Topic: Antminer S9 FAN stop, start, stop, start for 500 rpm (Read 241 times)
This is strange, because I already wrote 2 times that is was hardware fault of fan, so after replacement all is ok, so I won't flash it, no reason.
Can you post the kernel.log here and let me review the logs and put it inside the code sample below.
Hope that you check the link that I posted above it includes how to modify the fan speed then set the fan speed 75% or lower.
If not your fan might be defective.
Moderator's note: This post was edited by frodocooper to remove an unnecessary quote.
Code:
Copy paste your codes here
Hope that you check the link that I posted above it includes how to modify the fan speed then set the fan speed 75% or lower.
If not your fan might be defective.
Moderator's note: This post was edited by frodocooper to remove an unnecessary quote.
Did you try to reflash it with new firmware? Or hard reset it 2 times?
If this still didn't work you can try to modify the fan speed maybe you just need to adjust it and decrease or increase the speed of your fan.
I found a solution for modifying the fan speed and frequency you can try this method.
https://bitcointalksearch.org/topic/solution-for-antminer-s9-fans-speed-up-down-every-20-seconds-2690140
Open the images 1 by 1 and edit the fan speed.
Test your miner every time you change the fan speed if there are no changes maybe your fan is not compatible with your miner. So make sure it's compatible on your miner.
If this still didn't work you can try to modify the fan speed maybe you just need to adjust it and decrease or increase the speed of your fan.
I found a solution for modifying the fan speed and frequency you can try this method.
https://bitcointalksearch.org/topic/solution-for-antminer-s9-fans-speed-up-down-every-20-seconds-2690140
Open the images 1 by 1 and edit the fan speed.
Test your miner every time you change the fan speed if there are no changes maybe your fan is not compatible with your miner. So make sure it's compatible on your miner.
I did not try flash it, because as I wrote, after using fan from another antminer it is working ok.
Make sure that the fan you are trying to use has the blue pwm fan cable on the end, some versions of fan QFR1212GHE have this cable in one of the middle sockets.
it was black red yellow blue. in some old QFR1212GHE datasheet I read that yellow is PWM so i tried swap yellow and blue, it again not work, with different error in kernel.log - can't set fan speed, or something like that. Still I do not understand why? the QFR1212GHE is not working? it's on bitmain's web site in photo as spare part. Original fan is Martech DF1203812B2UN
Ok it was defective fan, fan from other antminer is working fine.
Question: fans are incompatible for Antminer, even if the fan is standard 6000 rpm 2.7A ? As I have QFR1212GHE, I got model number from picture on bitmain's web site, but this fan is not working. It show 30000 rpm and then 0 rpm.
thanks
Question: fans are incompatible for Antminer, even if the fan is standard 6000 rpm 2.7A ? As I have QFR1212GHE, I got model number from picture on bitmain's web site, but this fan is not working. It show 30000 rpm and then 0 rpm.
thanks
Did you try to reflash it with new firmware? Or hard reset it 2 times?
If this still didn't work you can try to modify the fan speed maybe you just need to adjust it and decrease or increase the speed of your fan.
I found a solution for modifying the fan speed and frequency you can try this method.
https://bitcointalksearch.org/topic/solution-for-antminer-s9-fans-speed-up-down-every-20-seconds-2690140
Open the images 1 by 1 and edit the fan speed.
Test your miner every time you change the fan speed if there are no changes maybe your fan is not compatible with your miner. So make sure it's compatible on your miner.
Make sure that the fan you are trying to use has the blue pwm fan cable on the end, some versions of fan QFR1212GHE have this cable in one of the middle sockets.
Ok it was defective fan, fan from other antminer is working fine.
Question: fans are incompatible for Antminer, even if the fan is standard 6000 rpm 2.7A ? As I have QFR1212GHE, I got model number from picture on bitmain's web site, but this fan is not working. It show 30000 rpm and then 0 rpm.
thanks
Question: fans are incompatible for Antminer, even if the fan is standard 6000 rpm 2.7A ? As I have QFR1212GHE, I got model number from picture on bitmain's web site, but this fan is not working. It show 30000 rpm and then 0 rpm.
thanks
Your fan couldn't detect properly that is why your miner stops.
Put back the old fan and try to perform a hard reset first or reflash it with other firmware before you are going to hardware.
Anyway, to perform a hard reset
Follow this guide https://enforum.bitmain.com/bbs/topics/3957
If hard reset won't work then do reflash your miner, you can download the firmware here https://shop.bitmain.com/support.htm
Put back the old fan and try to perform a hard reset first or reflash it with other firmware before you are going to hardware.
Anyway, to perform a hard reset
Follow this guide https://enforum.bitmain.com/bbs/topics/3957
If hard reset won't work then do reflash your miner, you can download the firmware here https://shop.bitmain.com/support.htm
Hi
antminer S9 and fan on it periodically stop and starts, about 5 seconds go and stop 1 second, then 5 seconds go etc.
On web it is showing it has from 300 to 700 rpm.
I replaced it with new fan QFR1212GHE, after that web is showing fan has 30000 rpm (yes 30000) and then 0 rpm and miner stops at all.
What is wrong here, fan or control board? Is my replacement fan QFR1212GHE wrong as replacement for Antminer S9?
thanks
antminer S9 and fan on it periodically stop and starts, about 5 seconds go and stop 1 second, then 5 seconds go etc.
On web it is showing it has from 300 to 700 rpm.
I replaced it with new fan QFR1212GHE, after that web is showing fan has 30000 rpm (yes 30000) and then 0 rpm and miner stops at all.
What is wrong here, fan or control board? Is my replacement fan QFR1212GHE wrong as replacement for Antminer S9?
thanks
Jump to: