normally fan 1 is up front where the controllers ethernet jack is and fan 3 is on the back side
Topic: antminer S9 one of the fan started running slow (Read 1148 times)
Try to oil the fan if that didn't work you should replace it.
u know if "fan 3" is back or front fan?
Try to oil the fan if that didn't work you should replace it.
Have you plugged them in the right way around? Im guessing when you cleaned them you have plugged the fans back in different connectors on the controlboard
yeah they are connected in the right place. im still getting 1440/1800 rpm on "fan 3" thats front fan right?
Have you plugged them in the right way around? Im guessing when you cleaned them you have plugged the fans back in different connectors on the controlboard
You sould periodically clean your miners as dust builds up and coats the heatsinks and fns as youve found out. Switch it off and clean everything and see how you get on.
i did it.. but one of the fan is still slow.. its stuck on 1800rpm and wont increaseso buy a replacement fan
this one is okay
https://bitmainwarranty.com/shop/products/us/fan_s7/
this is good
https://www.amazon.com/Sanyo-Denki-SAN-Ace-120mm/dp/B00QWB1X3O/ref=sr_1_1?
I had a case of these,but all gone
https://www.amazon.com/Sanyo-Denki-SAN-Ace-120mm/dp/B00YOC80IO/ref=sr_1_2?
but its weird that front fan was running slow now is the back one that is running slow and the front one is now running at normal speed..
You sould periodically clean your miners as dust builds up and coats the heatsinks and fns as youve found out. Switch it off and clean everything and see how you get on.
i did it.. but one of the fan is still slow.. its stuck on 1800rpm and wont increaseso buy a replacement fan
this one is okay
https://bitmainwarranty.com/shop/products/us/fan_s7/
this is good
https://www.amazon.com/Sanyo-Denki-SAN-Ace-120mm/dp/B00QWB1X3O/ref=sr_1_1?
I had a case of these,but all gone
https://www.amazon.com/Sanyo-Denki-SAN-Ace-120mm/dp/B00YOC80IO/ref=sr_1_2?
You sould periodically clean your miners as dust builds up and coats the heatsinks and fns as youve found out. Switch it off and clean everything and see how you get on.
i did it.. but one of the fan is still slow.. its stuck on 1800rpm and wont increase
You sould periodically clean your miners as dust builds up and coats the heatsinks and fns as youve found out. Switch it off and clean everything and see how you get on.
so its a normal behaviour for a diying fan ?
it goes from 1680 to 3700 rpm.. it was working at like 4500 without droping..
EDIT: after cleaning it it works now.. but now the other one is slower.. wtf
it goes from 1680 to 3700 rpm.. it was working at like 4500 without droping..
EDIT: after cleaning it it works now.. but now the other one is slower.. wtf
Either the fan itself is seizing up or its already dead and being spun by the front fan. Replace the fan and you should be good to go. Make sure your replacement fan can spin at least 4500 rpm, the firmware doesnt like anything under that.
You'll probably have to replace it or find a way to repair it. Looks like a physical issue on the fan itself.
hi im having problem with my antminer S9
one of the fans is running realy low and its making my miner go to temps above 88 grades
heres a pic
https://s24.postimg.org/5nyr76jjn/Untitled.jpg
this miner been running for like 2 months and no problems
both fans turns on but one is realy slow
one of the fans is running realy low and its making my miner go to temps above 88 grades
heres a pic
https://s24.postimg.org/5nyr76jjn/Untitled.jpg
this miner been running for like 2 months and no problems
both fans turns on but one is realy slow
Jump to: