6950 poor performance | Bitcointalksearch.org

portron

member

Activity: 106

Merit: 10

Quote from: psycosis on November 02, 2011, 05:26:08 PM

I think its close enough too.
Surprised that without unlocking those shaders the card isn't coming anywhere near the stock figures. i think this is due to the card running a lower cpu speed for some reason. It didn't seem to be running at 800Mhz properly.

Case is on its side due to space, so i will leave it at that.

Just use the ATI CC (the official tool) and up the clock speed a little. You won't damage your card or anything. I have a couple 6950's each pull ~375-380.

MyZhre

full member

Activity: 193

Merit: 100

I got about 390MH/S with GUIMiner/OpenCL, Win7

RyNinDaCleM

legendary

Activity: 2408

Merit: 1009

Legen -wait for it- dary

Try running CGminer with -I 8, and leave out the -v -w128. Those are the default settings.

psycosis

newbie

Activity: 4

Merit: 0

I think its close enough too.
Surprised that without unlocking those shaders the card isn't coming anywhere near the stock figures. i think this is due to the card running a lower cpu speed for some reason. It didn't seem to be running at 800Mhz properly.

Case is on its side due to space, so i will leave it at that.

jake262144

full member

Activity: 210

Merit: 100

318? I'd call it close enough for government job, would you agree? ^^
You might try OC'ing it a bit, just because it's a decent card you got there.

These paramters are used for fine-tuning the miner to your card.
The -w parameter is the work size which can range from 64 to 256. Generally, for a 6950 the optimal value is 128.
-v enables vectors. You DO want to do this.
-f is for tuning the mining aggression (basically, the load on your card); the LOWER walue here, the more aggressive the mining.

FYI, GUIminer is but a frontend - the actual miner (down below the pretty gui) is, in your case, poclbm.
Below you can see the current source code for poclbm, all possible parameters, their default values and meaning are explained there:
https://github.com/m0mchil/poclbm/blob/076f85c63d1ce21c81695eed9b60eb778a0f1ade/poclbm.py

Good luck!

PS. In your first post, you were like "i don't want to mess too much"
After a while you added the "-v -f30 -w128" string
Dude, by this rate tomorrow you'll be building a dedicated mining rig

psycosis

newbie

Activity: 4

Merit: 0

Using Guiminer on windows 7 x64
not using any special params and this is a workstation so i don't want to mess too much.

I noticed Saphire have handly included a switch which already unlocks the shaders. So in this mode its running 800mhz and 1536 shaders. i now get 318.
this is still with the stock settings.

If i use -v -f30 -w128 then i get 352.9mh/s
What exactly are these commands changing?

jake262144

full member

Activity: 210

Merit: 100

Miner and parameters?
Operating system?
Is it a dedicated rig or your workstation? A web browser running some flash will totally demolish your mining speed.

EDIT: You should be getting at least 310 Mhash out of this thing using any contemporary and well-tuned miner if it's a dedicated mining card.

psycosis

newbie

Activity: 4

Merit: 0

Hello,

I have a stock 6950 and i am getting only 250mh/s from it.
I have the most uptodate ATI drivers and it will not go up, i was under the impression this should be a lot faster without any changes.

Anyone got any ideas what could be up.

Thanks

Topic: 6950 poor performance (Read 1189 times)