Another S9 card FOOKED !!!! | Bitcointalksearch.org

Sandal_Hat

full member

Activity: 462

Merit: 118

Quote from: Dragonizer on October 22, 2017, 03:42:01 PM

Cheers, Photobucket have a cheek !!! It's slow as hell as well

How long have u been running it. It stopped at that 76-81 temperature? I thought that was a good temp?

U switch PSU. Are u using bitmain PSU or a different PSU?

Quote from: Scrappy Do on October 23, 2017, 01:20:35 PM

Quote from: Dragonizer on October 23, 2017, 02:59:26 AM

Quote from: Scrappy Do on October 22, 2017, 04:50:08 PM

You only have 2 boards even showing up. Looks like the controller isn't even plugged in. Even with a bad board, it should still show up with all xxxxxxxxxxxx . Check the controller plug on the missing board.

Lemme know more...

Scrap'

It was showing 3 boards mate, rebooting via logging in done nothing and still showed 3 boards, it ONLY went to 2 boards when i physically unplugged it ?

I have checked the ribbon cables between controller and board and is fine.

Also my other faulty miners only show 2 boards, they are the new type self adjusting fan speedd/frequency as well...So it is the norm for me.

I have also swapped pcie-e connections from good board and even new psu's.

NOT worth sending back as they are 11.5Th models and run at 9.6Th !!!

Just hate losing hash power when i have access to free leccy !

Cheers Mate

It is only showing 2 boards bro, something is going on with the controller I'm telling you. Try the ribbon cables 1 by 1 on each card till you find the bad cable or board. If you will notice when you add the 2 it shows together with the amount of each one, it will be full speed. 1 board is not showing at all.

Trust me I have over 20 s9'2 and they have different versions of firmware yet all of them show all 3 boards.

Scrap'

How long u been running them and at wat temperature?

Scrappy Do

hero member

Activity: 686

Merit: 500

Quote from: Upstream on October 23, 2017, 10:11:00 PM

Quote from: Scrappy Do on October 23, 2017, 04:19:59 PM

*snip*

I am saying that it should still show the board unless it is really bad. I have 1 machine that has some chips out, but it still shows in the config screen. Do your bad boards not show on the config screen at all?

Yes I have boards that do not even show up on the miner status screen. For example it will say Chain 6, Chain 7 but no Chain 8

Wow. I have never seen this. I started buying from them in the s3 era too. Even swapping the ribbons you still never see the card at all? I understand you may swap and only see 2 again, but are you sure its the same 2 cards? If so, I have to say that's a dead ass board and a problem that luckily I have never seen.

Scrap'

Upstream

newbie

Activity: 41

Merit: 0

Quote from: Scrappy Do on October 23, 2017, 04:19:59 PM

*snip*

I am saying that it should still show the board unless it is really bad. I have 1 machine that has some chips out, but it still shows in the config screen. Do your bad boards not show on the config screen at all?

Yes I have boards that do not even show up on the miner status screen. For example it will say Chain 6, Chain 7 but no Chain 8

not.you

legendary

Activity: 1726

Merit: 1018

How long is bitmainwarranty taking for turn around these days? I communicated with them about a bad board and they were very responsive, like 3 replies within 24 hours. As soon as I sent them the board they stopped responding entirely. They have had possession of my board for 10 days according to UPS and they have ignored 3 different messages from me about the progress or even to confirm they got it.

In the past they fixed my S7 board and had it back in the mail to me faster than this... Huh

Scrappy Do

hero member

Activity: 686

Merit: 500

Quote from: Upstream on October 23, 2017, 03:53:21 PM

Quote from: Scrappy Do on October 23, 2017, 01:20:35 PM

Quote from: Dragonizer on October 23, 2017, 02:59:26 AM

Quote from: Scrappy Do on October 22, 2017, 04:50:08 PM

You only have 2 boards even showing up. Looks like the controller isn't even plugged in. Even with a bad board, it should still show up with all xxxxxxxxxxxx . Check the controller plug on the missing board.

Lemme know more...

Scrap'

It was showing 3 boards mate, rebooting via logging in done nothing and still showed 3 boards, it ONLY went to 2 boards when i physically unplugged it ?

I have checked the ribbon cables between controller and board and is fine.

Also my other faulty miners only show 2 boards, they are the new type self adjusting fan speedd/frequency as well...So it is the norm for me.

I have also swapped pcie-e connections from good board and even new psu's.

NOT worth sending back as they are 11.5Th models and run at 9.6Th !!!

Just hate losing hash power when i have access to free leccy !

Cheers Mate

It is only showing 2 boards bro, something is going on with the controller I'm telling you. Try the ribbon cables 1 by 1 on each card till you find the bad cable or board. If you will notice when you add the 2 it shows together with the amount of each one, it will be full speed. 1 board is not showing at all.

Trust me I have over 20 s9'2 and they have different versions of firmware yet all of them show all 3 boards.

Scrap'

Are you sure about this? I have 30 antminers I just ordered, have maybe 4 or 5 bad boards that I'm prepping to send to Bitmainwarranty, and I've tried switching the cables and PCI-e's to no avail.

I am saying that it should still show the board unless it is really bad. I have 1 machine that has some chips out, but it still shows in the config screen. Do your bad boards not show on the config screen at all?

Upstream

newbie

Activity: 41

Merit: 0

Quote from: Scrappy Do on October 23, 2017, 01:20:35 PM

Quote from: Dragonizer on October 23, 2017, 02:59:26 AM

Quote from: Scrappy Do on October 22, 2017, 04:50:08 PM

You only have 2 boards even showing up. Looks like the controller isn't even plugged in. Even with a bad board, it should still show up with all xxxxxxxxxxxx . Check the controller plug on the missing board.

Lemme know more...

Scrap'

It was showing 3 boards mate, rebooting via logging in done nothing and still showed 3 boards, it ONLY went to 2 boards when i physically unplugged it ?

I have checked the ribbon cables between controller and board and is fine.

Also my other faulty miners only show 2 boards, they are the new type self adjusting fan speedd/frequency as well...So it is the norm for me.

I have also swapped pcie-e connections from good board and even new psu's.

NOT worth sending back as they are 11.5Th models and run at 9.6Th !!!

Just hate losing hash power when i have access to free leccy !

Cheers Mate

It is only showing 2 boards bro, something is going on with the controller I'm telling you. Try the ribbon cables 1 by 1 on each card till you find the bad cable or board. If you will notice when you add the 2 it shows together with the amount of each one, it will be full speed. 1 board is not showing at all.

Trust me I have over 20 s9'2 and they have different versions of firmware yet all of them show all 3 boards.

Scrap'

Are you sure about this? I have 30 antminers I just ordered, have maybe 4 or 5 bad boards that I'm prepping to send to Bitmainwarranty, and I've tried switching the cables and PCI-e's to no avail.

Biffa

legendary

Activity: 3234

Merit: 1221

3rd party but they do a good job ime

promojo

sr. member

Activity: 420

Merit: 250

is bitmainwarranty.com a third-party or actual bitmain entity?

Scrappy Do

hero member

Activity: 686

Merit: 500

Quote from: Dragonizer on October 23, 2017, 02:59:26 AM

Quote from: Scrappy Do on October 22, 2017, 04:50:08 PM

You only have 2 boards even showing up. Looks like the controller isn't even plugged in. Even with a bad board, it should still show up with all xxxxxxxxxxxx . Check the controller plug on the missing board.

Lemme know more...

Scrap'

It was showing 3 boards mate, rebooting via logging in done nothing and still showed 3 boards, it ONLY went to 2 boards when i physically unplugged it ?

I have checked the ribbon cables between controller and board and is fine.

Also my other faulty miners only show 2 boards, they are the new type self adjusting fan speedd/frequency as well...So it is the norm for me.

I have also swapped pcie-e connections from good board and even new psu's.

NOT worth sending back as they are 11.5Th models and run at 9.6Th !!!

Just hate losing hash power when i have access to free leccy !

Cheers Mate

It is only showing 2 boards bro, something is going on with the controller I'm telling you. Try the ribbon cables 1 by 1 on each card till you find the bad cable or board. If you will notice when you add the 2 it shows together with the amount of each one, it will be full speed. 1 board is not showing at all.

Trust me I have over 20 s9'2 and they have different versions of firmware yet all of them show all 3 boards.

Scrap'

Dragonizer

full member

Activity: 279

Merit: 107

Quote from: Scrappy Do on October 22, 2017, 04:50:08 PM

You only have 2 boards even showing up. Looks like the controller isn't even plugged in. Even with a bad board, it should still show up with all xxxxxxxxxxxx . Check the controller plug on the missing board.

Lemme know more...

Scrap'

It was showing 3 boards mate, rebooting via logging in done nothing and still showed 3 boards, it ONLY went to 2 boards when i physically unplugged it ?

I have checked the ribbon cables between controller and board and is fine.

Also my other faulty miners only show 2 boards, they are the new type self adjusting fan speedd/frequency as well...So it is the norm for me.

I have also swapped pcie-e connections from good board and even new psu's.

NOT worth sending back as they are 11.5Th models and run at 9.6Th !!!

Just hate losing hash power when i have access to free leccy !

Cheers Mate

wavelengthsf

full member

Activity: 658

Merit: 118

Quote from: cioloxl on October 22, 2017, 04:56:17 PM

Wait a sec...is this legit? I knew they had a facility in California, but I didn't know about Ukraine. The website is looking good, but I'm worried it might be a fraud...Has anyone from Europe actually sent boards here? Because I'd much rather send it to the country next to mine than have it go to China for 2 months.

Bitmain Warranty is NOT run by Bitmain. They will fix your miners but charge you for the time/repairs/hardware.

cioloxl

full member

Activity: 238

Merit: 105

Quote from: philipma1957 on October 22, 2017, 09:07:24 AM

Quote from: Dragonizer on October 22, 2017, 08:10:49 AM

Hi All

I have twelve S9's and this is the 3rd one to have a 'card' die !!!

They are in a server room, temps low, fans fine.

Live in UK and got totally confused on how to return to China or even whether it's worth it !!

RANT OVER...lol

Cry

bitmainwarranty.com has an USA spot in Colorado and a place in the Ukraine . Wait for links.

https://bitmainwarranty.com/

good luck

Wait a sec...is this legit? I knew they had a facility in California, but I didn't know about Ukraine. The website is looking good, but I'm worried it might be a fraud...Has anyone from Europe actually sent boards here? Because I'd much rather send it to the country next to mine than have it go to China for 2 months.

Scrappy Do

hero member

Activity: 686

Merit: 500

You only have 2 boards even showing up. Looks like the controller isn't even plugged in. Even with a bad board, it should still show up with all xxxxxxxxxxxx . Check the controller plug on the missing board.

Lemme know more...

Scrap'

Dragonizer

full member

Activity: 279

Merit: 107

Cheers, Photobucket have a cheek !!! It's slow as hell as well

leowonderful

legendary

Activity: 1624

Merit: 1130

Bitcoin FTW!

Quote from: Dragonizer on October 22, 2017, 12:26:50 PM

Quote from: Scrappy Do on October 22, 2017, 12:16:36 PM

Are these s9's out of warranty?

What batch are they?

I can tell you that many of my later s9'2 will shut down a card, yet run nonstop. It sounds like a heat issue to me.

Can you adjust the speed? Or have you already?

Pretty simple if you know what your looking for. If the miner runs and a card shuts down, check the fan speeds and see what card is causing the problem.

Give me more info bro, I can help you with this. Been there done that.

Scrap'

Hi Scrappy, not checked the Serial Number yet...Can not adjust Frequency etc as it's latter self setting type..I know what card it is as i have screen shot below, plus it does NOT have a red 'stop dog' light on stating it's OK....

http://img.photobucket.com/albums/v662/romanski/S9%20Faulty_154_zpsbsbnbxnk.jpg

Photobucket doesn't work anymore these days (they want you to pay extra money for third party viewing), you need a new image hoster. Imgur works well if you're not trying to embed it in a post.

Dragonizer

full member

Activity: 279

Merit: 107

Quote from: Scrappy Do on October 22, 2017, 12:16:36 PM

Are these s9's out of warranty?

What batch are they?

I can tell you that many of my later s9'2 will shut down a card, yet run nonstop. It sounds like a heat issue to me.

Can you adjust the speed? Or have you already?

Pretty simple if you know what your looking for. If the miner runs and a card shuts down, check the fan speeds and see what card is causing the problem.

Give me more info bro, I can help you with this. Been there done that.

Scrap'

Hi Scrappy, not checked the Serial Number yet...Can not adjust Frequency etc as it's latter self setting type..I know what card it is as i have screen shot below, plus it does NOT have a red 'stop dog' light on stating it's OK....

http://img.photobucket.com/albums/v662/romanski/S9%20Faulty_154_zpsbsbnbxnk.jpg

Scrappy Do

hero member

Activity: 686

Merit: 500

Are these s9's out of warranty?

What batch are they?

I can tell you that many of my later s9'2 will shut down a card, yet run nonstop. It sounds like a heat issue to me.

Can you adjust the speed? Or have you already?

Pretty simple if you know what your looking for. If the miner runs and a card shuts down, check the fan speeds and see what card is causing the problem.

Give me more info bro, I can help you with this. Been there done that.

Scrap'

Dragonizer

full member

Activity: 279

Merit: 107

Quote from: philipma1957 on October 22, 2017, 09:07:24 AM

Quote from: Dragonizer on October 22, 2017, 08:10:49 AM

Hi All

I have twelve S9's and this is the 3rd one to have a 'card' die !!!

They are in a server room, temps low, fans fine.

Live in UK and got totally confused on how to return to China or even whether it's worth it !!

RANT OVER...lol

Cry

bitmainwarranty.com has an USA spot in Colorado and a place in the Ukraine . Wait for links.

https://bitmainwarranty.com/

good luck

Cheers mate, in work atm, so not looked into it, are you UK based ?

Is it 'cost Effective' to return for the sake of 4Th max ?

Or should i just sell on Ebay and purchase new from Bitmain ??

What do you reckon ?

Thanks

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: Dragonizer on October 22, 2017, 08:10:49 AM

Hi All

I have twelve S9's and this is the 3rd one to have a 'card' die !!!

They are in a server room, temps low, fans fine.

Live in UK and got totally confused on how to return to China or even whether it's worth it !!

RANT OVER...lol

Cry

bitmainwarranty.com has an USA spot in Colorado and a place in the Ukraine . Wait for links.

https://bitmainwarranty.com/

good luck

Dragonizer

full member

Activity: 279

Merit: 107

Hi All

I have twelve S9's and this is the 3rd one to have a 'card' die !!!

They are in a server room, temps low, fans fine.

Live in UK and got totally confused on how to return to China or even whether it's worth it !!

RANT OVER...lol

Cry

Topic: Another S9 card FOOKED !!!! (Read 820 times)