=00000000
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.000000] Readback ErrCtl register=00000000
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.000000] Memory: 61336k/65536k available (2187k kernel code, 4200k reserved, 588k data, 232k init, 0k highmem)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.000000] NR_IRQS:51
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.080000] pid_max: default: 32768 minimum: 301
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.080000] Mount-cache hash table entries: 512
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.090000] NET: Registered protocol family 16
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 0.100000] MAC FF:FF:FF:FF:FF:FF
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 0.100000] MAC 20:59:a0:c6:47:0e
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.560000] bio: create slabat 0
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.560000] Switching to clocksource MIPS
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.570000] NET: Registered protocol family 2
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.580000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.580000] TCP: Hash tables configured (established 512 bind 512)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.590000] TCP: reno registered
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.610000] NET: Registered protocol family 1
Thu Jan 1 08:00:42 1970 kern.debug kernel: [ 0.610000] PCI: CLS 0 bytes, default 32
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.630000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.640000] msgmni has been set to 119
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.650000] io scheduler noop registered
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.650000] io scheduler deadline registered (default)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.670000] console [ttyATH0] enabled, bootconsole disabled
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 0.690000] m25p80 spi0.0: found gd25q64, expected m25p80
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.690000] m25p80 spi0.0: gd25q64 (8192 Kbytes)
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 0.700000] 5 tp-link partitions found on MTD device spi0.0
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 0.700000] Creating 5 MTD partitions on "spi0.0":
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 0.710000] 0x000000000000-0x000000020000 : "u-boot"
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 0.710000] 0x000000020000-0x000000117dd4 : "kernel"
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 0.730000] 0x000000117dd4-0x0000007f0000 : "rootfs"
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 0.730000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 0.750000] mtd: partition "rootfs" set to be root filesystem
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.750000] mtd: partition "rootfs_data" created automatically, ofs=0x370000, len=0x480000
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 0.760000] 0x000000370000-0x0000007f0000 : "rootfs_data"
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 0.770000] 0x000000020000-0x0000007f0000 : "firmware"
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 0.770000] 0x0000007f0000-0x000000800000 : "art"
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.790000] libphy: ag71xx_mdio: probed
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 0.800000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 1.350000] eth0: Found an AR7240/AR9330 built-in switch
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 2.390000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 2.940000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 2.950000] TCP: cubic registered
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 2.950000] NET: Registered protocol family 17
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 2.960000] 8021q: 802.1Q VLAN Support v1.8
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 2.980000] Freeing unused kernel memory: 232K (80316000 - 80350000)
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.740000] usbcore: registered new interface driver usbfs
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.740000] usbcore: registered new interface driver hub
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.750000] usbcore: registered new device driver usb
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.760000] usbcore: registered new interface driver bitmain
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 5.760000] hash ok
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 5.760000] hashtest OK
Thu Jan 1 08:00:42 1970 kern.err kernel: [ 5.770000] bitmain-asic: success to register device
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.770000] usbcore: registered new interface driver bitmainbl
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.780000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.790000] ehci-platform: EHCI generic platform driver
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.790000] ehci-platform ehci-platform: EHCI Host Controller
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.800000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.810000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.830000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.830000] hub 1-0:1.0: USB hub found
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 5.830000] hub 1-0:1.0: 1 port detected
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 6.180000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 6.330000] hub 1-1:1.0: USB hub found
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 6.330000] hub 1-1:1.0: 2 ports detected
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 6.620000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
Thu Jan 1 08:00:42 1970 kern.err kernel: [ 6.720000] usb 1-1.1: device descriptor read/64, error -32
Thu Jan 1 08:00:42 1970 kern.err kernel: [ 6.910000] usb 1-1.1: device descriptor read/64, error -32
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 7.100000] usb 1-1.1: new full-speed USB device number 4 using ehci-platform
Thu Jan 1 08:00:42 1970 kern.err kernel: [ 7.200000] usb 1-1.1: device descriptor read/64, error -32
Thu Jan 1 08:00:42 1970 kern.err kernel: [ 7.390000] usb 1-1.1: device descriptor read/64, error -32
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 7.580000] usb 1-1.1: new full-speed USB device number 5 using ehci-platform
Thu Jan 1 08:00:42 1970 kern.err kernel: [ 8.000000] usb 1-1.1: device not accepting address 5, error -32
Thu Jan 1 08:00:42 1970 kern.info kernel: [ 8.100000] usb 1-1.1: new full-speed USB device number 6 using ehci-platform
Thu Jan 1 08:00:42 1970 kern.err kernel: [ 8.520000] usb 1-1.1: device not accepting address 6, error -32
Thu Jan 1 08:00:42 1970 kern.err kernel: [ 8.520000] hub 1-1:1.0: unable to enumerate USB device on port 1
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 10.490000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 10.500000] jffs2_build_filesystem(): unlocking the mtd device... done.
Thu Jan 1 08:00:42 1970 kern.warn kernel: [ 10.500000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
Thu Jan 1 08:00:42 1970 kern.notice kernel: [ 41.710000] jffs2: notice: (324) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
Mon Dec 2 11:28:00 2013 daemon.info sysinit: Mon Dec 2 03:28:00 UTC 2013
Mon Dec 2 11:28:00 2013 user.emerg syslog: kmodloader: loading kernel modules from /etc/modules.d/**
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.340000] hidraw: raw HID events driver (C) Jiri Kosina
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.350000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.350000] Backport generated by backports.git backports-20130617-4-ge3220f5
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.370000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.390000] usbcore: registered new interface driver usbhid
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.400000] usbhid: USB HID core driver
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.400000] usbcore: registered new interface driver usbserial
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.410000] usbcore: registered new interface driver usbserial_generic
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.420000] usbserial: USB Serial support registered for generic
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.450000] xt_time: kernel timezone is -0000
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.470000] cfg80211: Calling CRDA to update world regulatory domain
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.470000] cfg80211: World regulatory domain updated:
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.480000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.490000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.500000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.500000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.510000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.520000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.530000] ip_tables: (C) 2000-2006 Netfilter Core Team
Mon Dec 2 11:28:00 2013 kern.debug kernel: [ 44.670000] ath: EEPROM regdomain: 0x0
Mon Dec 2 11:28:00 2013 kern.debug kernel: [ 44.670000] ath: EEPROM indicates default country code should be used
Mon Dec 2 11:28:00 2013 kern.debug kernel: [ 44.670000] ath: doing EEPROM country->regdmn map search
Mon Dec 2 11:28:00 2013 kern.debug kernel: [ 44.670000] ath: country maps to regdmn code: 0x3a
Mon Dec 2 11:28:00 2013 kern.debug kernel: [ 44.670000] ath: Country alpha2 being used: US
Mon Dec 2 11:28:00 2013 kern.debug kernel: [ 44.670000] ath: Regpair used: 0x3a
Mon Dec 2 11:28:00 2013 kern.debug kernel: [ 44.680000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.690000] cfg80211: Calling CRDA for country: US
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.690000] cfg80211: Regulatory domain changed to country: US
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.700000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.710000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.720000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.720000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.730000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.740000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.750000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
Mon Dec 2 11:28:00 2013 kern.info kernel: [ 44.750000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
Mon Dec 2 11:28:00 2013 user.info syslog: ran 16 iterations
Mon Dec 2 11:28:00 2013 daemon.info sysinit: kmod: ran 16 iterations
Mon Dec 2 11:28:02 2013 daemon.info sysinit: Command failed: Not found
Mon Dec 2 11:28:03 2013 cron.info crond[547]: crond: crond (busybox 1.19.4) started, log level 5
Mon Dec 2 11:28:03 2013 daemon.info sysinit: led
Mon Dec 2 11:28:03 2013 daemon.info sysinit: led
Mon Dec 2 11:28:03 2013 daemon.info sysinit: led
Mon Dec 2 11:28:03 2013 daemon.info sysinit: led
Mon Dec 2 11:28:03 2013 daemon.info sysinit: led
Mon Dec 2 11:28:03 2013 daemon.info sysinit: led
Mon Dec 2 11:28:03 2013 daemon.info sysinit: led
Mon Dec 2 11:28:03 2013 user.notice migrate-switchX: Updating switch names in network configuration
Mon Dec 2 11:28:03 2013 daemon.info sysinit: uci: Entry not found
Mon Dec 2 11:28:03 2013 daemon.info sysinit: uci: Parse error (invalid command) at line 1, byte 0
Mon Dec 2 11:28:03 2013 daemon.info sysinit: uci: Entry not found
Mon Dec 2 11:28:03 2013 daemon.info sysinit: uci: Parse error (invalid character in field) at line 1, byte 8
Mon Dec 2 11:28:06 2013 authpriv.info dropbear[692]: Not backgrounding
Mon Dec 2 11:28:06 2013 daemon.notice netifd: Interface 'loopback' is now up
Mon Dec 2 11:28:06 2013 kern.info kernel: [ 50.900000] device eth0 entered promiscuous mode
Mon Dec 2 11:28:07 2013 daemon.notice netifd: lan (744): udhcpc (v1.19.4) started
Mon Dec 2 11:28:07 2013 daemon.notice netifd: wan (749): udhcpc (v1.19.4) started
Mon Dec 2 11:28:07 2013 daemon.notice netifd: lan (744): Sending discover...
Mon Dec 2 11:28:08 2013 daemon.notice netifd: wan (749): Sending discover...
Mon Dec 2 11:28:09 2013 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Mon Dec 2 11:28:09 2013 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Mon Dec 2 11:28:09 2013 kern.info kernel: [ 53.360000] eth1: link up (100Mbps/Full duplex)
Mon Dec 2 11:28:09 2013 daemon.info sysinit: /etc/config/miner_pic.hex
Mon Dec 2 11:28:09 2013 daemon.info sysinit: Unable to open /dev/bitmainbl0: No such file or directory
Mon Dec 2 11:28:09 2013 daemon.info sysinit: pic update
Mon Dec 2 11:28:09 2013 daemon.info dnsmasq[789]: started, version 2.66 cachesize 150
Mon Dec 2 11:28:09 2013 daemon.info dnsmasq[789]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth
Mon Dec 2 11:28:09 2013 daemon.info dnsmasq[789]: using local addresses only for domain lan
Mon Dec 2 11:28:09 2013 daemon.warn dnsmasq[789]: no servers found in /tmp/resolv.conf.auto, will retry
Mon Dec 2 11:28:09 2013 daemon.info dnsmasq[789]: read /etc/hosts - 1 addresses
Mon Dec 2 11:28:09 2013 daemon.info sysinit: setting up led WAN
Mon Dec 2 11:28:09 2013 daemon.info sysinit: setting up led WANL
Mon Dec 2 11:28:09 2013 daemon.info sysinit: setting up led LAN1
Mon Dec 2 11:28:09 2013 daemon.info sysinit: setting up led LAN2
Mon Dec 2 11:28:09 2013 daemon.info sysinit: setting up led LAN3
Mon Dec 2 11:28:09 2013 daemon.info sysinit: setting up led LAN4
Mon Dec 2 11:28:09 2013 daemon.info sysinit: setting up led WLAN
Mon Dec 2 11:28:10 2013 daemon.notice netifd: lan (744): Sending discover...
Mon Dec 2 11:28:11 2013 daemon.notice netifd: wan (749): Sending discover...
Mon Dec 2 11:28:11 2013 daemon.notice netifd: wan (749): Sending select for 192.168.1.223...
Mon Dec 2 11:28:11 2013 daemon.notice netifd: wan (749): Lease of 192.168.1.223 obtained, lease time 86400
Mon Dec 2 11:28:11 2013 daemon.notice netifd: Interface 'wan' is now up
Mon Dec 2 11:28:11 2013 daemon.info dnsmasq[789]: reading /tmp/resolv.conf.auto
Mon Dec 2 11:28:11 2013 daemon.info dnsmasq[789]: using nameserver 8.8.4.4#53
Mon Dec 2 11:28:11 2013 daemon.info dnsmasq[789]: using nameserver 8.8.8.8#53
Mon Dec 2 11:28:11 2013 daemon.info dnsmasq[789]: using local addresses only for domain lan
Mon Dec 2 11:28:12 2013 user.notice firewall: Reloading firewall due to ifup of wan (eth1)
Mon Dec 2 11:28:12 2013 daemon.info sysinit: --bitmain-options 115200:32:8:18:225:0882 -o stratum.antpool.com:3333 -O Icipher.200:sdhsdfh --api-listen --api-network --bitmain-checkn2diff --bitmain-hwerror --bitmain-voltage 0000 --version-file /usr/bin/compile_time --queue 4096
Mon Dec 2 11:28:12 2013 daemon.info sysinit: - init complete -
Mon Dec 2 11:28:14 2013 daemon.notice netifd: lan (744): Sending discover...
Thu May 26 22:32:45 2016 cron.err crond[547]: time disparity of 1305304 minutes detected
Thu May 26 22:33:01 2016 cron.info crond[547]: crond: USER root pid 956 cmd /usr/bin/cgminer-monitor
kernel log
Code:
[ 0.000000] Linux version 3.10.12 (xxl@armdev01) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38031) ) #31 Fri Jan 9 20:41:54 CST 2015
[ 0.000000] MyLoader: sysp=1bec2fee, boardp=fdd6ef6f, parts=fc031564
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 803005b0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR741ND-v4 console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61336k/65536k available (2187k kernel code, 4200k reserved, 588k data, 232k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.080000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-WR741ND v4
[ 0.100000] MAC FF:FF:FF:FF:FF:FF
[ 0.100000] MAC 20:59:a0:c6:47:0e
[ 0.560000] bio: create slabat 0
[ 0.560000] Switching to clocksource MIPS
[ 0.570000] NET: Registered protocol family 2
[ 0.570000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.580000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.580000] TCP: Hash tables configured (established 512 bind 512)
[ 0.590000] TCP: reno registered
[ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.610000] NET: Registered protocol family 1
[ 0.610000] PCI: CLS 0 bytes, default 32
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.630000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.640000] msgmni has been set to 119
[ 0.650000] io scheduler noop registered
[ 0.650000] io scheduler deadline registered (default)
[ 0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.670000] console [ttyATH0] enabled, bootconsole disabled
[ 0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.690000] m25p80 spi0.0: found gd25q64, expected m25p80
[ 0.690000] m25p80 spi0.0: gd25q64 (8192 Kbytes)
[ 0.700000] 5 tp-link partitions found on MTD device spi0.0
[ 0.700000] Creating 5 MTD partitions on "spi0.0":
[ 0.710000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.710000] 0x000000020000-0x000000117dd4 : "kernel"
[ 0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.730000] 0x000000117dd4-0x0000007f0000 : "rootfs"
[ 0.730000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.750000] mtd: partition "rootfs" set to be root filesystem
[ 0.750000] mtd: partition "rootfs_data" created automatically, ofs=0x370000, len=0x480000
[ 0.760000] 0x000000370000-0x0000007f0000 : "rootfs_data"
[ 0.770000] 0x000000020000-0x0000007f0000 : "firmware"
[ 0.770000] 0x0000007f0000-0x000000800000 : "art"
[ 0.790000] libphy: ag71xx_mdio: probed
[ 0.800000] eth0: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 1.350000] eth0: Found an AR7240/AR9330 built-in switch
[ 2.390000] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.940000] ag71xx ag71xx.0 eth1: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 2.950000] TCP: cubic registered
[ 2.950000] NET: Registered protocol family 17
[ 2.960000] 8021q: 802.1Q VLAN Support v1.8
[ 2.970000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.980000] Freeing unused kernel memory: 232K (80316000 - 80350000)
[ 5.740000] usbcore: registered new interface driver usbfs
[ 5.740000] usbcore: registered new interface driver hub
[ 5.750000] usbcore: registered new device driver usb
[ 5.750000] usbcore: registered new interface driver bitmain
[ 5.760000] hash ok
[ 5.760000] hashtest OK
[ 5.770000] bitmain-asic: success to register device
[ 5.770000] usbcore: registered new interface driver bitmainbl
[ 5.780000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.790000] ehci-platform: EHCI generic platform driver
[ 5.790000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.800000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.810000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 5.830000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 5.830000] hub 1-0:1.0: USB hub found
[ 5.830000] hub 1-0:1.0: 1 port detected
[ 6.180000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 6.330000] hub 1-1:1.0: USB hub found
[ 6.330000] hub 1-1:1.0: 2 ports detected
[ 6.620000] usb 1-1.1: new full-speed USB device number 3 using ehci-platform
[ 6.720000] usb 1-1.1: device descriptor read/64, error -32
[ 6.910000] usb 1-1.1: device descriptor read/64, error -32
[ 7.100000] usb 1-1.1: new full-speed USB device number 4 using ehci-platform
[ 7.200000] usb 1-1.1: device descriptor read/64, error -32
[ 7.390000] usb 1-1.1: device descriptor read/64, error -32
[ 7.580000] usb 1-1.1: new full-speed USB device number 5 using ehci-platform
[ 8.000000] usb 1-1.1: device not accepting address 5, error -32
[ 8.100000] usb 1-1.1: new full-speed USB device number 6 using ehci-platform
[ 8.520000] usb 1-1.1: device not accepting address 6, error -32
[ 8.520000] hub 1-1:1.0: unable to enumerate USB device on port 1
[ 10.510000] jffs2: notice: (323) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 18 of xref (0 dead, 3 orphan) found.
[ 13.030000] hidraw: raw HID events driver (C) Jiri Kosina
[ 13.030000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 13.040000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 13.060000] nf_conntrack version 0.5.0 (962 buckets, 3848 max)
[ 13.080000] usbcore: registered new interface driver usbhid
[ 13.080000] usbhid: USB HID core driver
[ 13.090000] usbcore: registered new interface driver usbserial
[ 13.100000] usbcore: registered new interface driver usbserial_generic
[ 13.100000] usbserial: USB Serial support registered for generic
[ 13.130000] xt_time: kernel timezone is -0000
[ 13.170000] cfg80211: Calling CRDA to update world regulatory domain
[ 13.170000] cfg80211: World regulatory domain updated:
[ 13.180000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.180000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.190000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.200000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.210000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.210000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.230000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.360000] ath: EEPROM regdomain: 0x0
[ 13.360000] ath: EEPROM indicates default country code should be used
[ 13.360000] ath: doing EEPROM country->regdmn map search
[ 13.360000] ath: country maps to regdmn code: 0x3a
[ 13.360000] ath: Country alpha2 being used: US
[ 13.360000] ath: Regpair used: 0x3a
[ 13.370000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 13.380000] cfg80211: Calling CRDA for country: US
[ 13.380000] cfg80211: Regulatory domain changed to country: US
[ 13.390000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.400000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 13.400000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 13.410000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.420000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.430000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.440000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 13.440000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 18.480000] device eth0 entered promiscuous mode
[ 21.020000] eth1: link up (100Mbps/Full duplex)
I tried all miners with my RM850 and the problem remains.
Basically I connected like this
https://bitcointalksearch.org/topic/guide-taugerans-antminer-s1s3-revival-story-guide-775662
and entered the following commands
tftpboot 0x80000000 antMiner_xxxx.bin
erase 0x9f020000 +0x7c0000
cp.b 0x80000000 0x9f020000 0x7c0000
reset
Basically I connected like this
https://bitcointalksearch.org/topic/guide-taugerans-antminer-s1s3-revival-story-guide-775662
and entered the following commands
tftpboot 0x80000000 antMiner_xxxx.bin
erase 0x9f020000 +0x7c0000
cp.b 0x80000000 0x9f020000 0x7c0000
reset
They suddenly stopped working..
I tried them one at a time with an Aerocool Strike X 1100W, Corsair RM850, Corsair HX750i (brand new) and the problem persists.
All the controllers can handle just one blade at a time. all the 6 blades are hashing but separately.
I tried them one at a time with an Aerocool Strike X 1100W, Corsair RM850, Corsair HX750i (brand new) and the problem persists.
All the controllers can handle just one blade at a time. all the 6 blades are hashing but separately.
Are you able to run both blades on a single s3 with the 1100W power supply?
None of them =\
I'm not sure on quality of Aerocool Strike X after a little searching. I would try 1 miner with Corsair RM850 and see what happens with just one going.
What all did you change when you were deleting stuff during "I already tried to serial into them to erase rootfs"?
They suddenly stopped working..
I tried them one at a time with an Aerocool Strike X 1100W, Corsair RM850, Corsair HX750i (brand new) and the problem persists.
All the controllers can handle just one blade at a time. all the 6 blades are hashing but separately.
I tried them one at a time with an Aerocool Strike X 1100W, Corsair RM850, Corsair HX750i (brand new) and the problem persists.
All the controllers can handle just one blade at a time. all the 6 blades are hashing but separately.
Are you able to run both blades on a single s3 with the 1100W power supply?
None of them =\
They suddenly stopped working..
I tried them one at a time with an Aerocool Strike X 1100W, Corsair RM850, Corsair HX750i (brand new) and the problem persists.
All the controllers can handle just one blade at a time. all the 6 blades are hashing but separately.
I tried them one at a time with an Aerocool Strike X 1100W, Corsair RM850, Corsair HX750i (brand new) and the problem persists.
All the controllers can handle just one blade at a time. all the 6 blades are hashing but separately.
Are you able to run both blades on a single s3 with the 1100W power supply?
They suddenly stopped working..
I tried them one at a time with an Aerocool Strike X 1100W, Corsair RM850, Corsair HX750i (brand new) and the problem persists.
All the controllers can handle just one blade at a time. all the 6 blades are hashing but separately.
I tried them one at a time with an Aerocool Strike X 1100W, Corsair RM850, Corsair HX750i (brand new) and the problem persists.
All the controllers can handle just one blade at a time. all the 6 blades are hashing but separately.
Hey guys!
I'm having the same problem with the 3 antminer that I have at home. They are with all leds turned on, I can access them with web interface and ssh but they won't hash.
I already tried to serial into them to erase rootfs, flash a new different firmware, tried different PSU's
The funny thing is that if I connect just one blade to the controller I can successfuly hash..
Can someone give me some advice?
Best regards
I'm having the same problem with the 3 antminer that I have at home. They are with all leds turned on, I can access them with web interface and ssh but they won't hash.
I already tried to serial into them to erase rootfs, flash a new different firmware, tried different PSU's
The funny thing is that if I connect just one blade to the controller I can successfuly hash..
Can someone give me some advice?
Best regards
What PSU's are you trying when you said tried different ones? I ask as if it can run one blade... make me maybe look at power. At least that is where I would look.
The odd thing is to have same problem on 3 antminers. Are they new to you? Or have you had them and they suddenly stopped working?
Hey guys!
I'm having the same problem with the 3 antminer that I have at home. They are with all leds turned on, I can access them with web interface and ssh but they won't hash.
I already tried to serial into them to erase rootfs, flash a new different firmware, tried different PSU's
The funny thing is that if I connect just one blade to the controller I can successfuly hash..
Can someone give me some advice?
Best regards
I'm having the same problem with the 3 antminer that I have at home. They are with all leds turned on, I can access them with web interface and ssh but they won't hash.
I already tried to serial into them to erase rootfs, flash a new different firmware, tried different PSU's
The funny thing is that if I connect just one blade to the controller I can successfuly hash..
Can someone give me some advice?
Best regards
Jump to: