Many issues can be solved by flashing a custom firmware, updating to the last stock version should be your LAST resort, I believe the "2019-08-08" version can still be unlocked, so do check Asic.to and AwsomeMiner for that.
The kernel log suggests that all 3 hash boards are dead
1st hashboard
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
2nd hashboard
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
3rd hashboard
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
This, in a nutshell, suggests that your miner is completely DEAD, however, the kernel log can only tell you so much, other reasons such as a bad PSU or/and bad control board can cause the same issue.
There is a ton of troubleshooting that you have to do, start with the following:
1- Replace the PSU.
2- Flash a different firmware.
Topic: Antminer S9 not hashing (Read 193 times)
According to your logs, it seems a fan issue if you follow the sticky thread as suggested above and you can't still solve the issue try this below.
Try to clean t(Male and female)connectors of both control board and PSU with brush(If full of rust add some thinner) then reattach them back to your control board.
If not, you might need to replace the fan that you know working.
Try to clean t(Male and female)connectors of both control board and PSU with brush(If full of rust add some thinner) then reattach them back to your control board.
If not, you might need to replace the fan that you know working.
First try reading pinned messages like this one that details the most common problems. If no joy there, look over the existing posts. Your question has been asked a gazillion times here in nearly as many posts. Odds are you will find the answer has already been posted.
Kudos for knowing to how to post the logs correctly!
Kudos for knowing to how to post the logs correctly!
My S9 is using the newest firmware from the Bitmain website https://service.bitmain.com/support/download?product=Antminer%20S9
It had run well for one or two months. Then I turned it off for a few months. However, at the moment, the problem is that it is not hashing. Pool connection seems OK as I see the Status "Alive" in the "Miner Status" tab.
I tried to reset the miner using the "IP Reporter" button but no luck.
Below is Kernel Log:
It had run well for one or two months. Then I turned it off for a few months. However, at the moment, the problem is that it is not hashing. Pool connection seems OK as I see the Status "Alive" in the "Miner Status" tab.
I tried to reset the miner using the "IP Reporter" button but no luck.
Below is Kernel Log:
Code:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 27800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map e6fd8000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 496 pages used for memmap
[ 0.000000] HighMem zone: 63488 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256528
[ 0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 884108K/1032192K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 148084K reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06da8ac (6987 kB)
[ 0.000000] .init : 0xc06db000 - 0xc070e380 ( 205 kB)
[ 0.000000] .data : 0xc0710000 - 0xc0757138 ( 285 kB)
[ 0.000000] .bss : 0xc0757144 - 0xc0797bfc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to f0004000
[ 0.000000] zynq_clock_init: clkc starts at f0004100
[ 0.000000] Zynq clock init
[ 0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000293] ps7-ttc #0 at f0006000, irq=43
[ 0.000594] Console: colour dummy device 80x30
[ 0.000630] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[ 0.090243] pid_max: default: 32768 minimum: 301
[ 0.090453] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.090475] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.092629] CPU: Testing write buffer coherency: ok
[ 0.092952] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.093009] Setting up static identity map for 0x4cb118 - 0x4cb170
[ 0.093229] L310 cache controller enabled
[ 0.093250] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.170988] CPU1: Booted secondary processor
[ 0.260220] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.260348] Brought up 2 CPUs
[ 0.260368] SMP: Total of 2 processors activated.
[ 0.260376] CPU: All CPU(s) started in SVC mode.
[ 0.261051] devtmpfs: initialized
[ 0.263464] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.264652] regulator-dummy: no parameters
[ 0.271509] NET: Registered protocol family 16
[ 0.273784] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.276038] cpuidle: using governor ladder
[ 0.276051] cpuidle: using governor menu
[ 0.283416] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.284920] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.284934] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.285043] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[ 0.306625] bio: create slab at 0
[ 0.308018] vgaarb: loaded
[ 0.308737] SCSI subsystem initialized
[ 0.309607] usbcore: registered new interface driver usbfs
[ 0.309793] usbcore: registered new interface driver hub
[ 0.310018] usbcore: registered new device driver usb
[ 0.310682] media: Linux media interface: v0.10
[ 0.310838] Linux video capture interface: v2.00
[ 0.311442] pps_core: LinuxPPS API ver. 1 registered
[ 0.311454] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.311588] PTP clock support registered
[ 0.311933] EDAC MC: Ver: 3.0.0
[ 0.313121] Advanced Linux Sound Architecture Driver Initialized.
[ 0.315846] DMA-API: preallocated 4096 debug entries
[ 0.315858] DMA-API: debugging enabled by kernel config
[ 0.315928] Switched to clocksource arm_global_timer
[ 0.336124] NET: Registered protocol family 2
[ 0.336778] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.336872] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.337031] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.337095] TCP: reno registered
[ 0.337111] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.337160] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.337412] NET: Registered protocol family 1
[ 0.337746] RPC: Registered named UNIX socket transport module.
[ 0.337758] RPC: Registered udp transport module.
[ 0.337767] RPC: Registered tcp transport module.
[ 0.337775] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.337786] PCI: CLS 0 bytes, default 64
[ 0.338210] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.340200] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.341568] bounce pool size: 64 pages
[ 0.342437] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.342641] msgmni has been set to 1486
[ 0.343395] io scheduler noop registered
[ 0.343409] io scheduler deadline registered
[ 0.343449] io scheduler cfq registered (default)
[ 0.355673] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.355693] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.478687] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.050741] console [ttyPS0] enabled
[ 1.054981] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[ 1.062587] [drm] Initialized drm 1.1.0 20060810
[ 1.079562] brd: module loaded
[ 1.088950] loop: module loaded
[ 1.098346] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.104098] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.112151] libphy: XEMACPS mii bus: probed
[ 1.116719] ------------- phy_id = 0x3625e62
[ 1.121440] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.130081] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.136733] ehci-pci: EHCI PCI platform driver
[ 1.143936] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.150768] usbcore: registered new interface driver usb-storage
[ 1.157628] mousedev: PS/2 mouse device common for all mice
[ 1.163709] i2c /dev entries driver
[ 1.170637] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.176162] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.182020] Xilinx Zynq CpuIdle Driver started
[ 1.186898] sdhci: Secure Digital Host Controller Interface driver
[ 1.192989] sdhci: Copyright(c) Pierre Ossman
[ 1.197355] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.204137] mmc0: no vqmmc regulator found
[ 1.208220] mmc0: no vmmc regulator found
[ 1.245947] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.254610] usbcore: registered new interface driver usbhid
[ 1.260122] usbhid: USB HID core driver
[ 1.264819] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.271114] nand: Micron MT29F2G08ABAEAWP
[ 1.275080] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.281029] Bad block table found at page 131008, version 0x01
[ 1.287256] Bad block table found at page 130944, version 0x01
[ 1.293304] 3 ofpart partitions found on MTD device pl353-nand
[ 1.299089] Creating 3 MTD partitions on "pl353-nand":
[ 1.304179] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.312206] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.319525] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.330227] TCP: cubic registered
[ 1.333461] NET: Registered protocol family 17
[ 1.338156] Registering SWP/SWPB emulation handler
[ 1.344071] regulator-dummy: disabling
[ 1.348399] UBI: attaching mtd1 to ubi0
[ 1.657320] UBI: scanning is finished
[ 1.677859] UBI: volume 0 ("rootfs") re-sized from 192 to 1108 LEBs
[ 1.684915] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.691995] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.698760] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.705424] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.712302] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.718283] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.725390] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1113221046
[ 1.734433] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.743649] UBI: background thread "ubi_bgt0d" started, PID 1084
[ 1.743654] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.747608] ALSA device list:
[ 1.747611] No soundcards found.
[ 1.766145] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[ 1.838291] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.844217] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.853364] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.863241] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.868277] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E8A4479F-B15D-4C7A-964D-0F246E2BB6ED, small LPT model
[ 1.888578] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.000873] devtmpfs: mounted
[ 2.003982] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[ 3.268115] random: dd urandom read with 1 bits of entropy available
[ 3.875945]
[ 3.875945] bcm54xx_config_init
[ 4.985968]
[ 4.985968] bcm54xx_config_init
[ 7.986813] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 7.992900] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 21.416469] In axi fpga driver!
[ 21.419541] request_mem_region OK!
[ 21.422937] AXI fpga dev virtual address is 0xf0200000
[ 21.428068] *base_vir_addr = 0xc51e
[ 21.442664] In fpga mem driver!
[ 21.446087] request_mem_region OK!
[ 21.449600] fpga mem virtual address is 0xf3000000
[ 22.215976]
[ 22.215976] bcm54xx_config_init
[ 23.295979]
[ 23.295979] bcm54xx_config_init
[ 26.296813] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 26.302830] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 1086.424488] random: nonblocking pool is initialized
main.c:13992: log_level = 4
main.c:14019: This is XILINX board. Totalram: 1039753216
main.c:14025: Detect 1GB control board of XILINX
driver-bitmain.c:1776: mmap axi_fpga_addr = 0xb6f55000
driver-bitmain.c:1781: axi_fpga_addr data = 0xc51e
driver-bitmain.c:1797: mmap fpga_mem_addr = 0xb5d4e000
driver-bitmain.c:994: forceFreq=-1 forceFlag=0
driver-bitmain.c:1696: min work minertest[0]:912
main.c:8570: DETECT HW version=0000c51e
main.c:14064: miner ID : 8128ed8162bb8854
main.c:14089: Miner Type = S9
main.c:14101: AsicType = 1387
main.c:14104: real AsicNum = 63
main.c:14197: use critical mode to search freq...
driver-bitmain.c:1876: get PLUG ON=0x000000e0
driver-bitmain.c:1946: Find hashboard on Chain[5]
driver-bitmain.c:1946: Find hashboard on Chain[6]
driver-bitmain.c:1946: Find hashboard on Chain[7]
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:2282: Check chain[6] PIC fw version=0x03
main.c:2282: Check chain[7] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[5]: [44:101] [38:104] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8974: Chain[5] disabled chip[38] core[104]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[5] has freq in PIC and will jump over...
main.c:9103: Chain[5] has core num in PIC
main.c:9113: Chain[5] ASIC[0] has core num=1
main.c:9113: Chain[5] ASIC[1] has core num=2
main.c:9113: Chain[5] ASIC[2] has core num=1
main.c:9113: Chain[5] ASIC[3] has core num=1
main.c:9113: Chain[5] ASIC[4] has core num=1
main.c:9113: Chain[5] ASIC[5] has core num=1
main.c:9113: Chain[5] ASIC[6] has core num=1
main.c:9113: Chain[5] ASIC[7] has core num=1
main.c:9113: Chain[5] ASIC[8] has core num=2
main.c:9113: Chain[5] ASIC[9] has core num=1
main.c:9113: Chain[5] ASIC[11] has core num=1
main.c:9113: Chain[5] ASIC[12] has core num=1
main.c:9113: Chain[5] ASIC[13] has core num=1
main.c:9113: Chain[5] ASIC[14] has core num=1
main.c:9113: Chain[5] ASIC[15] has core num=1
main.c:9113: Chain[5] ASIC[16] has core num=1
main.c:9113: Chain[5] ASIC[17] has core num=1
main.c:9113: Chain[5] ASIC[18] has core num=1
main.c:9113: Chain[5] ASIC[19] has core num=1
main.c:9113: Chain[5] ASIC[20] has core num=1
main.c:9113: Chain[5] ASIC[21] has core num=1
main.c:9113: Chain[5] ASIC[23] has core num=1
main.c:9113: Chain[5] ASIC[24] has core num=1
main.c:9113: Chain[5] ASIC[25] has core num=1
main.c:9113: Chain[5] ASIC[26] has core num=1
main.c:9113: Chain[5] ASIC[27] has core num=1
main.c:9113: Chain[5] ASIC[28] has core num=1
main.c:9113: Chain[5] ASIC[29] has core num=2
main.c:9113: Chain[5] ASIC[30] has core num=1
main.c:9113: Chain[5] ASIC[31] has core num=1
main.c:9113: Chain[5] ASIC[32] has core num=1
main.c:9113: Chain[5] ASIC[33] has core num=1
main.c:9113: Chain[5] ASIC[35] has core num=1
main.c:9113: Chain[5] ASIC[36] has core num=1
main.c:9113: Chain[5] ASIC[37] has core num=1
main.c:9113: Chain[5] ASIC[38] has core num=1
main.c:9113: Chain[5] ASIC[39] has core num=1
main.c:9113: Chain[5] ASIC[40] has core num=1
main.c:9113: Chain[5] ASIC[41] has core num=2
main.c:9113: Chain[5] ASIC[42] has core num=1
main.c:9113: Chain[5] ASIC[43] has core num=2
main.c:9113: Chain[5] ASIC[44] has core num=1
main.c:9113: Chain[5] ASIC[45] has core num=1
main.c:9113: Chain[5] ASIC[46] has core num=1
main.c:9113: Chain[5] ASIC[47] has core num=1
main.c:9113: Chain[5] ASIC[48] has core num=1
main.c:9113: Chain[5] ASIC[49] has core num=1
main.c:9113: Chain[5] ASIC[50] has core num=1
main.c:9113: Chain[5] ASIC[51] has core num=1
main.c:9113: Chain[5] ASIC[52] has core num=1
main.c:9113: Chain[5] ASIC[54] has core num=1
main.c:9113: Chain[5] ASIC[55] has core num=1
main.c:9113: Chain[5] ASIC[56] has core num=1
main.c:9113: Chain[5] ASIC[57] has core num=1
main.c:9113: Chain[5] ASIC[58] has core num=1
main.c:9113: Chain[5] ASIC[59] has core num=1
main.c:9113: Chain[5] ASIC[61] has core num=1
main.c:9113: Chain[5] ASIC[62] has core num=1
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[6] has freq in PIC and will jump over...
main.c:9103: Chain[6] has core num in PIC
main.c:9113: Chain[6] ASIC[0] has core num=1
main.c:9113: Chain[6] ASIC[1] has core num=2
main.c:9113: Chain[6] ASIC[2] has core num=1
main.c:9113: Chain[6] ASIC[5] has core num=2
main.c:9113: Chain[6] ASIC[8] has core num=1
main.c:9113: Chain[6] ASIC[9] has core num=1
main.c:9113: Chain[6] ASIC[11] has core num=1
main.c:9113: Chain[6] ASIC[12] has core num=1
main.c:9113: Chain[6] ASIC[13] has core num=1
main.c:9113: Chain[6] ASIC[16] has core num=1
main.c:9113: Chain[6] ASIC[17] has core num=1
main.c:9113: Chain[6] ASIC[19] has core num=1
main.c:9113: Chain[6] ASIC[21] has core num=1
main.c:9113: Chain[6] ASIC[22] has core num=2
main.c:9113: Chain[6] ASIC[23] has core num=1
main.c:9113: Chain[6] ASIC[24] has core num=1
main.c:9113: Chain[6] ASIC[25] has core num=15
main.c:9113: Chain[6] ASIC[26] has core num=1
main.c:9113: Chain[6] ASIC[27] has core num=1
main.c:9113: Chain[6] ASIC[29] has core num=2
main.c:9113: Chain[6] ASIC[30] has core num=2
main.c:9113: Chain[6] ASIC[31] has core num=1
main.c:9113: Chain[6] ASIC[32] has core num=1
main.c:9113: Chain[6] ASIC[34] has core num=1
main.c:9113: Chain[6] ASIC[35] has core num=1
main.c:9113: Chain[6] ASIC[36] has core num=1
main.c:9113: Chain[6] ASIC[37] has core num=1
main.c:9113: Chain[6] ASIC[38] has core num=3
main.c:9113: Chain[6] ASIC[40] has core num=1
main.c:9113: Chain[6] ASIC[41] has core num=1
main.c:9113: Chain[6] ASIC[42] has core num=3
main.c:9113: Chain[6] ASIC[43] has core num=2
main.c:9113: Chain[6] ASIC[45] has core num=1
main.c:9113: Chain[6] ASIC[46] has core num=1
main.c:9113: Chain[6] ASIC[47] has core num=1
main.c:9113: Chain[6] ASIC[50] has core num=1
main.c:9113: Chain[6] ASIC[51] has core num=2
main.c:9113: Chain[6] ASIC[52] has core num=1
main.c:9113: Chain[6] ASIC[53] has core num=1
main.c:9113: Chain[6] ASIC[54] has core num=1
main.c:9113: Chain[6] ASIC[55] has core num=1
main.c:9113: Chain[6] ASIC[56] has core num=1
main.c:9113: Chain[6] ASIC[58] has core num=15
main.c:9113: Chain[6] ASIC[59] has core num=1
main.c:9113: Chain[6] ASIC[60] has core num=2
main.c:9113: Chain[6] ASIC[61] has core num=1
main.c:9113: Chain[6] ASIC[62] has core num=1
main.c:2282: Check chain[6] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[7] has freq in PIC and will jump over...
main.c:9103: Chain[7] has core num in PIC
main.c:9113: Chain[7] ASIC[0] has core num=1
main.c:9113: Chain[7] ASIC[1] has core num=2
main.c:9113: Chain[7] ASIC[2] has core num=2
main.c:9113: Chain[7] ASIC[3] has core num=1
main.c:9113: Chain[7] ASIC[4] has core num=1
main.c:9113: Chain[7] ASIC[6] has core num=1
main.c:9113: Chain[7] ASIC[7] has core num=2
main.c:9113: Chain[7] ASIC[8] has core num=1
main.c:9113: Chain[7] ASIC[9] has core num=1
main.c:9113: Chain[7] ASIC[10] has core num=4
main.c:9113: Chain[7] ASIC[11] has core num=1
main.c:9113: Chain[7] ASIC[12] has core num=1
main.c:9113: Chain[7] ASIC[14] has core num=1
main.c:9113: Chain[7] ASIC[15] has core num=1
main.c:9113: Chain[7] ASIC[16] has core num=1
main.c:9113: Chain[7] ASIC[17] has core num=1
main.c:9113: Chain[7] ASIC[18] has core num=1
main.c:9113: Chain[7] ASIC[19] has core num=1
main.c:9113: Chain[7] ASIC[20] has core num=1
main.c:9113: Chain[7] ASIC[21] has core num=1
main.c:9113: Chain[7] ASIC[22] has core num=1
main.c:9113: Chain[7] ASIC[23] has core num=1
main.c:9113: Chain[7] ASIC[24] has core num=1
main.c:9113: Chain[7] ASIC[26] has core num=1
main.c:9113: Chain[7] ASIC[27] has core num=1
main.c:9113: Chain[7] ASIC[28] has core num=1
main.c:9113: Chain[7] ASIC[29] has core num=1
main.c:9113: Chain[7] ASIC[30] has core num=1
main.c:9113: Chain[7] ASIC[31] has core num=1
main.c:9113: Chain[7] ASIC[32] has core num=2
main.c:9113: Chain[7] ASIC[33] has core num=1
main.c:9113: Chain[7] ASIC[34] has core num=1
main.c:9113: Chain[7] ASIC[35] has core num=1
main.c:9113: Chain[7] ASIC[36] has core num=1
main.c:9113: Chain[7] ASIC[37] has core num=1
main.c:9113: Chain[7] ASIC[40] has core num=1
main.c:9113: Chain[7] ASIC[41] has core num=1
main.c:9113: Chain[7] ASIC[42] has core num=1
main.c:9113: Chain[7] ASIC[43] has core num=1
main.c:9113: Chain[7] ASIC[44] has core num=1
main.c:9113: Chain[7] ASIC[45] has core num=1
main.c:9113: Chain[7] ASIC[46] has core num=1
main.c:9113: Chain[7] ASIC[47] has core num=1
main.c:9113: Chain[7] ASIC[48] has core num=1
main.c:9113: Chain[7] ASIC[49] has core num=1
main.c:9113: Chain[7] ASIC[50] has core num=1
main.c:9113: Chain[7] ASIC[51] has core num=1
main.c:9113: Chain[7] ASIC[52] has core num=1
main.c:9113: Chain[7] ASIC[53] has core num=1
main.c:9113: Chain[7] ASIC[54] has core num=1
main.c:9113: Chain[7] ASIC[55] has core num=1
main.c:9113: Chain[7] ASIC[56] has core num=1
main.c:9113: Chain[7] ASIC[57] has core num=1
main.c:9113: Chain[7] ASIC[58] has core num=1
main.c:9113: Chain[7] ASIC[60] has core num=1
main.c:9113: Chain[7] ASIC[61] has core num=1
main.c:9113: Chain[7] ASIC[62] has core num=1
main.c:2282: Check chain[7] PIC fw version=0x03
main.c:9183: get PIC voltage=6 on chain[5], value=940
main.c:9183: get PIC voltage=6 on chain[6], value=940
main.c:9183: get PIC voltage=6 on chain[7], value=940
main.c:9349: chain[5] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[5] temp chip I2C addr=0x98
main.c:9372: chain[5] has no middle temp, use special fix mode.
main.c:9349: chain[6] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[6] temp chip I2C addr=0x98
main.c:9372: chain[6] has no middle temp, use special fix mode.
main.c:9349: chain[7] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[7] temp chip I2C addr=0x98
main.c:9372: chain[7] has no middle temp, use special fix mode.
main.c:13956: total_exist_chain_num = 3
main.c:9562: CRC error counter=0
main.c:9577: set command mode to VIL
main.c:9649:
--- check asic number
main.c:9745: After Get ASIC NUM CRC error counter=0
main.c:9768: set_baud=0
main.c:10693: The min freq=700
main.c:10695: set real timeout 52, need sleep=379392
main.c:12825: After TEST CRC error counter=0
main.c:14236: search freq for 1 times, completed chain = 3, total chain num = 3
board_frq_tuning.c:628: single_board_frq_tuning enter
board_frq_tuning.c:629: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:254: force_freq not set, don't need tuning
main.c:14645: restart Miner chance num=2
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13927: bmminer not found=17661 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
main.c:13927: bmminer not found=12195 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
driver-btm-c5.c:12243:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12286:bitmain_c5_init: Detect 1GB control board of XILINX
driver-btm-c5.c:12313:bitmain_c5_init: Miner Type = S9
driver-btm-c5.c:12324:bitmain_c5_init: Miner compile time: Wed Jul 31 16:18:27 CST 2019 type: Antminer S9
driver-btm-c5.c:12414:bitmain_c5_init: miner ID : 8128ed8162bb8854
driver-btm-c5.c:12571:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=4320
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=4320
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=5280
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=4320
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=5280
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=4320
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=5280
driver-btm-c5.c:13108:bitmain_c5_init: chain[5]: [44:101] [38:104] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x49 0x00 0x49 0x04 0x49 0x09 0x49 0x00 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x05 0x49 0x09 0x49 0x23 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=3 : 0
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J6] has backup chain_voltage=890
driver-btm-c5.c:13193:bitmain_c5_init: scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[5] PIC fw version=0x03
driver-btm-c5.c:13108:bitmain_c5_init: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x4f 0x00 0x4f 0x05 0x4f 0x00 0x4f 0x00 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x05 0x4f 0x07 0x4f 0x23 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=3 : 0
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J7] has backup chain_voltage=870
driver-btm-c5.c:13193:bitmain_c5_init: scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[6] PIC fw version=0x03
driver-btm-c5.c:13108:bitmain_c5_init: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x49 0x00 0x49 0x04 0x49 0x09 0x49 0x00 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x05 0x49 0x09 0x49 0x23 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=3 : 0
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J8] has backup chain_voltage=890
driver-btm-c5.c:13193:bitmain_c5_init: scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[7] PIC fw version=0x03
driver-btm-c5.c:12195:init_exist_chain_table: total_exist_chain_num = 3
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J6] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J6] will use backup chain_voltage_pic=890 [91]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J6] get working chain_voltage_pic=91
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J7] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J7] will use backup chain_voltage_pic=870 [125]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J7] get working chain_voltage_pic=125
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J8] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J8] will use backup chain_voltage_pic=890 [91]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J8] get working chain_voltage_pic=91
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:4571:set_frequency: miner total rate=0GH/s ideal_total_hash_rate = 0GH/s
driver-btm-c5.c:4819:set_frequency: Miner fix freq ...
driver-btm-c5.c:5119:set_frequency: max freq = 100
driver-btm-c5.c:4162:ProcessFixFreq: totalRate = 0, fixed_totalRate = 0
driver-btm-c5.c:9604:init_uart_baud: set baud=1
driver-btm-c5.c:12103:set_working_voltage: setting to working voltage...
driver-btm-c5.c:13954:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=1695 total_tv_end_sys=1696
driver-btm-c5.c:8727:read_temp_func: bring_up_pcb_temp = -100
driver-btm-c5.c:10320:check_system_work: restartNum = 2 , auto-reinit enabled...
driver-btm-c5.c:9887:if_avg_hash_ok: avg hash rate = 0.000000, ideal hash rate = 0
driver-btm-c5.c:10387:check_system_work: hash rate is low...
driver-btm-c5.c:15630:re_open_core: re_open_core enter
driver-btm-c5.c:15791:re_open_core: Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 0, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 1, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 2, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 3, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 4, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 5, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 6, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 7, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 8, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 9, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 10, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 11, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 12, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 13, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 14, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 15, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 16, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 17, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 18, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 19, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15791:re_open_core: Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 0, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 1, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 2, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 3, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 4, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 5, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 6, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 7, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 8, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 9, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 10, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 11, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 12, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 13, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 14, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 15, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 16, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 17, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 18, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 19, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15791:re_open_core: Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 0, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 1, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 2, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 3, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 4, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 5, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 6, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 7, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 8, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 9, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 10, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 11, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 12, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 13, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 14, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 15, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 16, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 17, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 18, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 19, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:4571:set_frequency: miner total rate=0GH/s ideal_total_hash_rate = 0GH/s
driver-btm-c5.c:4819:set_frequency: Miner fix freq ...
driver-btm-c5.c:5119:set_frequency: max freq = 100
driver-btm-c5.c:4162:ProcessFixFreq: totalRate = 0, fixed_totalRate = 0
driver-btm-c5.c:9604:init_uart_baud: set baud=1
driver-btm-c5.c:16082:re_open_core: reopen core end
driver-btm-c5.c:10400:check_system_work: re-open core 1 times
driver-btm-c5.c:10427:check_system_work: checking hash again
driver-btm-c5.c:9887:if_avg_hash_ok: avg hash rate = 0.000000, ideal hash rate = 0
driver-btm-c5.c:9887:if_avg_hash_ok: avg hash rate = 0.000000, ideal hash rate = 0
driver-btm-c5.c:10387:check_system_work: hash rate is low...
driver-btm-c5.c:15630:re_open_core: re_open_core enter
driver-btm-c5.c:15791:re_open_core: Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 0, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 1, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 2, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 3, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 4, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 5, dev->chain_asic_num[i] = 0
do read_temp_func once...
Done check_asic_reg
Max pcb temp : -100
set FAN speed according to: temp_highest=-100 temp_top1[PWM_T]=-100 temp_top1[TEMP_POS_LOCAL]=-100 temp_change=0 fix_fan_steps=0
FAN PWM: 0
read_temp_func Done!
CRC error counter=9
[ 0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 27800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map e6fd8000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 496 pages used for memmap
[ 0.000000] HighMem zone: 63488 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256528
[ 0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 884108K/1032192K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 148084K reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06da8ac (6987 kB)
[ 0.000000] .init : 0xc06db000 - 0xc070e380 ( 205 kB)
[ 0.000000] .data : 0xc0710000 - 0xc0757138 ( 285 kB)
[ 0.000000] .bss : 0xc0757144 - 0xc0797bfc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to f0004000
[ 0.000000] zynq_clock_init: clkc starts at f0004100
[ 0.000000] Zynq clock init
[ 0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000293] ps7-ttc #0 at f0006000, irq=43
[ 0.000594] Console: colour dummy device 80x30
[ 0.000630] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[ 0.090243] pid_max: default: 32768 minimum: 301
[ 0.090453] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.090475] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.092629] CPU: Testing write buffer coherency: ok
[ 0.092952] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.093009] Setting up static identity map for 0x4cb118 - 0x4cb170
[ 0.093229] L310 cache controller enabled
[ 0.093250] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.170988] CPU1: Booted secondary processor
[ 0.260220] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.260348] Brought up 2 CPUs
[ 0.260368] SMP: Total of 2 processors activated.
[ 0.260376] CPU: All CPU(s) started in SVC mode.
[ 0.261051] devtmpfs: initialized
[ 0.263464] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.264652] regulator-dummy: no parameters
[ 0.271509] NET: Registered protocol family 16
[ 0.273784] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.276038] cpuidle: using governor ladder
[ 0.276051] cpuidle: using governor menu
[ 0.283416] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.284920] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.284934] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.285043] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[ 0.306625] bio: create slab
[ 0.308018] vgaarb: loaded
[ 0.308737] SCSI subsystem initialized
[ 0.309607] usbcore: registered new interface driver usbfs
[ 0.309793] usbcore: registered new interface driver hub
[ 0.310018] usbcore: registered new device driver usb
[ 0.310682] media: Linux media interface: v0.10
[ 0.310838] Linux video capture interface: v2.00
[ 0.311442] pps_core: LinuxPPS API ver. 1 registered
[ 0.311454] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.311588] PTP clock support registered
[ 0.311933] EDAC MC: Ver: 3.0.0
[ 0.313121] Advanced Linux Sound Architecture Driver Initialized.
[ 0.315846] DMA-API: preallocated 4096 debug entries
[ 0.315858] DMA-API: debugging enabled by kernel config
[ 0.315928] Switched to clocksource arm_global_timer
[ 0.336124] NET: Registered protocol family 2
[ 0.336778] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.336872] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.337031] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.337095] TCP: reno registered
[ 0.337111] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.337160] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.337412] NET: Registered protocol family 1
[ 0.337746] RPC: Registered named UNIX socket transport module.
[ 0.337758] RPC: Registered udp transport module.
[ 0.337767] RPC: Registered tcp transport module.
[ 0.337775] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.337786] PCI: CLS 0 bytes, default 64
[ 0.338210] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.340200] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.341568] bounce pool size: 64 pages
[ 0.342437] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.342641] msgmni has been set to 1486
[ 0.343395] io scheduler noop registered
[ 0.343409] io scheduler deadline registered
[ 0.343449] io scheduler cfq registered (default)
[ 0.355673] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.355693] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.478687] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.050741] console [ttyPS0] enabled
[ 1.054981] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[ 1.062587] [drm] Initialized drm 1.1.0 20060810
[ 1.079562] brd: module loaded
[ 1.088950] loop: module loaded
[ 1.098346] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.104098] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.112151] libphy: XEMACPS mii bus: probed
[ 1.116719] ------------- phy_id = 0x3625e62
[ 1.121440] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.130081] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.136733] ehci-pci: EHCI PCI platform driver
[ 1.143936] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.150768] usbcore: registered new interface driver usb-storage
[ 1.157628] mousedev: PS/2 mouse device common for all mice
[ 1.163709] i2c /dev entries driver
[ 1.170637] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.176162] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.182020] Xilinx Zynq CpuIdle Driver started
[ 1.186898] sdhci: Secure Digital Host Controller Interface driver
[ 1.192989] sdhci: Copyright(c) Pierre Ossman
[ 1.197355] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.204137] mmc0: no vqmmc regulator found
[ 1.208220] mmc0: no vmmc regulator found
[ 1.245947] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.254610] usbcore: registered new interface driver usbhid
[ 1.260122] usbhid: USB HID core driver
[ 1.264819] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.271114] nand: Micron MT29F2G08ABAEAWP
[ 1.275080] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.281029] Bad block table found at page 131008, version 0x01
[ 1.287256] Bad block table found at page 130944, version 0x01
[ 1.293304] 3 ofpart partitions found on MTD device pl353-nand
[ 1.299089] Creating 3 MTD partitions on "pl353-nand":
[ 1.304179] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.312206] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.319525] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.330227] TCP: cubic registered
[ 1.333461] NET: Registered protocol family 17
[ 1.338156] Registering SWP/SWPB emulation handler
[ 1.344071] regulator-dummy: disabling
[ 1.348399] UBI: attaching mtd1 to ubi0
[ 1.657320] UBI: scanning is finished
[ 1.677859] UBI: volume 0 ("rootfs") re-sized from 192 to 1108 LEBs
[ 1.684915] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.691995] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.698760] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.705424] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.712302] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.718283] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.725390] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1113221046
[ 1.734433] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.743649] UBI: background thread "ubi_bgt0d" started, PID 1084
[ 1.743654] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.747608] ALSA device list:
[ 1.747611] No soundcards found.
[ 1.766145] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[ 1.838291] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.844217] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.853364] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.863241] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.868277] UBIFS: media format: w4/r0 (latest is w4/r0), UUID E8A4479F-B15D-4C7A-964D-0F246E2BB6ED, small LPT model
[ 1.888578] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 2.000873] devtmpfs: mounted
[ 2.003982] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[ 3.268115] random: dd urandom read with 1 bits of entropy available
[ 3.875945]
[ 3.875945] bcm54xx_config_init
[ 4.985968]
[ 4.985968] bcm54xx_config_init
[ 7.986813] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 7.992900] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 21.416469] In axi fpga driver!
[ 21.419541] request_mem_region OK!
[ 21.422937] AXI fpga dev virtual address is 0xf0200000
[ 21.428068] *base_vir_addr = 0xc51e
[ 21.442664] In fpga mem driver!
[ 21.446087] request_mem_region OK!
[ 21.449600] fpga mem virtual address is 0xf3000000
[ 22.215976]
[ 22.215976] bcm54xx_config_init
[ 23.295979]
[ 23.295979] bcm54xx_config_init
[ 26.296813] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 26.302830] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 1086.424488] random: nonblocking pool is initialized
main.c:13992: log_level = 4
main.c:14019: This is XILINX board. Totalram: 1039753216
main.c:14025: Detect 1GB control board of XILINX
driver-bitmain.c:1776: mmap axi_fpga_addr = 0xb6f55000
driver-bitmain.c:1781: axi_fpga_addr data = 0xc51e
driver-bitmain.c:1797: mmap fpga_mem_addr = 0xb5d4e000
driver-bitmain.c:994: forceFreq=-1 forceFlag=0
driver-bitmain.c:1696: min work minertest[0]:912
main.c:8570: DETECT HW version=0000c51e
main.c:14064: miner ID : 8128ed8162bb8854
main.c:14089: Miner Type = S9
main.c:14101: AsicType = 1387
main.c:14104: real AsicNum = 63
main.c:14197: use critical mode to search freq...
driver-bitmain.c:1876: get PLUG ON=0x000000e0
driver-bitmain.c:1946: Find hashboard on Chain[5]
driver-bitmain.c:1946: Find hashboard on Chain[6]
driver-bitmain.c:1946: Find hashboard on Chain[7]
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:2282: Check chain[6] PIC fw version=0x03
main.c:2282: Check chain[7] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[5]: [44:101] [38:104] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8974: Chain[5] disabled chip[38] core[104]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[5] has freq in PIC and will jump over...
main.c:9103: Chain[5] has core num in PIC
main.c:9113: Chain[5] ASIC[0] has core num=1
main.c:9113: Chain[5] ASIC[1] has core num=2
main.c:9113: Chain[5] ASIC[2] has core num=1
main.c:9113: Chain[5] ASIC[3] has core num=1
main.c:9113: Chain[5] ASIC[4] has core num=1
main.c:9113: Chain[5] ASIC[5] has core num=1
main.c:9113: Chain[5] ASIC[6] has core num=1
main.c:9113: Chain[5] ASIC[7] has core num=1
main.c:9113: Chain[5] ASIC[8] has core num=2
main.c:9113: Chain[5] ASIC[9] has core num=1
main.c:9113: Chain[5] ASIC[11] has core num=1
main.c:9113: Chain[5] ASIC[12] has core num=1
main.c:9113: Chain[5] ASIC[13] has core num=1
main.c:9113: Chain[5] ASIC[14] has core num=1
main.c:9113: Chain[5] ASIC[15] has core num=1
main.c:9113: Chain[5] ASIC[16] has core num=1
main.c:9113: Chain[5] ASIC[17] has core num=1
main.c:9113: Chain[5] ASIC[18] has core num=1
main.c:9113: Chain[5] ASIC[19] has core num=1
main.c:9113: Chain[5] ASIC[20] has core num=1
main.c:9113: Chain[5] ASIC[21] has core num=1
main.c:9113: Chain[5] ASIC[23] has core num=1
main.c:9113: Chain[5] ASIC[24] has core num=1
main.c:9113: Chain[5] ASIC[25] has core num=1
main.c:9113: Chain[5] ASIC[26] has core num=1
main.c:9113: Chain[5] ASIC[27] has core num=1
main.c:9113: Chain[5] ASIC[28] has core num=1
main.c:9113: Chain[5] ASIC[29] has core num=2
main.c:9113: Chain[5] ASIC[30] has core num=1
main.c:9113: Chain[5] ASIC[31] has core num=1
main.c:9113: Chain[5] ASIC[32] has core num=1
main.c:9113: Chain[5] ASIC[33] has core num=1
main.c:9113: Chain[5] ASIC[35] has core num=1
main.c:9113: Chain[5] ASIC[36] has core num=1
main.c:9113: Chain[5] ASIC[37] has core num=1
main.c:9113: Chain[5] ASIC[38] has core num=1
main.c:9113: Chain[5] ASIC[39] has core num=1
main.c:9113: Chain[5] ASIC[40] has core num=1
main.c:9113: Chain[5] ASIC[41] has core num=2
main.c:9113: Chain[5] ASIC[42] has core num=1
main.c:9113: Chain[5] ASIC[43] has core num=2
main.c:9113: Chain[5] ASIC[44] has core num=1
main.c:9113: Chain[5] ASIC[45] has core num=1
main.c:9113: Chain[5] ASIC[46] has core num=1
main.c:9113: Chain[5] ASIC[47] has core num=1
main.c:9113: Chain[5] ASIC[48] has core num=1
main.c:9113: Chain[5] ASIC[49] has core num=1
main.c:9113: Chain[5] ASIC[50] has core num=1
main.c:9113: Chain[5] ASIC[51] has core num=1
main.c:9113: Chain[5] ASIC[52] has core num=1
main.c:9113: Chain[5] ASIC[54] has core num=1
main.c:9113: Chain[5] ASIC[55] has core num=1
main.c:9113: Chain[5] ASIC[56] has core num=1
main.c:9113: Chain[5] ASIC[57] has core num=1
main.c:9113: Chain[5] ASIC[58] has core num=1
main.c:9113: Chain[5] ASIC[59] has core num=1
main.c:9113: Chain[5] ASIC[61] has core num=1
main.c:9113: Chain[5] ASIC[62] has core num=1
main.c:2282: Check chain[5] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[6] has freq in PIC and will jump over...
main.c:9103: Chain[6] has core num in PIC
main.c:9113: Chain[6] ASIC[0] has core num=1
main.c:9113: Chain[6] ASIC[1] has core num=2
main.c:9113: Chain[6] ASIC[2] has core num=1
main.c:9113: Chain[6] ASIC[5] has core num=2
main.c:9113: Chain[6] ASIC[8] has core num=1
main.c:9113: Chain[6] ASIC[9] has core num=1
main.c:9113: Chain[6] ASIC[11] has core num=1
main.c:9113: Chain[6] ASIC[12] has core num=1
main.c:9113: Chain[6] ASIC[13] has core num=1
main.c:9113: Chain[6] ASIC[16] has core num=1
main.c:9113: Chain[6] ASIC[17] has core num=1
main.c:9113: Chain[6] ASIC[19] has core num=1
main.c:9113: Chain[6] ASIC[21] has core num=1
main.c:9113: Chain[6] ASIC[22] has core num=2
main.c:9113: Chain[6] ASIC[23] has core num=1
main.c:9113: Chain[6] ASIC[24] has core num=1
main.c:9113: Chain[6] ASIC[25] has core num=15
main.c:9113: Chain[6] ASIC[26] has core num=1
main.c:9113: Chain[6] ASIC[27] has core num=1
main.c:9113: Chain[6] ASIC[29] has core num=2
main.c:9113: Chain[6] ASIC[30] has core num=2
main.c:9113: Chain[6] ASIC[31] has core num=1
main.c:9113: Chain[6] ASIC[32] has core num=1
main.c:9113: Chain[6] ASIC[34] has core num=1
main.c:9113: Chain[6] ASIC[35] has core num=1
main.c:9113: Chain[6] ASIC[36] has core num=1
main.c:9113: Chain[6] ASIC[37] has core num=1
main.c:9113: Chain[6] ASIC[38] has core num=3
main.c:9113: Chain[6] ASIC[40] has core num=1
main.c:9113: Chain[6] ASIC[41] has core num=1
main.c:9113: Chain[6] ASIC[42] has core num=3
main.c:9113: Chain[6] ASIC[43] has core num=2
main.c:9113: Chain[6] ASIC[45] has core num=1
main.c:9113: Chain[6] ASIC[46] has core num=1
main.c:9113: Chain[6] ASIC[47] has core num=1
main.c:9113: Chain[6] ASIC[50] has core num=1
main.c:9113: Chain[6] ASIC[51] has core num=2
main.c:9113: Chain[6] ASIC[52] has core num=1
main.c:9113: Chain[6] ASIC[53] has core num=1
main.c:9113: Chain[6] ASIC[54] has core num=1
main.c:9113: Chain[6] ASIC[55] has core num=1
main.c:9113: Chain[6] ASIC[56] has core num=1
main.c:9113: Chain[6] ASIC[58] has core num=15
main.c:9113: Chain[6] ASIC[59] has core num=1
main.c:9113: Chain[6] ASIC[60] has core num=2
main.c:9113: Chain[6] ASIC[61] has core num=1
main.c:9113: Chain[6] ASIC[62] has core num=1
main.c:2282: Check chain[6] PIC fw version=0x03
main.c:8940: read pic freq and badcore num...
main.c:8961: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:9003: has freq in PIC, will disable freq setting.
main.c:9099: chain[7] has freq in PIC and will jump over...
main.c:9103: Chain[7] has core num in PIC
main.c:9113: Chain[7] ASIC[0] has core num=1
main.c:9113: Chain[7] ASIC[1] has core num=2
main.c:9113: Chain[7] ASIC[2] has core num=2
main.c:9113: Chain[7] ASIC[3] has core num=1
main.c:9113: Chain[7] ASIC[4] has core num=1
main.c:9113: Chain[7] ASIC[6] has core num=1
main.c:9113: Chain[7] ASIC[7] has core num=2
main.c:9113: Chain[7] ASIC[8] has core num=1
main.c:9113: Chain[7] ASIC[9] has core num=1
main.c:9113: Chain[7] ASIC[10] has core num=4
main.c:9113: Chain[7] ASIC[11] has core num=1
main.c:9113: Chain[7] ASIC[12] has core num=1
main.c:9113: Chain[7] ASIC[14] has core num=1
main.c:9113: Chain[7] ASIC[15] has core num=1
main.c:9113: Chain[7] ASIC[16] has core num=1
main.c:9113: Chain[7] ASIC[17] has core num=1
main.c:9113: Chain[7] ASIC[18] has core num=1
main.c:9113: Chain[7] ASIC[19] has core num=1
main.c:9113: Chain[7] ASIC[20] has core num=1
main.c:9113: Chain[7] ASIC[21] has core num=1
main.c:9113: Chain[7] ASIC[22] has core num=1
main.c:9113: Chain[7] ASIC[23] has core num=1
main.c:9113: Chain[7] ASIC[24] has core num=1
main.c:9113: Chain[7] ASIC[26] has core num=1
main.c:9113: Chain[7] ASIC[27] has core num=1
main.c:9113: Chain[7] ASIC[28] has core num=1
main.c:9113: Chain[7] ASIC[29] has core num=1
main.c:9113: Chain[7] ASIC[30] has core num=1
main.c:9113: Chain[7] ASIC[31] has core num=1
main.c:9113: Chain[7] ASIC[32] has core num=2
main.c:9113: Chain[7] ASIC[33] has core num=1
main.c:9113: Chain[7] ASIC[34] has core num=1
main.c:9113: Chain[7] ASIC[35] has core num=1
main.c:9113: Chain[7] ASIC[36] has core num=1
main.c:9113: Chain[7] ASIC[37] has core num=1
main.c:9113: Chain[7] ASIC[40] has core num=1
main.c:9113: Chain[7] ASIC[41] has core num=1
main.c:9113: Chain[7] ASIC[42] has core num=1
main.c:9113: Chain[7] ASIC[43] has core num=1
main.c:9113: Chain[7] ASIC[44] has core num=1
main.c:9113: Chain[7] ASIC[45] has core num=1
main.c:9113: Chain[7] ASIC[46] has core num=1
main.c:9113: Chain[7] ASIC[47] has core num=1
main.c:9113: Chain[7] ASIC[48] has core num=1
main.c:9113: Chain[7] ASIC[49] has core num=1
main.c:9113: Chain[7] ASIC[50] has core num=1
main.c:9113: Chain[7] ASIC[51] has core num=1
main.c:9113: Chain[7] ASIC[52] has core num=1
main.c:9113: Chain[7] ASIC[53] has core num=1
main.c:9113: Chain[7] ASIC[54] has core num=1
main.c:9113: Chain[7] ASIC[55] has core num=1
main.c:9113: Chain[7] ASIC[56] has core num=1
main.c:9113: Chain[7] ASIC[57] has core num=1
main.c:9113: Chain[7] ASIC[58] has core num=1
main.c:9113: Chain[7] ASIC[60] has core num=1
main.c:9113: Chain[7] ASIC[61] has core num=1
main.c:9113: Chain[7] ASIC[62] has core num=1
main.c:2282: Check chain[7] PIC fw version=0x03
main.c:9183: get PIC voltage=6 on chain[5], value=940
main.c:9183: get PIC voltage=6 on chain[6], value=940
main.c:9183: get PIC voltage=6 on chain[7], value=940
main.c:9349: chain[5] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[5] temp chip I2C addr=0x98
main.c:9372: chain[5] has no middle temp, use special fix mode.
main.c:9349: chain[6] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[6] temp chip I2C addr=0x98
main.c:9372: chain[6] has no middle temp, use special fix mode.
main.c:9349: chain[7] temp offset record: 62,0,0,0,0,0,35,28
main.c:9366: chain[7] temp chip I2C addr=0x98
main.c:9372: chain[7] has no middle temp, use special fix mode.
main.c:13956: total_exist_chain_num = 3
main.c:9562: CRC error counter=0
main.c:9577: set command mode to VIL
main.c:9649:
--- check asic number
main.c:9745: After Get ASIC NUM CRC error counter=0
main.c:9768: set_baud=0
main.c:10693: The min freq=700
main.c:10695: set real timeout 52, need sleep=379392
main.c:12825: After TEST CRC error counter=0
main.c:14236: search freq for 1 times, completed chain = 3, total chain num = 3
board_frq_tuning.c:628: single_board_frq_tuning enter
board_frq_tuning.c:629: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:254: force_freq not set, don't need tuning
main.c:14645: restart Miner chance num=2
main.c:14685: waiting for receive_func to exit!
main.c:14699: waiting for pic heart to exit!
main.c:13927: bmminer not found=17661 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
main.c:13927: bmminer not found=12195 root 0:00 grep bmminer
main.c:14758: bmminer not found, restart bmminer ...
driver-btm-c5.c:12243:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12286:bitmain_c5_init: Detect 1GB control board of XILINX
driver-btm-c5.c:12313:bitmain_c5_init: Miner Type = S9
driver-btm-c5.c:12324:bitmain_c5_init: Miner compile time: Wed Jul 31 16:18:27 CST 2019 type: Antminer S9
driver-btm-c5.c:12414:bitmain_c5_init: miner ID : 8128ed8162bb8854
driver-btm-c5.c:12571:bitmain_c5_init: Checking fans...
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=4320
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=4320
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=5280
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=4320
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=5280
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[4] speed=4320
driver-btm-c5.c:3006:check_fan_beforeInit: get fan[5] speed=5280
driver-btm-c5.c:13108:bitmain_c5_init: chain[5]: [44:101] [38:104] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x49 0x00 0x49 0x04 0x49 0x09 0x49 0x00 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x05 0x49 0x09 0x49 0x23 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=3 : 0
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J6] has backup chain_voltage=890
driver-btm-c5.c:13193:bitmain_c5_init: scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[5] PIC fw version=0x03
driver-btm-c5.c:13108:bitmain_c5_init: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x4f 0x00 0x4f 0x05 0x4f 0x00 0x4f 0x00 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x05 0x4f 0x07 0x4f 0x23 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=3 : 0
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J7] has backup chain_voltage=870
driver-btm-c5.c:13193:bitmain_c5_init: scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[6] PIC fw version=0x03
driver-btm-c5.c:13108:bitmain_c5_init: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:13122:bitmain_c5_init: last_freq: 0x00 0x7d 0x00 0x49 0x00 0x49 0x04 0x49 0x09 0x49 0x00 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x03 0x49 0x05 0x49 0x09 0x49 0x23 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49 0x00 0x49
driver-btm-c5.c:13149:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:13155:bitmain_c5_init: Detect: S9_63 use voltage level=3 : 0
driver-btm-c5.c:13171:bitmain_c5_init: Chain[J8] has backup chain_voltage=890
driver-btm-c5.c:13193:bitmain_c5_init: scan based on domain
driver-btm-c5.c:1899:jump_to_app_CheckAndRestorePIC: Check chain[7] PIC fw version=0x03
driver-btm-c5.c:12195:init_exist_chain_table: total_exist_chain_num = 3
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J6] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J6] will use backup chain_voltage_pic=890 [91]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J6] get working chain_voltage_pic=91
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J7] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J7] will use backup chain_voltage_pic=870 [125]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J7] get working chain_voltage_pic=125
driver-btm-c5.c:13303:bitmain_c5_init: Chain[J8] orignal chain_voltage_pic=6 value=940
driver-btm-c5.c:13320:bitmain_c5_init: Chain[J8] will use backup chain_voltage_pic=890 [91]
driver-btm-c5.c:13330:bitmain_c5_init: Chain[J8] get working chain_voltage_pic=91
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J6] has 0 asic
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J7] has 0 asic
driver-btm-c5.c:13421:bitmain_c5_init: Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:13449:bitmain_c5_init: retry Chain[J8] has 0 asic
driver-btm-c5.c:4571:set_frequency: miner total rate=0GH/s ideal_total_hash_rate = 0GH/s
driver-btm-c5.c:4819:set_frequency: Miner fix freq ...
driver-btm-c5.c:5119:set_frequency: max freq = 100
driver-btm-c5.c:4162:ProcessFixFreq: totalRate = 0, fixed_totalRate = 0
driver-btm-c5.c:9604:init_uart_baud: set baud=1
driver-btm-c5.c:12103:set_working_voltage: setting to working voltage...
driver-btm-c5.c:13954:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=1695 total_tv_end_sys=1696
driver-btm-c5.c:8727:read_temp_func: bring_up_pcb_temp = -100
driver-btm-c5.c:10320:check_system_work: restartNum = 2 , auto-reinit enabled...
driver-btm-c5.c:9887:if_avg_hash_ok: avg hash rate = 0.000000, ideal hash rate = 0
driver-btm-c5.c:10387:check_system_work: hash rate is low...
driver-btm-c5.c:15630:re_open_core: re_open_core enter
driver-btm-c5.c:15791:re_open_core: Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 0, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 1, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 2, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 3, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 4, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 5, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 6, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 7, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 8, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 9, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 10, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 11, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 12, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 13, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 14, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 15, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 16, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 17, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 18, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 19, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15791:re_open_core: Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 0, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 1, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 2, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 3, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 4, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 5, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 6, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 7, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 8, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 9, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 10, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 11, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 12, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 13, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 14, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 15, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 16, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 17, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 18, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 6, retry_count = 19, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J7] has 0 asic
driver-btm-c5.c:15791:re_open_core: Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 0, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 1, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 2, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 3, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 4, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 5, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 6, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 7, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 8, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 9, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 10, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 11, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 12, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 13, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 14, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 15, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 16, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 17, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 18, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 7, retry_count = 19, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J8] has 0 asic
driver-btm-c5.c:4571:set_frequency: miner total rate=0GH/s ideal_total_hash_rate = 0GH/s
driver-btm-c5.c:4819:set_frequency: Miner fix freq ...
driver-btm-c5.c:5119:set_frequency: max freq = 100
driver-btm-c5.c:4162:ProcessFixFreq: totalRate = 0, fixed_totalRate = 0
driver-btm-c5.c:9604:init_uart_baud: set baud=1
driver-btm-c5.c:16082:re_open_core: reopen core end
driver-btm-c5.c:10400:check_system_work: re-open core 1 times
driver-btm-c5.c:10427:check_system_work: checking hash again
driver-btm-c5.c:9887:if_avg_hash_ok: avg hash rate = 0.000000, ideal hash rate = 0
driver-btm-c5.c:9887:if_avg_hash_ok: avg hash rate = 0.000000, ideal hash rate = 0
driver-btm-c5.c:10387:check_system_work: hash rate is low...
driver-btm-c5.c:15630:re_open_core: re_open_core enter
driver-btm-c5.c:15791:re_open_core: Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 0, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 1, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 2, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 3, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 4, dev->chain_asic_num[i] = 0
driver-btm-c5.c:15818:re_open_core: retry Chain[J6] has 0 asic
driver-btm-c5.c:15795:re_open_core: i = 5, retry_count = 5, dev->chain_asic_num[i] = 0
do read_temp_func once...
Done check_asic_reg
Max pcb temp : -100
set FAN speed according to: temp_highest=-100 temp_top1[PWM_T]=-100 temp_top1[TEMP_POS_LOCAL]=-100 temp_change=0 fix_fan_steps=0
FAN PWM: 0
read_temp_func Done!
CRC error counter=9
Jump to: