see this thread to set S1's to auto reboot.
https://bitcointalksearch.org/topic/do-your-s1s-stop-hashing-reboot-it-automatically-587268
Topic: antminer S1: connect via LAN, setup WWAN, but can't access via wifi (Read 2681 times)
April 27, 2014, 09:27:53 PM
I caved. I just drilled holes, climbed in the top crawl space and ran cat6 to the other room. My next problem is, it stops mining after 30 mins (beeping sound).
Chain 1 Fan 2220 Temp 39
Chain 2 Fan 0 Temp 42
I have a honeywell blowing air on it. I only have one mining pool set up.
Chain 1 Fan 2220 Temp 39
Chain 2 Fan 0 Temp 42
I have a honeywell blowing air on it. I only have one mining pool set up.
Beeping means it doesn't have an active internet connection.
It's wired in. The only thing I have to solve it, is a reboot. Is there a way where I can schedule it to reboot every 3 or 4 hours?
April 26, 2014, 12:05:59 PM
I caved. I just drilled holes, climbed in the top crawl space and ran cat6 to the other room. My next problem is, it stops mining after 30 mins (beeping sound).
Chain 1 Fan 2220 Temp 39
Chain 2 Fan 0 Temp 42
I have a honeywell blowing air on it. I only have one mining pool set up.
Chain 1 Fan 2220 Temp 39
Chain 2 Fan 0 Temp 42
I have a honeywell blowing air on it. I only have one mining pool set up.
Beeping means it doesn't have an active internet connection.
April 25, 2014, 10:28:38 PM
I caved. I just drilled holes, climbed in the top crawl space and ran cat6 to the other room. My next problem is, it stops mining after 30 mins (beeping sound).
Chain 1 Fan 2220 Temp 39
Chain 2 Fan 0 Temp 42
I have a honeywell blowing air on it. I only have one mining pool set up.
Chain 1 Fan 2220 Temp 39
Chain 2 Fan 0 Temp 42
I have a honeywell blowing air on it. I only have one mining pool set up.
April 25, 2014, 03:54:14 AM
I ran 2 s1 on wifi for over a week saw no difference in performance.
was experiencing drop outs initially but used a 30dbi high gain antenna and saw no difference between hardwired and wifi
setting up wifi is quite easy once you have setup the lan side and got that working, then hit the wifi and scan add your wireless network in and that should be it.
everything else should be configured on the WAN, and if you stuff it up, just hit the reset button and reconfigure.
I will say the WRT module is bit slow so don't expect it to start hashing on wifi instantly it could take a good 5 minutes before starting.
when adding wifi DO NOT change any the IP settings on wifi, that's all done on the wan not wifi section.
was experiencing drop outs initially but used a 30dbi high gain antenna and saw no difference between hardwired and wifi
setting up wifi is quite easy once you have setup the lan side and got that working, then hit the wifi and scan add your wireless network in and that should be it.
everything else should be configured on the WAN, and if you stuff it up, just hit the reset button and reconfigure.
I will say the WRT module is bit slow so don't expect it to start hashing on wifi instantly it could take a good 5 minutes before starting.
when adding wifi DO NOT change any the IP settings on wifi, that's all done on the wan not wifi section.
April 24, 2014, 10:28:13 PM
Go to network-firewall and try change some settings, but it's very difficult to do it,
I can manage it from wifi, but i don't know what i've done exactly !
I can manage it from wifi, but i don't know what i've done exactly !
April 24, 2014, 09:41:04 PM
Dont try using the wifi built in others have suggested adding a wifi bridge that seem to work. I don't know much about those settings but the lan is easy and these run like champs.
April 24, 2014, 09:04:11 PM
I have my ant miner s1 in the other room. when i configure it, i use the LAN to put all the setup info in. I was able to get a static WAN IP on my network, and while tethered, I configured the WWAN. I set a static IP for that and before I unplugged it, I could see my router recognize it as a wireless device. I proceed to do a software reboot on the miner, wait 3-5 mins, but when I go to my router, I do not see my static assigned wifi address (or even the mac address to the WWAN) look in my router for attached devices and I see the wireless static IP. I attempt to use that IP to connect to the interface, but it can never make a connection. I'd like to manage this via wifi. Is there something I'm missing? The manual just simply states how to scan for wifi, and add it... not so much how to manage the unit wirelessly.
Jump to: