Bitcoin Forum>Bitcoin>Mining>Mining support
Author

Topic: Antminer S17+ not hashing (Read 167 times)

Astra2000
newbie
Activity: 10
Merit: 2
Antminer S17+ not hashing
June 09, 2021, 01:30:25 PM
#14
Alright,

I had send the two hashboards for repair, and I replace the fan (works fine now).

At the moment I'm hashing with only one board ( 22Ths).


I will leave it like this until the boards came back.

Thanks to all
Astra2000
newbie
Activity: 10
Merit: 2
Re: Antminer S17+ not hashing
June 08, 2021, 01:41:47 PM
#13
Quote from: mikeywith on June 06, 2021, 04:04:36 PM
Quote from: Astra2000 on June 05, 2021, 07:59:47 AM
for some weird reason, all the fans are working now.

Not for a weird reason, the reason is you likely plugged both cables, right?

Quote
I have take out the good hashboard and insert the 2 bad ones. here is the log:

You are using a different firmware which refers to the kernel log as something else, whatever you posted here is not the "kernel log" we need even if it says so on the custom firmware, look for sys/system logs and post those.

Not really, the fan was not moving with both cables but I help the fan start rotating the fan with a screw driver...
I'm using BraiinOs
I will do some more tests tomorrow, and I will post later on Smiley
thierry4wd
sr. member
Activity: 446
Merit: 347
Re: Antminer S17+ not hashing
June 07, 2021, 12:15:13 PM
#12
yes, need stock firmware for diag (or mine, stock based too), is more easy to see the real problem Smiley
mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
Re: Antminer S17+ not hashing
June 06, 2021, 04:04:36 PM
#11
Quote from: Astra2000 on June 05, 2021, 07:59:47 AM
for some weird reason, all the fans are working now.

Not for a weird reason, the reason is you likely plugged both cables, right?

Quote
I have take out the good hashboard and insert the 2 bad ones. here is the log:

You are using a different firmware which refers to the kernel log as something else, whatever you posted here is not the "kernel log" we need even if it says so on the custom firmware, look for sys/system logs and post those.
Astra2000
newbie
Activity: 10
Merit: 2
Re: Antminer S17+ not hashing
June 06, 2021, 09:02:25 AM
#10
I have take out the good hashboard and insert the 2 bad ones. here is the log:

Code:
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 223608K/262144K available (5572K kernel code, 204K rwdata, 1844K rodata, 260K init, 221K bss, 22152K reserved, 16384K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0746524   (7418 kB)
[    0.000000]       .init : 0xc0747000 - 0xc0788000   ( 260 kB)
[    0.000000]       .data : 0xc0788000 - 0xc07bb2a0   ( 205 kB)
[    0.000000]        .bss : 0xc07bb2a0 - 0xc07f29c4   ( 222 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] slcr mapped to d0800000
[    0.000000] L2C: platform modifies aux control register: 0x02060000 -> 0x32460000
[    0.000000] L2C: DT/platform modifies aux control register: 0x02060000 -> 0x32460000
[    0.000000] L2C-310 erratum 769419 enabled
[    0.000000] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 cache controller enabled, 8 ways, 512 kB
[    0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x46460001
[    0.000000] zynq_clock_init: clkc starts at d0800100
[    0.000000] Zynq clock init
[    0.000011] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
[    0.000035] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
[    0.000137] clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
[    0.000168] timer #0 at d0808000, irq=17
[    0.000536] Console: colour dummy device 80x30
[    0.000558] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.090311] pid_max: default: 32768 minimum: 301
[    0.090415] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090429] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090929] CPU: Testing write buffer coherency: ok
[    0.091134] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.091227] Setting up static identity map for 0x8280 - 0x82d8
[    0.260299] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.260373] Brought up 2 CPUs
[    0.260392] SMP: Total of 2 processors activated (2664.03 BogoMIPS).
[    0.260400] CPU: All CPU(s) started in SVC mode.
[    0.265052] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.265481] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.266387] pinctrl core: initialized pinctrl subsystem
[    0.267730] NET: Registered protocol family 16
[    0.269760] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.300301] cpuidle: using governor ladder
[    0.320278] cpuidle: using governor menu
[    0.333070] zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xd0880000
[    0.333499] zynq-pinctrl 700.pinctrl: zynq pinctrl initialized
[    0.381125] GPIO IRQ not connected
[    0.381143] XGpio: /amba_pl/gpio@41200000: registered, base is 902
[    0.381324] GPIO IRQ not connected
[    0.381335] XGpio: /amba_pl/gpio@41210000: registered, base is 897
[    0.381559] XGpio: /amba_pl/gpio@41220000: registered, base is 895
[    0.382354] vgaarb: loaded
[    0.382739] SCSI subsystem initialized
[    0.383092] usbcore: registered new interface driver usbfs
[    0.383177] usbcore: registered new interface driver hub
[    0.383286] usbcore: registered new device driver usb
[    0.384030] i2c-gpio amba_pl:i2c-psu: using pins 895 (SDA) and 896 (SCL)
[    0.384100] media: Linux media interface: v0.10
[    0.384177] Linux video capture interface: v2.00
[    0.384257] pps_core: LinuxPPS API ver. 1 registered
[    0.384268] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.384312] PTP clock support registered
[    0.384405] EDAC MC: Ver: 3.0.0
[    0.386428] Advanced Linux Sound Architecture Driver Initialized.
[    0.387673] clocksource: Switched to clocksource arm_global_timer
[    0.396391] NET: Registered protocol family 2
[    0.397168] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.397210] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.397259] TCP: Hash tables configured (established 2048 bind 2048)
[    0.397316] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.397349] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.397553] NET: Registered protocol family 1
[    0.408033] RPC: Registered named UNIX socket transport module.
[    0.408047] RPC: Registered udp transport module.
[    0.408055] RPC: Registered tcp transport module.
[    0.408063] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.408097] PCI: CLS 0 bytes, default 64
[    0.408346] Trying to unpack rootfs image as initramfs...
[    0.408610] rootfs image is not initramfs (junk in compressed archive); looks like an initrd
[    0.458474] Freeing initrd memory: 11536K (c74bc000 - c8000000)
[    0.459870] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.470750] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.483207] io scheduler noop registered
[    0.483230] io scheduler deadline registered
[    0.483283] io scheduler cfq registered (default)
[    0.485285] dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330
[    0.485306] dma-pl330 f8003000.dmac: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.486025] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.487379] e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 143, base_baud = 6249999) is a xuartps
[    1.147146] console [ttyPS0] enabled
[    1.151308] xdevcfg f8007000.devcfg: ioremap 0xf8007000 to d0826000
[    1.158038] [drm] Initialized drm 1.1.0 20060810
[    1.173284] brd: module loaded
[    1.182368] loop: module loaded
[    1.188455] CAN device driver interface
[    1.193624] libphy: MACB_mii_bus: probed
[    1.277804] macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 145 (94:7b:19:bb:3e:1b)
[    1.287706] macb e000b000.ethernet eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
[    1.298928] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.304677] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.316478] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.322965] ehci-pci: EHCI PCI platform driver
[    1.327598] usbcore: registered new interface driver usb-storage
[    1.335152] mousedev: PS/2 mouse device common for all mice
[    1.341165] i2c /dev entries driver
[    1.348458] EDAC MC: ECC not enabled
[    1.352209] Xilinx Zynq CpuIdle Driver started
[    1.356886] sdhci: Secure Digital Host Controller Interface driver
[    1.363097] sdhci: Copyright(c) Pierre Ossman
[    1.367377] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.373385] sdhci-arasan e0100000.mmc: No vmmc regulator found
[    1.379210] sdhci-arasan e0100000.mmc: No vqmmc regulator found
[    1.417698] mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA
[    1.429640] ledtrig-cpu: registered to indicate activity on CPUs
[    1.435979] usbcore: registered new interface driver usbhid
[    1.441526] usbhid: USB HID core driver
[    1.454407] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.460715] nand: Micron MT29F2G08ABAEAWP
[    1.464684] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.472264] nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
[    1.483733] Bad block table found at page 131008, version 0x01
[    1.489979] Bad block table found at page 130944, version 0x01
[    1.496041] 11 cmdlinepart partitions found on MTD device pl35x-nand
[    1.502329] Creating 11 MTD partitions on "pl35x-nand":
[    1.507516] 0x000000000000-0x000000080000 : "boot"
[    1.513382] 0x000000080000-0x000000300000 : "uboot"
[    1.519236] 0x000000300000-0x000000500000 : "fpga1"
[    1.524970] 0x000000500000-0x000000700000 : "fpga2"
[    1.530752] 0x000000700000-0x000000780000 : "uboot_env"
[    1.530869] mmc0: new high speed SDHC card at address e624
[    1.542377] 0x000000780000-0x000000800000 : "miner_cfg"
[    1.548028] mmcblk0: mmc0:e624 AFGCC 14.8 GiB 
[    1.555216]  mmcblk0: p1 p2
[    1.558751] 0x000000800000-0x000001e00000 : "recovery"
[    1.565014] 0x000001e00000-0x000007d00000 : "firmware1"
[    1.581821] 0x000007d00000-0x00000dc00000 : "firmware2"
[    1.588555] 0x00000dc00000-0x000010000000 : "factory"
[    1.594699] 0x000004800000-0x000005000000 : "antminer_configs"
[    1.604701] nf_conntrack version 0.5.0 (3930 buckets, 15720 max)
[    1.612598] NET: Registered protocol family 10
[    1.618299] sit: IPv6 over IPv4 tunneling driver
[    1.623730] NET: Registered protocol family 17
[    1.628273] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.640833] can: controller area network core (rev 20120528 abi 9)
[    1.647020] NET: Registered protocol family 29
[    1.651510] can: raw protocol (rev 20120528)
[    1.655707] can: broadcast manager protocol (rev 20120528 t)
[    1.661384] can: netlink gateway (rev 20130117) max_hops=1
[    1.667031] 8021q: 802.1Q VLAN Support v1.8
[    1.671573] Registering SWP/SWPB emulation handler
[    1.677894] hctosys: unable to open rtc device (rtc0)
[    1.687382] ALSA device list:
[    1.690323]   No soundcards found.
[    1.694095] RAMDISK: squashfs filesystem found at block 0
[    1.699466] RAMDISK: Loading 11533KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
[    1.999229] VFS: Mounted root (squashfs filesystem) readonly on device 1:0.
[    2.006446] Freeing unused kernel memory: 260K (c0747000 - c0788000)
[    2.421835] init: Console is alive
[    2.425332] init: - watchdog -
[    2.784479] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.866283] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.882521] init: - preinit -
[    3.213503] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[    3.228941] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    3.270646] EXT4-fs (mmcblk0p2): recovery complete
[    3.279927] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    3.340416] ubi0: attaching mtd10
[    3.344304] random: procd urandom read with 4 bits of entropy available
[    3.373136] ubi0: scanning is finished
[    3.381834] ubi0 error: vtbl_check: too large reserved_pebs 91, good PEBs 64
[    3.388831] ubi0 error: vtbl_check: volume table check failed: record 1, error 9
[    3.396176] Volume table record 1 dump:
[    3.400016] 	reserved_pebs   91
[    3.403119] 	alignment       1
[    3.406157] 	data_pad        0
[    3.409214] 	vol_type        1
[    3.412233] 	upd_marker      0
[    3.415270] 	name_len        6
[    3.418328] 	name            rootfs
[    3.421782] 	crc             0xb9a9f09
[    3.425685] ubi0 error: ubi_attach_mtd_dev: failed to attach mtd10, error -22
[    4.020665] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.277867] macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
[    5.285968] macb e000b000.ethernet eth0: link up (100/Full)
[    5.291561] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    7.208129] mount_root: rootdisk overlay filesystem has not been formatted yet
[    7.760844] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
[    8.262587] block: attempting to load /etc/config/fstab
[    8.322003] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: 
[    8.417855] mount_root: switched to extroot
[    8.428016] urandom-seed: Seeding with /etc/urandom.seed
[    8.504644] procd: - early -
[    8.507504] procd: - watchdog -
[    9.144270] procd: - watchdog -
[    9.147548] procd: - ubus -
[    9.306163] procd: - init -
[    9.307750] macb e000b000.ethernet eth0: link down
[    9.609301] kmodloader: loading kernel modules from /etc/modules.d/*
[    9.686735] tun: Universal TUN/TAP device driver, 1.6
[    9.691744] tun: (C) 1999-2004 Max Krasnyansky 
[    9.700885] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.713315] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.809238] xt_time: kernel timezone is -0000
[    9.819606] kmodloader: done loading kernel modules from /etc/modules.d/*
[   12.703229] device eth0 entered promiscuous mode
[   12.711389] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   13.307929] macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
[   13.316039] macb e000b000.ethernet eth0: link up (100/Full)
[   13.337757] br-lan: port 1(eth0) entered forwarding state
[   13.343122] br-lan: port 1(eth0) entered forwarding state
[   13.350382] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   13.562905] random: nonblocking pool is initialized
[   15.337808] br-lan: port 1(eth0) entered forwarding state
Astra2000
newbie
Activity: 10
Merit: 2
Re: Antminer S17+ not hashing
June 05, 2021, 08:08:03 AM
#9
Quote from: thierry4wd on June 05, 2021, 05:16:34 AM
hi, i repaire the PSUs , and i assure to you, the 3 fan is not on monitoring, so, if fan is dead, the psu still working ! Wink

for sure if PSU is good or not, needed full kernel log, send this after 5min running Wink

Thank you for your reply, I will give you the kernel log as soon I have some time, maybe tomorrow Smiley

-----EDIT------


Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.4.0-xilinx-g518c00cd977f-dirty (build@runner-pegegjka-project-312-concurrent-3) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3560-79f57e422d) ) #0 SMP PREEMPT Wed May 26 10:04:03 2021
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Antminer S17 Miner Control Board
[    0.000000] cma: Reserved 16 MiB at 0x0f000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 65536
[    0.000000] free_area_init_node: node 0, pgdat c07ba340, node_mem_map cedf0000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 12 pages/cpu @cedca000 s18944 r8192 d22016 u49152
[    0.000000] pcpu-alloc: s18944 r8192 d22016 u49152 alloc=12*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyPS0,115200 noinitrd ubi.mtd=7 ubi.block=0,1 root=/dev/ubiblock0_1 r rootfstype=squashfs rootwait mtdparts=pl35x-nand:512k(boot),2560k(uboot),2m(fpga1),2m(fpga2),512k(uboot_env),512k(miner_cfg),22m(recovery),95m(firmware1),95m(firmware2),36m(factory) earlyprintk
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 235148K/262144K available (5572K kernel code, 204K rwdata, 1844K rodata, 260K init, 221K bss, 10612K reserved, 16384K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0746524   (7418 kB)
[    0.000000]       .init : 0xc0747000 - 0xc0788000   ( 260 kB)
[    0.000000]       .data : 0xc0788000 - 0xc07bb2a0   ( 205 kB)
[    0.000000]        .bss : 0xc07bb2a0 - 0xc07f29c4   ( 222 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] slcr mapped to d0800000
[    0.000000] L2C: platform modifies aux control register: 0x02060000 -> 0x32460000
[    0.000000] L2C: DT/platform modifies aux control register: 0x02060000 -> 0x32460000
[    0.000000] L2C-310 erratum 769419 enabled
[    0.000000] L2C-310 enabling early BRESP for Cortex-A9
[    0.000000] L2C-310 full line of zeros enabled for Cortex-A9
[    0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled
[    0.000000] L2C-310 cache controller enabled, 8 ways, 512 kB
[    0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x46460001
[    0.000000] zynq_clock_init: clkc starts at d0800100
[    0.000000] Zynq clock init
[    0.000011] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
[    0.000036] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
[    0.000139] clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
[    0.000168] timer #0 at d0808000, irq=17
[    0.000537] Console: colour dummy device 80x30
[    0.000559] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.090310] pid_max: default: 32768 minimum: 301
[    0.090416] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090429] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090927] CPU: Testing write buffer coherency: ok
[    0.091134] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.091226] Setting up static identity map for 0x8280 - 0x82d8
[    0.260299] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.260374] Brought up 2 CPUs
[    0.260393] SMP: Total of 2 processors activated (2664.03 BogoMIPS).
[    0.260401] CPU: All CPU(s) started in SVC mode.
[    0.265212] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.265638] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.266547] pinctrl core: initialized pinctrl subsystem
[    0.267893] NET: Registered protocol family 16
[    0.269984] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.300413] cpuidle: using governor ladder
[    0.330284] cpuidle: using governor menu
[    0.343113] zynq-ocm f800c000.ocmc: ZYNQ OCM pool: 256 KiB @ 0xd0880000
[    0.343549] zynq-pinctrl 700.pinctrl: zynq pinctrl initialized
[    0.391794] GPIO IRQ not connected
[    0.391812] XGpio: /amba_pl/gpio@41200000: registered, base is 902
[    0.392001] GPIO IRQ not connected
[    0.392013] XGpio: /amba_pl/gpio@41210000: registered, base is 897
[    0.392258] XGpio: /amba_pl/gpio@41220000: registered, base is 895
[    0.393097] vgaarb: loaded
[    0.393547] SCSI subsystem initialized
[    0.393981] usbcore: registered new interface driver usbfs
[    0.394079] usbcore: registered new interface driver hub
[    0.394185] usbcore: registered new device driver usb
[    0.395015] i2c-gpio amba_pl:i2c-psu: using pins 895 (SDA) and 896 (SCL)
[    0.395090] media: Linux media interface: v0.10
[    0.395174] Linux video capture interface: v2.00
[    0.395255] pps_core: LinuxPPS API ver. 1 registered
[    0.395266] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.395311] PTP clock support registered
[    0.395416] EDAC MC: Ver: 3.0.0
[    0.396450] Advanced Linux Sound Architecture Driver Initialized.
[    0.397710] clocksource: Switched to clocksource arm_global_timer
[    0.406542] NET: Registered protocol family 2
[    0.407352] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.407394] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.407442] TCP: Hash tables configured (established 2048 bind 2048)
[    0.407494] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.407527] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.407767] NET: Registered protocol family 1
[    0.418210] RPC: Registered named UNIX socket transport module.
[    0.418224] RPC: Registered udp transport module.
[    0.418233] RPC: Registered tcp transport module.
[    0.418241] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.418273] PCI: CLS 0 bytes, default 64
[    0.419865] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.431699] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.434111] io scheduler noop registered
[    0.434134] io scheduler deadline registered
[    0.434188] io scheduler cfq registered (default)
[    0.436109] dma-pl330 f8003000.dmac: Loaded driver for PL330 DMAC-241330
[    0.436130] dma-pl330 f8003000.dmac: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.436875] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.438323] e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 143, base_baud = 6249999) is a xuartps
[    1.079899] console [ttyPS0] enabled
[    1.084062] xdevcfg f8007000.devcfg: ioremap 0xf8007000 to d0826000
[    1.090788] [drm] Initialized drm 1.1.0 20060810
[    1.106197] brd: module loaded
[    1.115305] loop: module loaded
[    1.121826] CAN device driver interface
[    1.127008] libphy: MACB_mii_bus: probed
[    1.207845] macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 145 (94:7b:19:bb:3e:1b)
[    1.217724] macb e000b000.ethernet eth0: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
[    1.228948] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[    1.234694] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    1.246187] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.252676] ehci-pci: EHCI PCI platform driver
[    1.257232] usbcore: registered new interface driver usb-storage
[    1.264730] mousedev: PS/2 mouse device common for all mice
[    1.270665] i2c /dev entries driver
[    1.278125] EDAC MC: ECC not enabled
[    1.281900] Xilinx Zynq CpuIdle Driver started
[    1.286641] sdhci: Secure Digital Host Controller Interface driver
[    1.292853] sdhci: Copyright(c) Pierre Ossman
[    1.297135] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.303157] sdhci-arasan e0100000.mmc: No vmmc regulator found
[    1.308974] sdhci-arasan e0100000.mmc: No vqmmc regulator found
[    1.347741] mmc0: SDHCI controller on e0100000.mmc [e0100000.mmc] using ADMA
[    1.355634] ledtrig-cpu: registered to indicate activity on CPUs
[    1.362164] usbcore: registered new interface driver usbhid
[    1.367655] usbhid: USB HID core driver
[    1.372458] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.378758] nand: Micron MT29F2G08ABAEAWP
[    1.382719] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.390295] nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
[    1.401762] Bad block table found at page 131008, version 0x01
[    1.407978] Bad block table found at page 130944, version 0x01
[    1.414033] 10 cmdlinepart partitions found on MTD device pl35x-nand
[    1.420331] Creating 10 MTD partitions on "pl35x-nand":
[    1.425513] 0x000000000000-0x000000080000 : "boot"
[    1.431323] 0x000000080000-0x000000300000 : "uboot"
[    1.447056] 0x000000300000-0x000000500000 : "fpga1"
[    1.452871] 0x000000500000-0x000000700000 : "fpga2"
[    1.458687] 0x000000700000-0x000000780000 : "uboot_env"
[    1.464815] 0x000000780000-0x000000800000 : "miner_cfg"
[    1.471033] 0x000000800000-0x000001e00000 : "recovery"
[    1.477231] 0x000001e00000-0x000007d00000 : "firmware1"
[    1.484053] 0x000007d00000-0x00000dc00000 : "firmware2"
[    1.490890] 0x00000dc00000-0x000010000000 : "factory"
[    1.509953] nf_conntrack version 0.5.0 (3930 buckets, 15720 max)
[    1.517763] NET: Registered protocol family 10
[    1.523406] sit: IPv6 over IPv4 tunneling driver
[    1.528763] NET: Registered protocol family 17
[    1.533180] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.545749] can: controller area network core (rev 20120528 abi 9)
[    1.551966] NET: Registered protocol family 29
[    1.556339] can: raw protocol (rev 20120528)
[    1.560611] can: broadcast manager protocol (rev 20120528 t)
[    1.566237] can: netlink gateway (rev 20130117) max_hops=1
[    1.571937] 8021q: 802.1Q VLAN Support v1.8
[    1.576435] Registering SWP/SWPB emulation handler
[    1.582706] ubi0: attaching mtd7
[    1.930485] ubi0: scanning is finished
[    1.941852] ubi0: attached mtd7 (name "firmware1", size 95 MiB)
[    1.947693] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.954549] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.961337] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.968285] ubi0: good PEBs: 760, bad PEBs: 0, corrupted PEBs: 0
[    1.974252] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    1.981474] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1484175833
[    1.990592] ubi0: available PEBs: 0, total reserved PEBs: 760, PEBs reserved for bad PEB handling: 40
[    1.999801] ubi0: background thread "ubi_bgt0d" started, PID 845
[    2.010759] block ubiblock0_1: created from ubi0:1(rootfs)
[    2.016186] hctosys: unable to open rtc device (rtc0)
[    2.025758] ALSA device list:
[    2.028688]   No soundcards found.
[    2.034704] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    2.042128] Freeing unused kernel memory: 260K (c0747000 - c0788000)
[    2.516568] init: Console is alive
[    2.520132] init: - watchdog -
[    2.923905] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.019565] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.028001] init: - preinit -
[    3.609392] random: jshn urandom read with 0 bits of entropy available
[    3.813364] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    5.227904] macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
[    5.236009] macb e000b000.ethernet eth0: link up (100/Full)
[    5.241600] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[    6.977790] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 920
[    7.001934] UBIFS (ubi0:2): recovery needed
[    7.074073] UBIFS (ubi0:2): recovery completed
[    7.078555] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[    7.086303] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.096219] UBIFS (ubi0:2): FS size: 75169792 bytes (71 MiB, 592 LEBs), journal size 3809280 bytes (3 MiB, 30 LEBs)
[    7.106626] UBIFS (ubi0:2): reserved for root: 3550454 bytes (3467 KiB)
[    7.113235] UBIFS (ubi0:2): media format: w4/r0 (latest is w4/r0), UUID E3ED6C11-1B19-4D4F-AFE1-DBC9417B8A7D, small LPT model
[    7.126933] mount_root: switching to ubifs overlay
[    7.139665] urandom-seed: Seeding with /etc/urandom.seed
[    7.263052] procd: - early -
[    7.265910] procd: - watchdog -
[    7.911428] procd: - watchdog -
[    7.914709] procd: - ubus -
[    8.072287] procd: - init -
[    8.237779] macb e000b000.ethernet eth0: link down
[    8.456780] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.465911] tun: Universal TUN/TAP device driver, 1.6
[    8.470913] tun: (C) 1999-2004 Max Krasnyansky 
[    8.480255] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    8.493175] ip_tables: (C) 2000-2006 Netfilter Core Team
[    8.619344] xt_time: kernel timezone is -0000
[    8.629857] kmodloader: done loading kernel modules from /etc/modules.d/*
[   11.518286] device eth0 entered promiscuous mode
[   11.527353] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   11.664909] Start post-upgrade process...
[   12.237954] macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
[   12.246058] macb e000b000.ethernet eth0: link up (100/Full)
[   12.262003] br-lan: port 1(eth0) entered forwarding state
[   12.267380] br-lan: port 1(eth0) entered forwarding state
[   12.283250] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   12.664890] random: nonblocking pool is initialized
[   14.257754] br-lan: port 1(eth0) entered forwarding state


https://i.ibb.co/4scdDVz/Captura-de-ecr-2021-06-05-215758.png
Astra2000
newbie
Activity: 10
Merit: 2
Re: Antminer S17+ not hashing
June 05, 2021, 07:59:47 AM
#8
Quote from: mikeywith on June 04, 2021, 02:01:19 PM
Quote from: Astra2000 on June 04, 2021, 01:22:39 AM
Hi, I made a new video testing the fan

https://youtu.be/Q47gvNuH-SY

Maybe are both faulty ( PSU and Fan )

Gave you 2 merit points for the efforts, it's great to see more video content in the forum.

Can you re-do the same test but with the TWO power cords plugged in?

Thanks Smiley

for some weird reason, all the fans are working now.
I have only one hashboard attached because the other 2 have the heatsinks falling :/

https://www.youtube.com/watch?v=X3EQ-b2E6Xs


https://i.ibb.co/Qfv7qMY/10.jpg
https://i.ibb.co/TPs15Fr/11.jpg
https://i.ibb.co/MkNykKJ/12.jpg
https://i.ibb.co/3WT1z4F/13.jpg
https://i.ibb.co/R35GF2K/14.jpg

are the hashboards dead ?
thierry4wd
sr. member
Activity: 446
Merit: 347
Re: Antminer S17+ not hashing
June 05, 2021, 05:16:34 AM
#7
hi, i repaire the PSUs , and i assure to you, the 3 fan is not on monitoring, so, if fan is dead, the psu still working ! Wink

for sure if PSU is good or not, needed full kernel log, send this after 5min running Wink
mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
Re: Antminer S17+ not hashing
June 04, 2021, 02:01:19 PM
#6
Quote from: Astra2000 on June 04, 2021, 01:22:39 AM
Hi, I made a new video testing the fan

https://youtu.be/Q47gvNuH-SY

Maybe are both faulty ( PSU and Fan )

Gave you 2 merit points for the efforts, it's great to see more video content in the forum.

Can you re-do the same test but with the TWO power cords plugged in?
Astra2000
newbie
Activity: 10
Merit: 2
Re: Antminer S17+ not hashing
June 04, 2021, 01:22:39 AM
#5
Hi, I made a new video testing the fan

https://youtu.be/Q47gvNuH-SY

Maybe are both faulty ( PSU and Fan )
mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
Re: Antminer S17+ not hashing
June 03, 2021, 08:35:35 PM
#4
Quote from: Astra2000 on June 03, 2021, 11:29:58 AM
https://youtu.be/fJE88E8Tn8c

I have some serious doubts about your way of troubleshooting the PSU, it's a bit sophisticated and far from the normal PSUs, this could still be a bad fan or a faulty fan connector and not a dead PSU, try to use the fan from the other rail and make sure you plug both cables while testing.
Astra2000
newbie
Activity: 10
Merit: 2
Re: Antminer S17+ not hashing
June 03, 2021, 11:29:58 AM
#3
Hi, thanks for your reply


I just found odd, that I connect one Hashboard alone and works, and if I change the Hashboard to one of the other two they just won't start.

btw I have check the PSU and one fan is not working :/

I have order a new one, maybe it works afterwords.

https://www.aliexpress.com/item/4000204031724.html?spm=a2g0s.9042311.0.0.2612b90aKD5Zw9




-----------------------------EDIT-----------------------------

Ok, I have check the PSU and the problem is not the fan, but yes the PSU

https://youtu.be/fJE88E8Tn8c
mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
Re: Antminer S17+ not hashing
June 02, 2021, 07:19:49 PM
#2
Code:
[quote author=Astra2000 link=topic=5341278.msg57134443#msg57134443 date=1622547696]
2021-05-29 07:59:29 driver-btm-api.c:2382:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-05-29 07:59:29 power_api.c:186:power_off: init gpio907


The miner should work just fine without the heatsinks as long as the heatsink isn't shorting the other once, it will get to the point where you can feel the heat coming out from the miner but then it will show a temp-error and stop, so you don't really need to stick that heatsink just for testing purposes.

The kernel log is not complete, after the 30s sleep which usually takes a bit longer than 30 seconds, it should start testing the chips on all the connected chains, so allow more time and then post the rest of the following log because that part is what actually matters.

However, at first glance, it seems like you might have a faulty PSU, there are a few things to do to troubleshoot it but I rather see the complete kernel logs from the original firmware before arriving at conclusions.

Astra2000
newbie
Activity: 10
Merit: 2
Re: Antminer S17+ not hashing
June 01, 2021, 06:41:36 AM
#1
Hi there,

I bought my first and last Antminer S17+ 70Ths

I get my miner (used) last Friday and as soon I unpacked and got a inspection on the boards, the heatsinks fall down.
 https://ibb.co/5s9q8VY


https://i.ibb.co/rwLr4RG/5.jpg
https://i.ibb.co/72K5Bcd/6.jpg
After some research I glue the heatsinks with thermal glue for heatsinks and start the miner, sadly both boards don't hash anymore.

Still I think maybe is not only the heatsinks problem, because I see some NAND errors on the Kernel Log
Code:

Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
  Normal zone: 480 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc: [0] 0 [0] 1 
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 60960
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203432K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25944K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xcf800000 - 0xff800000   ( 768 MB)
    lowmem  : 0xc0000000 - 0xcf000000   ( 240 MB)
    pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
    modules : 0xbf000000 - 0xbfe00000   (  14 MB)
      .text : 0xc0008000 - 0xc090c424   (9234 kB)
      .init : 0xc0a00000 - 0xc0b00000   (1024 kB)
      .data : 0xc0b00000 - 0xc0b39fe0   ( 232 kB)
       .bss : 0xc0b39fe0 - 0xc0b71c28   ( 224 kB)
Preemptible hierarchical RCU implementation.
	Build-time adjustment of leaf fanout to 32.
	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12904K (cce67000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
  No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 16/6, WL threshold: 4096, image sequence number: 262741923
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): recovery needed
UBIFS (ubi0:0): recovery completed
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID A9E8BDA4-70DE-45D9-83BE-2DD9F129C0C6, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 2064/578, WL threshold: 4096, image sequence number: 3563076859
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): recovery needed
UBIFS (ubi1:0): recovery completed
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID A21581E4-693A-4BBF-A66A-FCE5ACD2EF7F, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
2021-05-29 07:58:57 driver-btm-api.c:779:init_freq_mode: This is scan-user version
2021-05-29 07:58:57 driver-btm-api.c:2451:bitmain_soc_init: opt_multi_version     = 1
2021-05-29 07:58:57 driver-btm-api.c:2452:bitmain_soc_init: opt_bitmain_ab        = 1
2021-05-29 07:58:57 driver-btm-api.c:2453:bitmain_soc_init: opt_bitmain_work_mode = 0
2021-05-29 07:58:57 driver-btm-api.c:2454:bitmain_soc_init: Miner compile time: Tue Jun  2 10:31:07 CST 2020 type: Antminer S17+
2021-05-29 07:58:57 driver-btm-api.c:2455:bitmain_soc_init: commit version: 1ca50a5 2020-06-01 18:51:22, build by: lol 2020-06-02 10:37:21
2021-05-29 07:58:57 driver-btm-api.c:2083:show_sn: len:16, 802425c05710481c
2021-05-29 07:58:57 driver-btm-api.c:2461:bitmain_soc_init: show sn return 1
2021-05-29 07:58:57 driver-btm-api.c:2103:handle_sn_for_factory_mode: show sn return 1
2021-05-29 07:58:57 driver-btm-api.c:2141:handle_sn_for_factory_mode: read sn success, 802425c05710481c
2021-05-29 07:58:57 fan.c:284:front_fan_power_on: Note: front fan is power on!
2021-05-29 07:58:57 fan.c:296:rear_fan_power_on: Note: rear fan is power on!
2021-05-29 07:58:57 driver-btm-api.c:1314:miner_device_init: Detect 256MB control board of XILINX
2021-05-29 07:58:57 driver-btm-api.c:1255:init_fan_parameter: fan_eft : 0  fan_pwm : 0
2021-05-29 07:59:03 driver-btm-api.c:1239:init_miner_version: miner ID : 802425c05710481c
2021-05-29 07:59:03 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-05-29 07:59:09 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-05-29 07:59:09 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-05-29 07:59:09 driver-btm-api.c:837:get_product_id: product_id[3] = 0
2021-05-29 07:59:09 driver-btm-api.c:2234:update_conf_by_power_feedback: Power feedback is disabled
2021-05-29 07:59:09 driver-btm-api.c:2202:get_calibration_voltage: calibration voltage flag is error data.
2021-05-29 07:59:09 driver-btm-api.c:2268:update_conf_by_power_feedback: Note: no calibration voltage, default diff = 0
2021-05-29 07:59:09 frequency.c:1457:adjust_higer_max_vol_table: adjust_higer_max_vol_table, adjust_vol = 0
2021-05-29 07:59:09 thread.c:1363:create_read_nonce_reg_thread: create thread
2021-05-29 07:59:15 driver-btm-api.c:1239:init_miner_version: miner ID : 802425c05710481c
2021-05-29 07:59:15 driver-btm-api.c:1245:init_miner_version: FPGA Version = 0xB023
2021-05-29 07:59:20 driver-btm-api.c:837:get_product_id: product_id[1] = 0
2021-05-29 07:59:20 driver-btm-api.c:837:get_product_id: product_id[2] = 0
2021-05-29 07:59:20 driver-btm-api.c:837:get_product_id: product_id[3] = 0
2021-05-29 07:59:20 driver-btm-api.c:792:_set_project_type: project:0
2021-05-29 07:59:20 driver-btm-api.c:813:_set_project_type: Project type: Antminer S17+
2021-05-29 07:59:20 driver-btm-api.c:824:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2021-05-29 07:59:20 driver-btm-api.c:825:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2021-05-29 07:59:20 driver-btm-api.c:824:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2021-05-29 07:59:20 driver-btm-api.c:825:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2021-05-29 07:59:20 driver-btm-api.c:824:dump_pcb_bom_version: Chain [3] PCB Version: 0x0100
2021-05-29 07:59:20 driver-btm-api.c:825:dump_pcb_bom_version: Chain [3] BOM Version: 0x0100
2021-05-29 07:59:20 driver-btm-api.c:2372:bitmain_board_init: Fan check passed.
2021-05-29 07:59:21 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2021-05-29 07:59:23 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
2021-05-29 07:59:24 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2021-05-29 07:59:26 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2021-05-29 07:59:27 board.c:36:jump_and_app_check_restore_pic: chain[3] PIC jump to app
2021-05-29 07:59:29 board.c:40:jump_and_app_check_restore_pic: Check chain[3] PIC fw version=0x88
2021-05-29 07:59:29 thread.c:1358:create_pic_heart_beat_thread: create thread
2021-05-29 07:59:29 power_api.c:213:power_init: Power init:
2021-05-29 07:59:29 power_api.c:214:power_init: current_voltage_raw = 0
2021-05-29 07:59:29 power_api.c:215:power_init: highest_voltage_raw = 2100
2021-05-29 07:59:29 power_api.c:216:power_init: working_voltage_raw = 1950
2021-05-29 07:59:29 power_api.c:217:power_init: higher_voltage_raw  = 2040
2021-05-29 07:59:29 power_api.c:218:power_init: check_asic_voltage_raw  = 2100
2021-05-29 07:59:29 driver-btm-api.c:2382:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2021-05-29 07:59:29 power_api.c:186:power_off: init gpio907




On this image with original Bitmain FW no hashes on all the 3 boards:
https://ibb.co/bK3nsWz
https://ibb.co/3WW2nvk


After that I install BraiinOS and 1 board hashes and 2 don't.


What can I do?

Any help will very appreciated


Thanks in advanced
Bitcoin Forum>Bitcoin>Mining>Mining support
Jump to: