very likely the riser side issue.
check all connection
check and swap the usb cable
check and swap the riser
i had that issue before and it also can cause memory error with some not so good riser
Topic: AMD card not detected. 6 card only 5 detected (Read 408 times)
try this:
BIOS -> Enable 4G Decoding
Let me know if it works for you. I have fount this in this forum and didn't tested yet
BIOS -> Enable 4G Decoding
Let me know if it works for you. I have fount this in this forum and didn't tested yet
BIOS already updated. I will try that after. Never have that problem with asrock btc,
try this:
BIOS -> Enable 4G Decoding
Let me know if it works for you. I have fount this in this forum and didn't tested yet
BIOS -> Enable 4G Decoding
Let me know if it works for you. I have fount this in this forum and didn't tested yet
I had the same issue with Asrock h81 PROBTC motherboard. To solve this issue I had to install a patch for windows 8. I was using windows 8.
Anyway the psu you have is too small for 6 cards. The consum for 1 card is about 120-150W in full load.
Anyway the psu you have is too small for 6 cards. The consum for 1 card is about 120-150W in full load.
It's rx 460 very low power.
What patch did you use?
Sounds like bad risers.
Unplug all the cards, then plug 1 in at a time until you find out which one has the problem. Then try another card in that riser AND try that card in a different riser.
Unplug all the cards, then plug 1 in at a time until you find out which one has the problem. Then try another card in that riser AND try that card in a different riser.
The card and risers work well on asrock btc. The problem is also made difficult by the fact that all rx 460 fans keep running. So I can't tell which one isn't detected.
That is. Even if claymore is inactive, all the fans are doing 1200 rpm.
All are sapphire rx 460.
I wonder if it's the card or the mobo or what?
Sounds like bad risers.
Unplug all the cards, then plug 1 in at a time until you find out which one has the problem. Then try another card in that riser AND try that card in a different riser.
Unplug all the cards, then plug 1 in at a time until you find out which one has the problem. Then try another card in that riser AND try that card in a different riser.
I had the same issue with Asrock h81 PROBTC motherboard. To solve this issue I had to install a patch for windows 8. I was using windows 8.
Anyway the psu you have is too small for 6 cards. The consum for 1 card is about 120-150W in full load.
Anyway the psu you have is too small for 6 cards. The consum for 1 card is about 120-150W in full load.
I am using windows 10
Does the mothoerboard itself have drivers?
Do the fans keep running too?
I had the same issue with Asrock h81 PROBTC motherboard. To solve this issue I had to install a patch for windows 8. I was using windows 8.
Anyway the psu you have is too small for 6 cards. The consum for 1 card is about 120-150W in full load.
Anyway the psu you have is too small for 6 cards. The consum for 1 card is about 120-150W in full load.
How do I even trouble shoot this
- motherboard A88X-G45
- 1 psu 650watt
- 6 VGA 460 sapphire.
6 fans in VGA all running and only 5 detected
I wonder why my VGA only 5 detected ?
I try to turn off claymore. Result is all fan are on despite GPU 0%. Another miracle.
So it's hard for me to know which card is problematic
Only 6 cards show up on device manager, wattool etc.
All fans are running irrelevant of whether I am using them for mining or not.
Something is just wrong.
I suspect the problem is because I am using my PSU sata power cable to power 4 sata risers.
I am using rx 460. My PSU have 650 watt capacity. The whole rig need only 350 watt last time I check.
The 6 pin power is not used because of this.
- motherboard A88X-G45
- 1 psu 650watt
- 6 VGA 460 sapphire.
6 fans in VGA all running and only 5 detected
I wonder why my VGA only 5 detected ?
I try to turn off claymore. Result is all fan are on despite GPU 0%. Another miracle.
So it's hard for me to know which card is problematic
Only 6 cards show up on device manager, wattool etc.
All fans are running irrelevant of whether I am using them for mining or not.
Something is just wrong.
I suspect the problem is because I am using my PSU sata power cable to power 4 sata risers.
I am using rx 460. My PSU have 650 watt capacity. The whole rig need only 350 watt last time I check.
The 6 pin power is not used because of this.
Jump to: