Bitcoin Forum>Bitcoin>Mining>Mining support
Author

Topic: Antminer S9J Problem (Read 176 times)

mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
Antminer S9J Problem
December 16, 2019, 05:21:43 AM
#5
You getting 16.5th on S9 means you are overclocking the hell out of it  Grin

There are two reasons why would one hashboard shows 0 asics.

1- high frequency.

Not all boards can handle the same frequency, to solve this , you need to lower the frequency.

2- one or more chip/s are dying on that board, you will need some tools and skills and a spare chip to fix that, not worth doing now that these gears are pretty cheap, but it is your call.
philipma1957
legendary
Activity: 4326
Merit: 8950
'The right to privacy matters'
Re: Antminer S9J Problem
December 15, 2019, 08:08:39 PM
#4
you lost your ethernet connction  so do you have hard wired ethernet?  if so first try a new cable.

next  when a board goes out like yours   it simply may be dead or close to dying.

Or it like a very clean ethernet conection which you dropped.

once you try a new cable if problem  is still occurred.

try disconnection of one board via   the 3 jacks for pcie.

j   j  j
j   j  j
j   j  j

see if this makes  2 good and 1 dead  run it for hours.   if it makes 2 dead boards  it means the first one is  a good board move on.

j  j   j
j  j   j
j  j   j

try this pattern     if it makes 2 dead boards it means  the third one is good and the middle board is dead

if it makes 1 dead board it means the discount board is the dead one.

once you are certain the correct board that has issues and is sometimes dead mark it with a little piece of tape.

now only hook the dead board to the pcie power cables.
make sure the 2 good board have the pcie cables disconnected.
also make sure the good boards are not connected via the white controller wires.

boot  with just the know dead board and one set of the controller wires.

never detach the controller wires from the controller.

if still dead

uplug the controller wire from the dead board.

pick one of the two loose ended controller wires  and put into the dead board boot.

if dead   the board is dead and needs repair.

if you can  still do firmware updates try braiins  it may work.

If not look for a repair guy.

good luck.
Aminihaan
newbie
Activity: 4
Merit: 0
Re: Antminer S9J Problem
December 15, 2019, 06:49:35 PM
#3
Thanks a loooooot

May I ask another question ?
I have this S9J with these boards:

Code:
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 0 asic

gettin 16.5 Th/s right now, but sometimes 2/3 of that. so prob is the third hash board, right ? how can I know what that problem is ?

Code:
[    0.337455] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.337699] NET: Registered protocol family 1
[    0.338040] RPC: Registered named UNIX socket transport module.
[    0.338054] RPC: Registered udp transport module.
[    0.338062] RPC: Registered tcp transport module.
[    0.338070] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.338082] PCI: CLS 0 bytes, default 64
[    0.338510] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.340527] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.342608] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.342799] msgmni has been set to 967
[    0.343563] io scheduler noop registered
[    0.343576] io scheduler deadline registered
[    0.343617] io scheduler cfq registered (default)
[    0.355232] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.355252] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.480004] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.047389] console [ttyPS0] enabled
[    1.051655] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.059268] [drm] Initialized drm 1.1.0 20060810
[    1.076226] brd: module loaded
[    1.085596] loop: module loaded
[    1.095018] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.100841] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.108747] libphy: XEMACPS mii bus: probed
[    1.113115] ------------- phy_id = 0x3625e62
[    1.118142] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.126776] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.133398] ehci-pci: EHCI PCI platform driver
[    1.140649] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.147490] usbcore: registered new interface driver usb-storage
[    1.154333] mousedev: PS/2 mouse device common for all mice
[    1.160445] i2c /dev entries driver
[    1.167428] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.172902] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.178820] Xilinx Zynq CpuIdle Driver started
[    1.183662] sdhci: Secure Digital Host Controller Interface driver
[    1.189907] sdhci: Copyright(c) Pierre Ossman
[    1.194177] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.200998] mmc0: no vqmmc regulator found
[    1.205013] mmc0: no vmmc regulator found
[    1.246415] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.255106] usbcore: registered new interface driver usbhid
[    1.260617] usbhid: USB HID core driver
[    1.265325] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.271625] nand: Micron MT29F2G08ABAEAWP
[    1.275590] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.281530] Bad block table found at page 131008, version 0x01
[    1.287758] Bad block table found at page 130944, version 0x01
[    1.293807] 3 ofpart partitions found on MTD device pl353-nand
..
.

[   25.735803]
[   25.735803] bcm54xx_config_init
[   26.825690]
[   26.825690] bcm54xx_config_init
[   29.826227] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   29.832246] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  497.154025] random: nonblocking pool is initialized
log_level = 4
This is XILINX board. Totalram:       507486208
Detect 512MB control board of XILINX
mmap axi_fpga_addr = 0xb6f81000
axi_fpga_addr data = 0xc51e
mmap fpga_mem_addr = 0xb5d7a000
forceFreq=-1 forceFlag=0
min work minertest[0]:912


DETECT HW version=0000c51e
miner ID : 80784d006f90481c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
read pic freq and badcore num...
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[26] has core num=1
Check chain[5] PIC fw version=0x03
read pic freq and badcore num...
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[4] has core num=1
Chain[6] ASIC[13] has core num=8
Chain[6] ASIC[14] has core num=1
Chain[6] ASIC[16] has core num=1
Chain[6] ASIC[22] has core num=1
Chain[6] ASIC[23] has core num=3
Chain[6] ASIC[29] has core num=8
Chain[6] ASIC[33] has core num=2
Chain[6] ASIC[46] has core num=1
Chain[6] ASIC[53] has core num=2
Chain[6] ASIC[56] has core num=1
Chain[6] ASIC[57] has core num=2
Chain[6] ASIC[62] has core num=1
Check chain[6] PIC fw version=0x03
read pic freq and badcore num...
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[10] has core num=1
Chain[7] ASIC[21] has core num=1
Check chain[7] PIC fw version=0x03
get PIC voltage=108 on chain[5], value=880
get PIC voltage=108 on chain[6], value=880
get PIC voltage=108 on chain[7], value=880
chain[5] temp offset record: 62,0,0,0,0,0,36,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,36,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,37,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
total_exist_chain_num = 3
single_board_frq_tuning enter
min_rate, des_rate, fix_volt:13800, 14000, 880
force_freq not set, don't need tuning
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1831 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found=30240 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found=28016 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri May 31 11:01:56 CST 2019 type: Antminer S9j
miner ID : 80784d006f90481c
Checking fans...
get fan[4] speed=5280
get fan[4] speed=5280
get fan[5] speed=4440
get fan[4] speed=5280
get fan[5] speed=4440
get fan[4] speed=5280
get fan[5] speed=4440
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has backup chain_voltage=860
No scan based on domain
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
.
.
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=860
No scan based on domain
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
.
.
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=860
No scan based on domain
Check chain[7] PIC fw version=0x03
total_exist_chain_num = 3
Chain[J6] original vol value=860 adjusted vol value:870
Chain[J6] orignal chain_voltage_pic=23 value=930
Chain[J6] original chain_voltage_value=860 adjusted chain_voltage_value:870, value=930
Chain[J6] will use backup chain_voltage_pic=870 [125]
Chain[J6] get working chain_voltage_pic=125
.
.
.
.
.
.
.
Chain[J8] Aisc[62] original freq=675 adjusted freq:768
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 0 asic
retry Chain[J8] has 16 asic
retry Chain[J8] has 53 asic
retry Chain[J8] has 15 asic
retry Chain[J8] has 26 asic
retry Chain[J8] has 0 asic
retry Chain[J8] has 54 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[26] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[4] has core num=1
Chain[J7] ASIC[13] has core num=8
Chain[J7] ASIC[14] has core num=1
Chain[J7] ASIC[16] has core num=1
Chain[J7] ASIC[22] has core num=1
Chain[J7] ASIC[23] has core num=3
Chain[J7] ASIC[29] has core num=8
Chain[J7] ASIC[33] has core num=2
Chain[J7] ASIC[46] has core num=1
Chain[J7] ASIC[53] has core num=2
Chain[J7] ASIC[56] has core num=1
Chain[J7] ASIC[57] has core num=2
Chain[J7] ASIC[62] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[10] has core num=1
Chain[J8] ASIC[21] has core num=1
miner total rate=16570GH/s ideal_total_hash_rate = 16500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:768
.
.
Chain:5 max freq=768
Chain:5 min freq=768

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:775.
.
.
Chain:6 max freq=775
Chain:6 min freq=775

read PIC voltage=940 on chain[7]
Chain:7 chipnum=54
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
.
.
Chain:7 max freq=768
Chain:7 min freq=768


Miner fix freq ...
totalRate = 16570, fixed_totalRate = 16665
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:768 Asic[ 1]:768
.
.
Chain:5 max freq=768
Chain:5 min freq=768

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:775 Asic[ 1]:775
.
.
Chain:6 max freq=775
Chain:6 min freq=775

read PIC voltage=940 on chain[7]
Chain:7 chipnum=54
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
Asic[ 0]:768
.
.

Chain:7 max freq=768
Chain:7 min freq=768

max freq = 775
totalRate = 16570, fixed_totalRate = 16500
set baud=1
Chain[J6] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:21 remote:23 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=55
Chain[J7] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:19 remote:21 offset:27
Chain[J7] chip[244] get middle temp offset=27 typeID=55
single board rate=5515 voltage limit=940 on chain[5]
get PIC voltage=870 on chain[5], check: must be < 940
single board rate=5541 voltage limit=940 on chain[6]
get PIC voltage=870 on chain[6], check: must be < 940
single board rate=5514 voltage limit=940 on chain[7]
get PIC voltage=870 on chain[7], check: must be < 940
setting to working voltage...
chain[5] set voltage to 930
chain[6] set voltage to 930
chain[7] set voltage to 930
chain[5] set voltage to 920
chain[6] set voltage to 920
chain[7] set voltage to 920
chain[5] set voltage to 910
chain[6] set voltage to 910
chain[7] set voltage to 910
chain[5] set voltage to 900
chain[6] set voltage to 900
chain[7] set voltage to 900
chain[5] set voltage to 890
chain[6] set voltage to 890
chain[7] set voltage to 890
chain[5] set voltage to 880
chain[6] set voltage to 880
chain[7] set voltage to 880
chain[5] set voltage to 870
chain[6] set voltage to 870
chain[7] set voltage to 870
start thread for read temp
setStartTimePoint total_tv_start_sys=3109 total_tv_end_sys=3110
restartNum = 2 , auto-reinit enabled...
mining.subscribe:{"id": 0, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer S9j/196500"]}
mining.subscribe:{"id": 8, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer S9j/196500"]}
mining.subscribe:{"id": 9, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer S9j/196500"]}
bring_up_pcb_temp = 41
setting to working voltage...
voltage_check_done
avg hash rate = 11251.666467, ideal hash rate = 16500
hash rate is low...
re_open_core_times: 1
re_open_core enter
Before read Chain[J6] org chain_voltage_pic=125]
After read Chain[J6] new chain_voltage_pic=125 read pic=125
Chain[J6] original vol value=870 adjusted vol value:880
Chain[J6] [org chain_voltage_pic=125 value=870] [new chain_voltage_pic=108 value=880]
Chain[J6] Aisc[00] original freq=768 adjusted freq:768
.
.
.
Before read Chain[J7] org chain_voltage_pic=125]
After read Chain[J7] new chain_voltage_pic=125 read pic=125
Chain[J7] original vol value=870 adjusted vol value:880
Chain[J7] [org chain_voltage_pic=125 value=870] [new chain_voltage_pic=108 value=880]
Chain[J7] Aisc[00] original freq=775 adjusted freq:775
Chain[J7] Aisc[01] original freq=775 adjusted freq:775
.
.
.
Before read Chain[J8] org chain_voltage_pic=125]
After read Chain[J8] new chain_voltage_pic=125 read pic=125
Chain[J8] original vol value=870 adjusted vol value:880
Chain[J8] [org chain_voltage_pic=125 value=870] [new chain_voltage_pic=108 value=880]
Chain[J8] Aisc[00] original freq=768 adjusted freq:768
Chain[J8] Aisc[01] original freq=768 adjusted freq:768
Chain[J8] Aisc[02] original freq=768 adjusted freq:768
.
.
.
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 4 asic
i = 7, retry_count = 0, dev->chain_asic_num[i] = 4
retry Chain[J8] has 61 asic
i = 7, retry_count = 1, dev->chain_asic_num[i] = 61
retry Chain[J8] has 0 asic
i = 7, retry_count = 2, dev->chain_asic_num[i] = 0
retry Chain[J8] has 37 asic
i = 7, retry_count = 3, dev->chain_asic_num[i] = 37
retry Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[26] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[4] has core num=1
Chain[J7] ASIC[13] has core num=8
Chain[J7] ASIC[14] has core num=1
Chain[J7] ASIC[16] has core num=1
Chain[J7] ASIC[22] has core num=1
Chain[J7] ASIC[23] has core num=3
Chain[J7] ASIC[29] has core num=8
Chain[J7] ASIC[33] has core num=2
Chain[J7] ASIC[46] has core num=1
Chain[J7] ASIC[53] has core num=2
Chain[J7] ASIC[56] has core num=1
Chain[J7] ASIC[57] has core num=2
Chain[J7] ASIC[62] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[10] has core num=1
Chain[J8] ASIC[21] has core num=1
miner total rate=16570GH/s ideal_total_hash_rate = 16500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:768 Asic[ 1]:768 Asic[ 2]:768 Asic[ 3]:768 Asic[ 4]:768 Asic[ 5]:768 Asic[ 6]:768 Asic[ 7]:768
Asic[ 8]:768 Asic[ 9]:768 Asic[10]:768 Asic[11]:768 Asic[12]:768 Asic[13]:768 Asic[14]:768 Asic[15]:768
Asic[16]:768 Asic[17]:768 Asic[18]:768 Asic[19]:768 Asic[20]:768 Asic[21]:768 Asic[22]:768 Asic[23]:768
Asic[24]:768 Asic[25]:768 Asic[26]:768 Asic[27]:768 Asic[28]:768 Asic[29]:768 Asic[30]:768 Asic[31]:768
Asic[32]:768 Asic[33]:768 Asic[34]:768 Asic[35]:768 Asic[36]:768 Asic[37]:768 Asic[38]:768 Asic[39]:768
Asic[40]:768 Asic[41]:768 Asic[42]:768 Asic[43]:768 Asic[44]:768 Asic[45]:768 Asic[46]:768 Asic[47]:768
Asic[48]:768 Asic[49]:768 Asic[50]:768 Asic[51]:768 Asic[52]:768 Asic[53]:768 Asic[54]:768 Asic[55]:768
Asic[56]:768 Asic[57]:768 Asic[58]:768 Asic[59]:768 Asic[60]:768 Asic[61]:768 Asic[62]:768
Chain:5 max freq=768
Chain:5 min freq=768

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:775 Asic[ 1]:775 Asic[ 2]:775 Asic[ 3]:775 Asic[ 4]:775 Asic[ 5]:775 Asic[ 6]:775 Asic[ 7]:775
Asic[ 8]:775 Asic[ 9]:775 Asic[10]:775 Asic[11]:775 Asic[12]:775 Asic[13]:775 Asic[14]:775 Asic[15]:775
Asic[16]:775 Asic[17]:775 Asic[18]:775 Asic[19]:775 Asic[20]:775 Asic[21]:775 Asic[22]:775 Asic[23]:775
Asic[24]:775 Asic[25]:775 Asic[26]:775 Asic[27]:775 Asic[28]:775 Asic[29]:775 Asic[30]:775 Asic[31]:775
Asic[32]:775 Asic[33]:775 Asic[34]:775 Asic[35]:775 Asic[36]:775 Asic[37]:775 Asic[38]:775 Asic[39]:775
Asic[40]:775 Asic[41]:775 Asic[42]:775 Asic[43]:775 Asic[44]:775 Asic[45]:775 Asic[46]:775 Asic[47]:775
Asic[48]:775 Asic[49]:775 Asic[50]:775 Asic[51]:775 Asic[52]:775 Asic[53]:775 Asic[54]:775 Asic[55]:775
Asic[56]:775 Asic[57]:775 Asic[58]:775 Asic[59]:775 Asic[60]:775 Asic[61]:775 Asic[62]:775
Chain:6 max freq=775
Chain:6 min freq=775

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
Asic[ 0]:768 Asic[ 1]:768 Asic[ 2]:768 Asic[ 3]:768 Asic[ 4]:768 Asic[ 5]:768 Asic[ 6]:768 Asic[ 7]:768
Asic[ 8]:768 Asic[ 9]:768 Asic[10]:768 Asic[11]:768 Asic[12]:768 Asic[13]:768 Asic[14]:768 Asic[15]:768
Asic[16]:768 Asic[17]:768 Asic[18]:768 Asic[19]:768 Asic[20]:768 Asic[21]:768 Asic[22]:768 Asic[23]:768
Asic[24]:768 Asic[25]:768 Asic[26]:768 Asic[27]:768 Asic[28]:768 Asic[29]:768 Asic[30]:768 Asic[31]:768
Asic[32]:768 Asic[33]:768 Asic[34]:768 Asic[35]:768 Asic[36]:768 Asic[37]:768 Asic[38]:768 Asic[39]:768
Asic[40]:768 Asic[41]:768 Asic[42]:768 Asic[43]:768 Asic[44]:768 Asic[45]:768 Asic[46]:768 Asic[47]:768
Asic[48]:768 Asic[49]:768 Asic[50]:768 Asic[51]:768 Asic[52]:768 Asic[53]:768 Asic[54]:768 Asic[55]:768
Asic[56]:768 Asic[57]:768 Asic[58]:768 Asic[59]:768 Asic[60]:768 Asic[61]:768 Asic[62]:768
Chain:7 max freq=768
Chain:7 min freq=768


Miner fix freq ...
totalRate = 16570, fixed_totalRate = 16665
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:768 Asic[ 1]:768 Asic[ 2]:768 Asic[ 3]:768 Asic[ 4]:768 Asic[ 5]:768 Asic[ 6]:768 Asic[ 7]:768
Asic[ 8]:768 Asic[ 9]:768 Asic[10]:768 Asic[11]:768 Asic[12]:768 Asic[13]:768 Asic[14]:768 Asic[15]:768
Asic[16]:768 Asic[17]:768 Asic[18]:768 Asic[19]:768 Asic[20]:768 Asic[21]:768 Asic[22]:768 Asic[23]:768
Asic[24]:768 Asic[25]:768 Asic[26]:768 Asic[27]:768 Asic[28]:768 Asic[29]:768 Asic[30]:768 Asic[31]:768
Asic[32]:768 Asic[33]:768 Asic[34]:768 Asic[35]:768 Asic[36]:768 Asic[37]:768 Asic[38]:768 Asic[39]:768
Asic[40]:768 Asic[41]:768 Asic[42]:768 Asic[43]:768 Asic[44]:768 Asic[45]:768 Asic[46]:768 Asic[47]:768
Asic[48]:768 Asic[49]:768 Asic[50]:768 Asic[51]:768 Asic[52]:768 Asic[53]:768 Asic[54]:768 Asic[55]:768
Asic[56]:768 Asic[57]:768 Asic[58]:768 Asic[59]:768 Asic[60]:768 Asic[61]:768 Asic[62]:768
Chain:5 max freq=768
Chain:5 min freq=768

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:775 Asic[ 1]:775 Asic[ 2]:775 Asic[ 3]:775 Asic[ 4]:775 Asic[ 5]:775 Asic[ 6]:775 Asic[ 7]:775
Asic[ 8]:775 Asic[ 9]:775 Asic[10]:775 Asic[11]:775 Asic[12]:775 Asic[13]:775 Asic[14]:775 Asic[15]:775
Asic[16]:775 Asic[17]:775 Asic[18]:775 Asic[19]:775 Asic[20]:775 Asic[21]:775 Asic[22]:775 Asic[23]:775
Asic[24]:775 Asic[25]:775 Asic[26]:775 Asic[27]:775 Asic[28]:775 Asic[29]:775 Asic[30]:775 Asic[31]:775
Asic[32]:775 Asic[33]:775 Asic[34]:775 Asic[35]:775 Asic[36]:775 Asic[37]:775 Asic[38]:775 Asic[39]:775
Asic[40]:775 Asic[41]:775 Asic[42]:775 Asic[43]:775 Asic[44]:775 Asic[45]:775 Asic[46]:775 Asic[47]:775
Asic[48]:775 Asic[49]:775 Asic[50]:775 Asic[51]:775 Asic[52]:775 Asic[53]:775 Asic[54]:775 Asic[55]:775
Asic[56]:775 Asic[57]:775 Asic[58]:775 Asic[59]:775 Asic[60]:775 Asic[61]:775 Asic[62]:775
Chain:6 max freq=775
Chain:6 min freq=775

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
Asic[ 0]:768 Asic[ 1]:768
.
.

Chain:7 max freq=768
Chain:7 min freq=768

max freq = 775
totalRate = 16570, fixed_totalRate = 16500
set baud=1
Chain[J6] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:32 remote:33 offset:29
Chain[J6] chip[244] get middle temp offset=29 typeID=55
Chain[J7] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:29 remote:31 offset:28
Chain[J7] chip[244] get middle temp offset=28 typeID=55
Chain[J8] PIC temp offset: 62,0,0,0,0,0,37,28,0,0,0,0,0,0,0,0,0,0,
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=00
Warning: Chain[J8] has no temp offset in PIC! will fix it
Chain[J8] use default temp chip[244]
Chain[J8] try read temp chip[244] ID=00 (I2C addr=0x98)
Chain[J8] try read temp chip[244] ID=00 (I2C addr=0x9A)
Chain[J8] try read temp chip[244] ID=00 (I2C addr=0x9C)
New offset Chain[8] chip[244] local:-64 remote:-64 offset:21
Chain[J8] chip[244] get middle temp offset=21 typeID=00
setting to working voltage...
chain[5] set voltage to 930
chain[6] set voltage to 930
chain[7] set voltage to 930
chain[5] set voltage to 920
chain[6] set voltage to 920
chain[7] set voltage to 920
chain[5] set voltage to 910
chain[6] set voltage to 910
chain[7] set voltage to 910
chain[5] set voltage to 900
chain[6] set voltage to 900
chain[7] set voltage to 900
chain[5] set voltage to 890
chain[6] set voltage to 890
chain[7] set voltage to 890
chain[5] set voltage to 880
chain[6] set voltage to 880
chain[7] set voltage to 880
reopen core end
re_open_core_times: 2
re_open_core enter
Before read Chain[J6] org chain_voltage_pic=108]
After read Chain[J6] new chain_voltage_pic=108 read pic=108
Chain[J6] original vol value=880 adjusted vol value:880
.
.
.
Before read Chain[J7] org chain_voltage_pic=108]
After read Chain[J7] new chain_voltage_pic=108 read pic=108
Chain[J7] original vol value=880 adjusted vol value:880
.
.
.
Before read Chain[J8] org chain_voltage_pic=108]
After read Chain[J8] new chain_voltage_pic=108 read pic=108
C.
.
.
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[26] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[4] has core num=1
Chain[J7] ASIC[13] has core num=8
Chain[J7] ASIC[14] has core num=1
Chain[J7] ASIC[16] has core num=1
Chain[J7] ASIC[22] has core num=1
Chain[J7] ASIC[23] has core num=3
Chain[J7] ASIC[29] has core num=8
Chain[J7] ASIC[33] has core num=2
Chain[J7] ASIC[46] has core num=1
Chain[J7] ASIC[53] has core num=2
Chain[J7] ASIC[56] has core num=1
Chain[J7] ASIC[57] has core num=2
Chain[J7] ASIC[62] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[10] has core num=1
Chain[J8] ASIC[21] has core num=1
miner total rate=16305GH/s ideal_total_hash_rate = 16000GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:756 Asic[ 1]:756 Asic[ 2]:756 Asic[ 3]:756 Asic[ 4]:756 Asic[ 5]:756 Asic[ 6]:756 Asic[ 7]:756
Asic[ 8]:756 Asic[ 9]:756 Asic[10]:756 Asic[11]:756 Asic[12]:756 Asic[13]:756 Asic[14]:756 Asic[15]:756
Asic[16]:756 Asic[17]:756 Asic[18]:756 Asic[19]:756 Asic[20]:756 Asic[21]:756 Asic[22]:756 Asic[23]:756
Asic[24]:756 Asic[25]:756 Asic[26]:756 Asic[27]:756 Asic[28]:756 Asic[29]:756 Asic[30]:756 Asic[31]:756
Asic[32]:756 Asic[33]:756 Asic[34]:756 Asic[35]:756 Asic[36]:756 Asic[37]:756 Asic[38]:756 Asic[39]:756
Asic[40]:756 Asic[41]:756 Asic[42]:756 Asic[43]:756 Asic[44]:756 Asic[45]:756 Asic[46]:756 Asic[47]:756
Asic[48]:756 Asic[49]:756 Asic[50]:756 Asic[51]:756 Asic[52]:756 Asic[53]:756 Asic[54]:756 Asic[55]:756
Asic[56]:756 Asic[57]:756 Asic[58]:756 Asic[59]:756 Asic[60]:756 Asic[61]:756 Asic[62]:756
Chain:5 max freq=756
Chain:5 min freq=756

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:762 Asic[ 1]:762 Asic[ 2]:762 Asic[ 3]:762 Asic[ 4]:762 Asic[ 5]:762 Asic[ 6]:762 Asic[ 7]:762
Asic[ 8]:762 Asic[ 9]:762 Asic[10]:762 Asic[11]:762 Asic[12]:762 Asic[13]:762 Asic[14]:762 Asic[15]:762
Asic[16]:762 Asic[17]:762 Asic[18]:762 Asic[19]:762 Asic[20]:762 Asic[21]:762 Asic[22]:762 Asic[23]:762
Asic[24]:762 Asic[25]:762 Asic[26]:762 Asic[27]:762 Asic[28]:762 Asic[29]:762 Asic[30]:762 Asic[31]:762
Asic[32]:762 Asic[33]:762 Asic[34]:762 Asic[35]:762 Asic[36]:762 Asic[37]:762 Asic[38]:762 Asic[39]:762
Asic[40]:762 Asic[41]:762 Asic[42]:762 Asic[43]:762 Asic[44]:762 Asic[45]:762 Asic[46]:762 Asic[47]:762
Asic[48]:762 Asic[49]:762 Asic[50]:762 Asic[51]:762 Asic[52]:762 Asic[53]:762 Asic[54]:762 Asic[55]:762
Asic[56]:762 Asic[57]:762 Asic[58]:762 Asic[59]:762 Asic[60]:762 Asic[61]:762 Asic[62]:762
Chain:6 max freq=762
Chain:6 min freq=762

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
Asic[ 0]:756 Asic[ 1]:756 Asic[ 2]:756 Asic[ 3]:756 Asic[ 4]:756 Asic[ 5]:756 Asic[ 6]:756 Asic[ 7]:756
Asic[ 8]:756 Asic[ 9]:756 Asic[10]:756 Asic[11]:756 Asic[12]:756 Asic[13]:756 Asic[14]:756 Asic[15]:756
Asic[16]:756 Asic[17]:756 Asic[18]:756 Asic[19]:756 Asic[20]:756 Asic[21]:756 Asic[22]:756 Asic[23]:756
Asic[24]:756 Asic[25]:756 Asic[26]:756 Asic[27]:756 Asic[28]:756 Asic[29]:756 Asic[30]:756 Asic[31]:756
Asic[32]:756 Asic[33]:756 Asic[34]:756 Asic[35]:756 Asic[36]:756 Asic[37]:756 Asic[38]:756 Asic[39]:756
Asic[40]:756 Asic[41]:756 Asic[42]:756 Asic[43]:756 Asic[44]:756 Asic[45]:756 Asic[46]:756 Asic[47]:756
Asic[48]:756 Asic[49]:756 Asic[50]:756 Asic[51]:756 Asic[52]:756 Asic[53]:756 Asic[54]:756 Asic[55]:756
Asic[56]:756 Asic[57]:756 Asic[58]:756 Asic[59]:756 Asic[60]:756 Asic[61]:756 Asic[62]:756
Chain:7 max freq=756
Chain:7 min freq=756


Miner fix freq ...
totalRate = 16305, fixed_totalRate = 16160
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:756 Asic[ 1]:756 Asic[ 2]:756 Asic[ 3]:756 Asic[ 4]:756 Asic[ 5]:756 Asic[ 6]:756 Asic[ 7]:756
Asic[ 8]:756 Asic[ 9]:756 Asic[10]:756 Asic[11]:756 Asic[12]:756 Asic[13]:756 Asic[14]:756 Asic[15]:756
Asic[16]:756 Asic[17]:756 Asic[18]:756 Asic[19]:756 Asic[20]:756 Asic[21]:756 Asic[22]:756 Asic[23]:756
Asic[24]:756 Asic[25]:756 Asic[26]:756 Asic[27]:756 Asic[28]:756 Asic[29]:756 Asic[30]:756 Asic[31]:756
Asic[32]:756 Asic[33]:756 Asic[34]:756 Asic[35]:756 Asic[36]:756 Asic[37]:756 Asic[38]:756 Asic[39]:756
Asic[40]:756 Asic[41]:756 Asic[42]:756 Asic[43]:756 Asic[44]:756 Asic[45]:756 Asic[46]:756 Asic[47]:756
Asic[48]:756 Asic[49]:756 Asic[50]:756 Asic[51]:756 Asic[52]:756 Asic[53]:756 Asic[54]:756 Asic[55]:756
Asic[56]:756 Asic[57]:756 Asic[58]:756 Asic[59]:756 Asic[60]:756 Asic[61]:756 Asic[62]:756
Chain:5 max freq=756
Chain:5 min freq=756

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:762 Asic[ 1]:762 Asic[ 2]:762 Asic[ 3]:762 Asic[ 4]:762 Asic[ 5]:762 Asic[ 6]:762 Asic[ 7]:762
Asic[ 8]:762 Asic[ 9]:762 Asic[10]:762 Asic[11]:762 Asic[12]:762 Asic[13]:762 Asic[14]:762 Asic[15]:762
Asic[16]:762 Asic[17]:762 Asic[18]:762 Asic[19]:762 Asic[20]:762 Asic[21]:762 Asic[22]:762 Asic[23]:762
Asic[24]:762 Asic[25]:762 Asic[26]:762 Asic[27]:762 Asic[28]:762 Asic[29]:762 Asic[30]:762 Asic[31]:762
Asic[32]:762 Asic[33]:762 Asic[34]:762 Asic[35]:762 Asic[36]:762 Asic[37]:762 Asic[38]:762 Asic[39]:762
Asic[40]:762 Asic[41]:762 Asic[42]:762 Asic[43]:762 Asic[44]:762 Asic[45]:762 Asic[46]:762 Asic[47]:762
Asic[48]:762 Asic[49]:762 Asic[50]:762 Asic[51]:762 Asic[52]:762 Asic[53]:762 Asic[54]:762 Asic[55]:762
Asic[56]:762 Asic[57]:762 Asic[58]:762 Asic[59]:762 Asic[60]:762 Asic[61]:762 Asic[62]:762
Chain:6 max freq=762
Chain:6 min freq=762

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
Asic[ 0]:756 Asic[ 1]:756 Asic[ 2]:756 Asic[ 3]:756 Asic[ 4]:756 Asic[ 5]:756 Asic[ 6]:756 Asic[ 7]:756
Asic[ 8]:756 Asic[ 9]:756 Asic[10]:756 Asic[11]:756 Asic[12]:756 Asic[13]:756 Asic[14]:756 Asic[15]:756
Asic[16]:756 Asic[17]:756 Asic[18]:756 Asic[19]:756 Asic[20]:756 Asic[21]:756 Asic[22]:756 Asic[23]:756
Asic[24]:756 Asic[25]:756 Asic[26]:756 Asic[27]:756 Asic[28]:756 Asic[29]:756 Asic[30]:756 Asic[31]:756
Asic[32]:756 Asic[33]:756 Asic[34]:756 Asic[35]:756 Asic[36]:756 Asic[37]:756 Asic[38]:756 Asic[39]:756
Asic[40]:756 Asic[41]:756 Asic[42]:756 Asic[43]:756 Asic[44]:756 Asic[45]:756 Asic[46]:756 Asic[47]:756
Asic[48]:756 Asic[49]:756 Asic[50]:756 Asic[51]:756 Asic[52]:756 Asic[53]:756 Asic[54]:756 Asic[55]:756
Asic[56]:756 Asic[57]:756 Asic[58]:756 Asic[59]:756 Asic[60]:756 Asic[61]:756 Asic[62]:756
Chain:7 max freq=756
Chain:7 min freq=756

max freq = 762
totalRate = 16305, fixed_totalRate = 16000
set baud=1
Chain[J6] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:42 remote:42 offset:31
Chain[J6] chip[244] get middle temp offset=31 typeID=55
Chain[J7] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:38 remote:40 offset:29
Chain[J7] chip[244] get middle temp offset=29 typeID=55
Chain[J8] PIC temp offset: 62,0,0,0,0,0,37,28,0,0,0,0,0,0,0,0,0,0,
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=00
Warning: Chain[J8] has no temp offset in PIC! will fix it
Chain[J8] use default temp chip[244]
Chain[J8] try read temp chip[244] ID=00 (I2C addr=0x98)
Chain[J8] try read temp chip[244] ID=00 (I2C addr=0x9A)
Chain[J8] try read temp chip[244] ID=00 (I2C addr=0x9C)
New offset Chain[8] chip[244] local:-64 remote:-64 offset:21
Chain[J8] chip[244] get middle temp offset=21 typeID=00
setting to working voltage...
chain[5] set voltage to 930
chain[6] set voltage to 930
chain[7] set voltage to 930
chain[5] set voltage to 920
chain[6] set voltage to 920
chain[7] set voltage to 920
chain[5] set voltage to 910
chain[6] set voltage to 910
chain[7] set voltage to 910
chain[5] set voltage to 900
chain[6] set voltage to 900
chain[7] set voltage to 900
chain[5] set voltage to 890
chain[6] set voltage to 890
chain[7] set voltage to 890
chain[5] set voltage to 880
chain[6] set voltage to 880
chain[7] set voltage to 880
reopen core end
avg_rate = 11094, ideal_total_hash_rate = 16000
re_open_core_times: 3
re_open_core enter
Before read Chain[J6] org chain_voltage_pic=108]
After read Chain[J6] new chain_voltage_pic=108 read pic=108
Chain[J6] used up the adjustable Vol idx:3!!
Chain[J6] used up the adjustable Freq idx:3!!
Before read Chain[J7] org chain_voltage_pic=108]
After read Chain[J7] new chain_voltage_pic=108 read pic=108
Chain[J7] used up the adjustable Vol idx:3!!
Chain[J7] used up the adjustable Freq idx:3!!
Before read Chain[J8] org chain_voltage_pic=108]
After read Chain[J8] new chain_voltage_pic=108 read pic=108
Chain[J8] used up the adjustable Vol idx:3!!
Chain[J8] used up the adjustable Freq idx:3!!
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[26] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[4] has core num=1
Chain[J7] ASIC[13] has core num=8
Chain[J7] ASIC[14] has core num=1
Chain[J7] ASIC[16] has core num=1
Chain[J7] ASIC[22] has core num=1
Chain[J7] ASIC[23] has core num=3
Chain[J7] ASIC[29] has core num=8
Chain[J7] ASIC[33] has core num=2
Chain[J7] ASIC[46] has core num=1
Chain[J7] ASIC[53] has core num=2
Chain[J7] ASIC[56] has core num=1
Chain[J7] ASIC[57] has core num=2
Chain[J7] ASIC[62] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[10] has core num=1
Chain[J8] ASIC[21] has core num=1
miner total rate=16001GH/s ideal_total_hash_rate = 16000GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:737 Asic[ 1]:737 Asic[ 2]:737 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:743 Asic[37]:743 Asic[38]:743 Asic[39]:743
Asic[40]:743 Asic[41]:743 Asic[42]:743 Asic[43]:743 Asic[44]:743 Asic[45]:743 Asic[46]:743 Asic[47]:743
Asic[48]:743 Asic[49]:743 Asic[50]:743 Asic[51]:743 Asic[52]:743 Asic[53]:743 Asic[54]:743 Asic[55]:743
Asic[56]:743 Asic[57]:743 Asic[58]:743 Asic[59]:743 Asic[60]:743 Asic[61]:743 Asic[62]:743
Chain:5 max freq=743
Chain:5 min freq=737

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:743 Asic[ 1]:743 Asic[ 2]:743 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:750 Asic[37]:750 Asic[38]:750 Asic[39]:750
Asic[40]:750 Asic[41]:750 Asic[42]:750 Asic[43]:750 Asic[44]:750 Asic[45]:750 Asic[46]:750 Asic[47]:750
Asic[48]:750 Asic[49]:750 Asic[50]:750 Asic[51]:750 Asic[52]:750 Asic[53]:750 Asic[54]:750 Asic[55]:750
Asic[56]:750 Asic[57]:750 Asic[58]:750 Asic[59]:750 Asic[60]:750 Asic[61]:750 Asic[62]:750
Chain:6 max freq=750
Chain:6 min freq=743

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
Asic[ 0]:737 Asic[ 1]:743 Asic[ 2]:743 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:743 Asic[37]:743 Asic[38]:743 Asic[39]:743
Asic[40]:743 Asic[41]:743 Asic[42]:743 Asic[43]:743 Asic[44]:743 Asic[45]:743 Asic[46]:743 Asic[47]:743
Asic[48]:743 Asic[49]:743 Asic[50]:743 Asic[51]:743 Asic[52]:743 Asic[53]:743 Asic[54]:743 Asic[55]:743
Asic[56]:743 Asic[57]:743 Asic[58]:743 Asic[59]:743 Asic[60]:743 Asic[61]:743 Asic[62]:743
Chain:7 max freq=743
Chain:7 min freq=737


Miner fix freq ...
totalRate = 16001, fixed_totalRate = 16160
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:737 Asic[ 1]:737 Asic[ 2]:737 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:743 Asic[37]:743 Asic[38]:743 Asic[39]:743
Asic[40]:743 Asic[41]:743 Asic[42]:743 Asic[43]:743 Asic[44]:743 Asic[45]:743 Asic[46]:743 Asic[47]:743
Asic[48]:743 Asic[49]:743 Asic[50]:743 Asic[51]:743 Asic[52]:743 Asic[53]:743 Asic[54]:743 Asic[55]:743
Asic[56]:743 Asic[57]:743 Asic[58]:743 Asic[59]:743 Asic[60]:743 Asic[61]:743 Asic[62]:743
Chain:5 max freq=743
Chain:5 min freq=737

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:743 Asic[ 1]:743 Asic[ 2]:743 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:750 Asic[37]:750 Asic[38]:750 Asic[39]:750
Asic[40]:750 Asic[41]:750 Asic[42]:750 Asic[43]:750 Asic[44]:750 Asic[45]:750 Asic[46]:750 Asic[47]:750
Asic[48]:750 Asic[49]:750 Asic[50]:750 Asic[51]:750 Asic[52]:750 Asic[53]:750 Asic[54]:750 Asic[55]:750
Asic[56]:750 Asic[57]:750 Asic[58]:750 Asic[59]:750 Asic[60]:750 Asic[61]:750 Asic[62]:750
Chain:6 max freq=750
Chain:6 min freq=743

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
Asic[ 0]:737 Asic[ 1]:743 Asic[ 2]:743 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:743 Asic[37]:743 Asic[38]:743 Asic[39]:743
Asic[40]:743 Asic[41]:743 Asic[42]:743 Asic[43]:743 Asic[44]:743 Asic[45]:743 Asic[46]:743 Asic[47]:743
Asic[48]:743 Asic[49]:743 Asic[50]:743 Asic[51]:743 Asic[52]:743 Asic[53]:743 Asic[54]:743 Asic[55]:743
Asic[56]:743 Asic[57]:743 Asic[58]:743 Asic[59]:743 Asic[60]:743 Asic[61]:743 Asic[62]:743
Chain:7 max freq=743
Chain:7 min freq=737

max freq = 750
totalRate = 16001, fixed_totalRate = 16000
set baud=1
Chain[J6] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:42 remote:43 offset:30
Chain[J6] chip[244] get middle temp offset=30 typeID=55
Chain[J7] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:40 remote:42 offset:29
Chain[J7] chip[244] get middle temp offset=29 typeID=55
Chain[J8] PIC temp offset: 62,0,0,0,0,0,37,28,0,0,0,0,0,0,0,0,0,0,
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=00
Warning: Chain[J8] has no temp offset in PIC! will fix it
Chain[J8] use default temp chip[244]
Chain[J8] try read temp chip[244] ID=00 (I2C addr=0x98)
Chain[J8] try read temp chip[244] ID=00 (I2C addr=0x9A)
Chain[J8] try read temp chip[244] ID=00 (I2C addr=0x9C)
New offset Chain[8] chip[244] local:-64 remote:-64 offset:21
Chain[J8] chip[244] get middle temp offset=21 typeID=00
setting to working voltage...
chain[5] set voltage to 930
chain[6] set voltage to 930
chain[7] set voltage to 930
chain[5] set voltage to 920
chain[6] set voltage to 920
chain[7] set voltage to 920
chain[5] set voltage to 910
chain[6] set voltage to 910
chain[7] set voltage to 910
chain[5] set voltage to 900
chain[6] set voltage to 900
chain[7] set voltage to 900
chain[5] set voltage to 890
chain[6] set voltage to 890
chain[7] set voltage to 890
chain[5] set voltage to 880
chain[6] set voltage to 880
chain[7] set voltage to 880
reopen core end
re_open_core_times: 4
re_open_core enter
Before read Chain[J6] org chain_voltage_pic=108]
After read Chain[J6] new chain_voltage_pic=108 read pic=108
Chain[J6] used up the adjustable Vol idx:3!!
Chain[J6] used up the adjustable Freq idx:3!!
Before read Chain[J7] org chain_voltage_pic=108]
After read Chain[J7] new chain_voltage_pic=108 read pic=108
Chain[J7] used up the adjustable Vol idx:3!!
Chain[J7] used up the adjustable Freq idx:3!!
Before read Chain[J8] org chain_voltage_pic=108]
After read Chain[J8] new chain_voltage_pic=108 read pic=108
Chain[J8] used up the adjustable Vol idx:3!!
Chain[J8] used up the adjustable Freq idx:3!!
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[26] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[4] has core num=1
Chain[J7] ASIC[13] has core num=8
Chain[J7] ASIC[14] has core num=1
Chain[J7] ASIC[16] has core num=1
Chain[J7] ASIC[22] has core num=1
Chain[J7] ASIC[23] has core num=3
Chain[J7] ASIC[29] has core num=8
Chain[J7] ASIC[33] has core num=2
Chain[J7] ASIC[46] has core num=1
Chain[J7] ASIC[53] has core num=2
Chain[J7] ASIC[56] has core num=1
Chain[J7] ASIC[57] has core num=2
Chain[J7] ASIC[62] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[10] has core num=1
Chain[J8] ASIC[21] has core num=1
miner total rate=16001GH/s ideal_total_hash_rate = 16000GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:737 Asic[ 1]:737 Asic[ 2]:737 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:743 Asic[37]:743 Asic[38]:743 Asic[39]:743
Asic[40]:743 Asic[41]:743 Asic[42]:743 Asic[43]:743 Asic[44]:743 Asic[45]:743 Asic[46]:743 Asic[47]:743
Asic[48]:743 Asic[49]:743 Asic[50]:743 Asic[51]:743 Asic[52]:743 Asic[53]:743 Asic[54]:743 Asic[55]:743
Asic[56]:743 Asic[57]:743 Asic[58]:743 Asic[59]:743 Asic[60]:743 Asic[61]:743 Asic[62]:743
Chain:5 max freq=743
Chain:5 min freq=737

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:743 Asic[ 1]:743 Asic[ 2]:743 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:750 Asic[37]:750 Asic[38]:750 Asic[39]:750
Asic[40]:750 Asic[41]:750 Asic[42]:750 Asic[43]:750 Asic[44]:750 Asic[45]:750 Asic[46]:750 Asic[47]:750
Asic[48]:750 Asic[49]:750 Asic[50]:750 Asic[51]:750 Asic[52]:750 Asic[53]:750 Asic[54]:750 Asic[55]:750
Asic[56]:750 Asic[57]:750 Asic[58]:750 Asic[59]:750 Asic[60]:750 Asic[61]:750 Asic[62]:750
Chain:6 max freq=750
Chain:6 min freq=743

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
Asic[ 0]:737 Asic[ 1]:743 Asic[ 2]:743 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:743 Asic[37]:743 Asic[38]:743 Asic[39]:743
Asic[40]:743 Asic[41]:743 Asic[42]:743 Asic[43]:743 Asic[44]:743 Asic[45]:743 Asic[46]:743 Asic[47]:743
Asic[48]:743 Asic[49]:743 Asic[50]:743 Asic[51]:743 Asic[52]:743 Asic[53]:743 Asic[54]:743 Asic[55]:743
Asic[56]:743 Asic[57]:743 Asic[58]:743 Asic[59]:743 Asic[60]:743 Asic[61]:743 Asic[62]:743
Chain:7 max freq=743
Chain:7 min freq=737


Miner fix freq ...
totalRate = 16001, fixed_totalRate = 16160
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:737 Asic[ 1]:737 Asic[ 2]:737 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:743 Asic[37]:743 Asic[38]:743 Asic[39]:743
Asic[40]:743 Asic[41]:743 Asic[42]:743 Asic[43]:743 Asic[44]:743 Asic[45]:743 Asic[46]:743 Asic[47]:743
Asic[48]:743 Asic[49]:743 Asic[50]:743 Asic[51]:743 Asic[52]:743 Asic[53]:743 Asic[54]:743 Asic[55]:743
Asic[56]:743 Asic[57]:743 Asic[58]:743 Asic[59]:743 Asic[60]:743 Asic[61]:743 Asic[62]:743
Chain:5 max freq=743
Chain:5 min freq=737

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=681
Asic[ 0]:743 Asic[ 1]:743 Asic[ 2]:743 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:750 Asic[37]:750 Asic[38]:750 Asic[39]:750
Asic[40]:750 Asic[41]:750 Asic[42]:750 Asic[43]:750 Asic[44]:750 Asic[45]:750 Asic[46]:750 Asic[47]:750
Asic[48]:750 Asic[49]:750 Asic[50]:750 Asic[51]:750 Asic[52]:750 Asic[53]:750 Asic[54]:750 Asic[55]:750
Asic[56]:750 Asic[57]:750 Asic[58]:750 Asic[59]:750 Asic[60]:750 Asic[61]:750 Asic[62]:750
Chain:6 max freq=750
Chain:6 min freq=743

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=675
Asic[ 0]:737 Asic[ 1]:743 Asic[ 2]:743 Asic[ 3]:743 Asic[ 4]:743 Asic[ 5]:743 Asic[ 6]:743 Asic[ 7]:743
Asic[ 8]:743 Asic[ 9]:743 Asic[10]:743 Asic[11]:743 Asic[12]:743 Asic[13]:743 Asic[14]:743 Asic[15]:743
Asic[16]:743 Asic[17]:743 Asic[18]:743 Asic[19]:743 Asic[20]:743 Asic[21]:743 Asic[22]:743 Asic[23]:743
Asic[24]:743 Asic[25]:743 Asic[26]:743 Asic[27]:743 Asic[28]:743 Asic[29]:743 Asic[30]:743 Asic[31]:743
Asic[32]:743 Asic[33]:743 Asic[34]:743 Asic[35]:743 Asic[36]:743 Asic[37]:743 Asic[38]:743 Asic[39]:743
Asic[40]:743 Asic[41]:743 Asic[42]:743 Asic[43]:743 Asic[44]:743 Asic[45]:743 Asic[46]:743 Asic[47]:743
Asic[48]:743 Asic[49]:743 Asic[50]:743 Asic[51]:743 Asic[52]:743 Asic[53]:743 Asic[54]:743 Asic[55]:743
Asic[56]:743 Asic[57]:743 Asic[58]:743 Asic[59]:743 Asic[60]:743 Asic[61]:743 Asic[62]:743
Chain:7 max freq=743
Chain:7 min freq=737

max freq = 750
totalRate = 16001, fixed_totalRate = 16000
set baud=1
Chain[J6] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[6] chip[244] local:38 remote:38 offset:31
Chain[J6] chip[244] get middle temp offset=31 typeID=55
Chain[J7] PIC temp offset: 62,0,0,0,0,0,36,28,0,0,0,0,0,0,0,0,0,0,
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[7] chip[244] local:35 remote:36 offset:30
Chain[J7] chip[244] get middle temp offset=30 typeID=55
Chain[J8] PIC temp offset: 62,0,0,0,0,0,37,28,0,0,0,0,0,0,0,0,0,0,
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=55
New offset Chain[8] chip[244] local:33 remote:34 offset:29
Chain[J8] chip[244] get middle temp offset=29 typeID=55
setting to working voltage...
chain[5] set voltage to 930
chain[6] set voltage to 930
chain[7] set voltage to 930
chain[5] set voltage to 920
chain[6] set voltage to 920
chain[7] set voltage to 920
chain[5] set voltage to 910
chain[6] set voltage to 910
chain[7] set voltage to 910
chain[5] set voltage to 900
chain[6] set voltage to 900
chain[7] set voltage to 900
chain[5] set voltage to 890
chain[6] set voltage to 890
chain[7] set voltage to 890
chain[5] set voltage to 880
chain[6] set voltage to 880
chain[7] set voltage to 880
reopen core end
avg_rate = 16213, ideal_total_hash_rate = 16000
avg hash rate is OK
avg_rate = 16199, ideal_total_hash_rate = 16000
avg hash rate is OK
avg_rate = 16146, ideal_total_hash_rate = 16000
avg hash rate is OK
avg_rate = 16149, ideal_total_hash_rate = 16000
avg hash rate is OK
avg_rate = 16086, ideal_total_hash_rate = 16000
avg hash rate is OK
Fatal Error: network connection lost!
max pcb temperature:61, fan num:2, error counter:1
Fatal Error: network connection lost!
max pcb temperature:61, fan num:2, error counter:2
Do not clear run bit
Fatal Error: network connection lost!
max pcb temperature:61, fan num:2, error counter:3
Do not clear run bit
Fatal Error: network connection lost!
max pcb temperature:61, fan num:2, error counter:4
Do not clear run bit
Fatal Error: network connection lost!
max pcb temperature:61, fan num:2, error counter:5
Do not clear run bit
Fatal Error: network connection lost!
max pcb temperature:61, fan num:2, error counter:6
Do not clear run bit
Fatal Error: network connection lost!
max pcb temperature:61, fan num:2, error counter:7
Do not clear run bit
Fatal Error: network connection lost!
max pcb temperature:61, fan num:2, error counter:8
Do not clear run bit
mining.subscribe:{"id": 1604, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer S9j/196500", "f088b3cbb2b4e2e9"]}
mining.subscribe:{"id": 1605, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer S9j/196500", "a3f3f13e2555238b"]}
mining.subscribe:{"id": 1606, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer S9j/196500", "032efc28ad2e49fe"]}
Network connection restore.
avg_rate = 16085, ideal_total_hash_rate = 16000
avg hash rate is OK
do read_temp_func once...

get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=80.8320 Asic[02]=81.6540 Asic[03]=84.8420 Asic[04]=87.7440 Asic[05]=83.1810 Asic[06]=84.1880 Asic[07]=83.3490 Asic[08]=81.9230
Asic[09]=75.5310 Asic[10]=89.4720 Asic[11]=84.6410 Asic[12]=81.3020 Asic[13]=84.4900 Asic[14]=85.9490 Asic[15]=93.0960 Asic[16]=85.4120
Asic[17]=88.1130 Asic[18]=88.3650 Asic[19]=78.4500 Asic[20]=84.6240 Asic[21]=85.4290 Asic[22]=86.1670 Asic[23]=92.2240 Asic[24]=88.8350
Asic[25]=80.1950 Asic[26]=90.6300 Asic[27]=81.5200 Asic[28]=79.0540 Asic[29]=76.5540 Asic[30]=81.1680 Asic[31]=88.6340 Asic[32]=85.4790
Asic[33]=80.5470 Asic[34]=79.7750 Asic[35]=89.7070 Asic[36]=81.1680 Asic[37]=81.9900 Asic[38]=81.9060 Asic[39]=83.6000 Asic[40]=81.8050
Asic[41]=84.3550 Asic[42]=86.3350 Asic[43]=80.7310 Asic[44]=87.1910 Asic[45]=83.1640 Asic[46]=88.5330 Asic[47]=87.6270 Asic[48]=86.8380
Asic[49]=81.1840 Asic[50]=87.9960 Asic[51]=85.7810 Asic[52]=77.9130 Asic[53]=87.8280 Asic[54]=80.4460 Asic[55]=81.3860 Asic[56]=86.0330
Asic[57]=87.2070 Asic[58]=85.9320 Asic[59]=84.1200 Asic[60]=85.5970 Asic[61]=82.1580 Asic[62]=87.4420 Asic[63]=88.0630

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=85.7480
.
.

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=87.3420
.
.

Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
Chain[5] Chip[244] pcb temperature=61
Chain[5] Chip[62] junction temperature=70
Special fix Chain[5] Chip[62] middle Temp = 76
Done read temp on Chain[5]
Chain[6] Chip[244] pcb temperature=59
Chain[6] Chip[62] junction temperature=67
Special fix Chain[6] Chip[62] middle Temp = 74
Done read temp on Chain[6]
Chain[7] Chip[244] pcb temperature=57
Chain[7] Chip[62] junction temperature=65
Special fix Chain[7] Chip[62] middle Temp = 72
Done read temp on Chain[7]
Max pcb temp : 61
set FAN speed according to: temp_highest=61 temp_top1[PWM_T]=61 temp_top1[TEMP_POS_LOCAL]=61 temp_change=-1 fix_fan_steps=0
FAN PWM: 74
read_temp_func Done!
CRC error counter=36892
mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
Re: Antminer S9J Problem
December 15, 2019, 05:31:14 PM
#2
Your Kernel Log shows the following:

Code:
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic

Which means the three hashboards are perfect, temp-sensors are also fine, if you are referring to this line

Code:
CRC error counter=106

I have a few miners with the same "issue", it should indicate a problem in one of the aspects of the miner, but it is not always accurate, so as long as you are getting the right hashrate and all boards show 63 Asics, ignore the rest.
Aminihaan
newbie
Activity: 4
Merit: 0
Re: Antminer S9J Problem
December 15, 2019, 04:43:42 PM
#1
Hi,
Hope having a good day/night.

I have a problem with my S9J. Actually the miner is working perfectly (as much as I know!)
But in its Kernel Log I have some errors.
Could you help me to find where the prob is ?

Thanks a lot.

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06da8ac   (6987 kB)
[    0.000000]       .init : 0xc06db000 - 0xc070e380   ( 205 kB)
[    0.000000]       .data : 0xc0710000 - 0xc0757138   ( 285 kB)
[    0.000000]        .bss : 0xc0757144 - 0xc0797bfc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000294] ps7-ttc #0 at df804000, irq=43
[    0.000595] Console: colour dummy device 80x30
[    0.000623] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040199] pid_max: default: 32768 minimum: 301
[    0.040411] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040430] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042597] CPU: Testing write buffer coherency: ok
[    0.042909] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042965] Setting up static identity map for 0x4cb118 - 0x4cb170
[    0.043183] L310 cache controller enabled
[    0.043203] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.120985] CPU1: Booted secondary processor
[    0.210220] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210349] Brought up 2 CPUs
[    0.210368] SMP: Total of 2 processors activated.
[    0.210376] CPU: All CPU(s) started in SVC mode.
[    0.211034] devtmpfs: initialized
[    0.213465] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214651] regulator-dummy: no parameters
[    0.221513] NET: Registered protocol family 16
[    0.223672] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.225941] cpuidle: using governor ladder
[    0.225955] cpuidle: using governor menu
[    0.233338] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.234854] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.234867] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.234979] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.256382] bio: create slab at 0
[    0.257769] vgaarb: loaded
[    0.258466] SCSI subsystem initialized
[    0.259343] usbcore: registered new interface driver usbfs
[    0.259518] usbcore: registered new interface driver hub
[    0.259735] usbcore: registered new device driver usb
[    0.261067] media: Linux media interface: v0.10
[    0.261426] Linux video capture interface: v2.00
[    0.261687] pps_core: LinuxPPS API ver. 1 registered
[    0.261698] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.261827] PTP clock support registered
[    0.262191] EDAC MC: Ver: 3.0.0
[    0.263366] Advanced Linux Sound Architecture Driver Initialized.
[    0.266074] DMA-API: preallocated 4096 debug entries
[    0.266087] DMA-API: debugging enabled by kernel config
[    0.266157] Switched to clocksource arm_global_timer
[    0.285985] NET: Registered protocol family 2
[    0.287014] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.287071] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.287156] TCP: Hash tables configured (established 4096 bind 4096)
[    0.287200] TCP: reno registered
[    0.287216] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.287246] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.287566] NET: Registered protocol family 1
[    0.287903] RPC: Registered named UNIX socket transport module.
[    0.287915] RPC: Registered udp transport module.
[    0.287923] RPC: Registered tcp transport module.
[    0.287932] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.287943] PCI: CLS 0 bytes, default 64
[    0.288365] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.290346] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.292409] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.292599] msgmni has been set to 967
[    0.293353] io scheduler noop registered
[    0.293366] io scheduler deadline registered
[    0.293402] io scheduler cfq registered (default)
[    0.305448] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.305468] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.427037] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.994031] console [ttyPS0] enabled
[    0.998310] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.005902] [drm] Initialized drm 1.1.0 20060810
[    1.022931] brd: module loaded
[    1.032304] loop: module loaded
[    1.041655] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.047473] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.055195] libphy: XEMACPS mii bus: probed
[    1.059874] ------------- phy_id = 0x3625e62
[    1.064604] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.073500] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.080304] ehci-pci: EHCI PCI platform driver
[    1.087531] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.094323] usbcore: registered new interface driver usb-storage
[    1.101205] mousedev: PS/2 mouse device common for all mice
[    1.107309] i2c /dev entries driver
[    1.114192] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.119705] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.125582] Xilinx Zynq CpuIdle Driver started
[    1.130469] sdhci: Secure Digital Host Controller Interface driver
[    1.136653] sdhci: Copyright(c) Pierre Ossman
[    1.140923] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.147739] mmc0: no vqmmc regulator found
[    1.151751] mmc0: no vmmc regulator found
[    1.196178] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.204877] usbcore: registered new interface driver usbhid
[    1.210383] usbhid: USB HID core driver
[    1.215081] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.221379] nand: Micron MT29F2G08ABAEAWP
[    1.225348] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.231296] Bad block table found at page 131008, version 0x01
[    1.237515] Bad block table found at page 130944, version 0x01
[    1.243566] 3 ofpart partitions found on MTD device pl353-nand
[    1.249346] Creating 3 MTD partitions on "pl353-nand":
[    1.254443] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.262481] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.269792] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.280510] TCP: cubic registered
[    1.283747] NET: Registered protocol family 17
[    1.288436] Registering SWP/SWPB emulation handler
[    1.294316] regulator-dummy: disabling
[    1.298645] UBI: attaching mtd1 to ubi0
[    1.825917] UBI: scanning is finished
[    1.837563] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.844614] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.851410] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.858086] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.864924] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.870934] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.878045] UBI: max/mean erase counter: 28/15, WL threshold: 4096, image sequence number: 1358777852
[    1.887249] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.896465] UBI: background thread "ubi_bgt0d" started, PID 1084
[    1.896471] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.900366] ALSA device list:
[    1.900369]   No soundcards found.
[    1.916785] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[    1.945939] UBIFS: recovery needed
[    2.040266] UBIFS: recovery completed
[    2.043929] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.049879] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.058982] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.068870] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.073900] UBIFS: media format: w4/r0 (latest is w4/r0), UUID D111FE0E-B965-4C75-B4AA-11F4FC522746, small LPT model
[    2.084961] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.091915] devtmpfs: mounted
[    2.095016] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[    2.940504] random: dd urandom read with 1 bits of entropy available
[    3.326201]
[    3.326201] bcm54xx_config_init
[    4.386177]
[    4.386177] bcm54xx_config_init
[    7.387048] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.393141] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   40.460894] In axi fpga driver!
[   40.463965] request_mem_region OK!
[   40.467391] AXI fpga dev virtual address is 0xdf9fe000
[   40.472464] *base_vir_addr = 0xc51e
[   40.486778] In fpga mem driver!
[   40.490068] request_mem_region OK!
[   40.493629] fpga mem virtual address is 0xe2000000
[   41.285540]
[   41.285540] bcm54xx_config_init
[   42.385430]
[   42.385430] bcm54xx_config_init
[   45.385936] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   45.391955] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  573.334516] random: nonblocking pool is initialized
log_level = 4
This is XILINX board. Totalram:       507486208
Detect 512MB control board of XILINX
mmap axi_fpga_addr = 0xb6ff4000
axi_fpga_addr data = 0xc51e
mmap fpga_mem_addr = 0xb5ded000
forceFreq=-1 forceFlag=0
min work minertest[0]:912


DETECT HW version=0000c51e
miner ID : 805244806f904814
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
read pic freq and badcore num...
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[4] has core num=4
Chain[5] ASIC[6] has core num=1
Chain[5] ASIC[10] has core num=2
Chain[5] ASIC[43] has core num=1
Chain[5] ASIC[45] has core num=1
Check chain[5] PIC fw version=0x03
read pic freq and badcore num...
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[22] has core num=1
Chain[6] ASIC[26] has core num=15
Chain[6] ASIC[42] has core num=1
Chain[6] ASIC[46] has core num=8
Chain[6] ASIC[54] has core num=1
Check chain[6] PIC fw version=0x03
read pic freq and badcore num...
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[17] has core num=8
Chain[7] ASIC[42] has core num=3
Check chain[7] PIC fw version=0x03
get PIC voltage=108 on chain[5], value=880
get PIC voltage=108 on chain[6], value=880
get PIC voltage=108 on chain[7], value=880
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
total_exist_chain_num = 3
single_board_frq_tuning enter
min_rate, des_rate, fix_volt:13800, 14000, 880
force_freq not set, don't need tuning
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1821 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri May 31 11:01:56 CST 2019 type: Antminer S9j
miner ID : 805244806f904814
Checking fans...
get fan[4] speed=6240
get fan[4] speed=6240
get fan[5] speed=5760
get fan[4] speed=6240
get fan[5] speed=5760
get fan[4] speed=6240
get fan[5] speed=5760
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
last_freq: 0x00 0x7d 0x00 0x4e 0x00 0x4e 0x04 0x4e 0x0e 0x4e 0x00 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x03 0x4e 0x01 0x4e 0x01 0x4e 0x0f 0x4e 0x0f 0x4e 0x0f 0x4e 0x0f 0x4e 0x05 0x4e 0x06 0x4e 0x23 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e 0x00 0x4e
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J6] has backup chain_voltage=860
No scan based on domain
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
last_freq: 0x00 0x7d 0x00 0x50 0x00 0x50 0x05 0x50 0x00 0x50 0x00 0x50 0x03 0x50 0x03 0x50 0x03 0x50 0x03 0x50 0x03 0x50 0x03 0x50 0x01 0x50 0x01 0x50 0x0f 0x50 0x0f 0x50 0x0f 0x50 0x0f 0x50 0x05 0x50 0x06 0x50 0x23 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50 0x00 0x50
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=860
No scan based on domain
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
last_freq: 0x00 0x7d 0x00 0x4f 0x00 0x4f 0x04 0x4f 0x0f 0x4f 0x00 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x03 0x4f 0x01 0x4f 0x01 0x4f 0x0f 0x4f 0x0f 0x4f 0x0f 0x4f 0x0f 0x4f 0x05 0x4f 0x06 0x4f 0x23 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f 0x00 0x4f
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=860
No scan based on domain
Check chain[7] PIC fw version=0x03
total_exist_chain_num = 3
Chain[J6] original vol value=860 adjusted vol value:870
Chain[J6] orignal chain_voltage_pic=108 value=880
Chain[J6] original chain_voltage_value=860 adjusted chain_voltage_value:870, value=880
Chain[J6] will use backup chain_voltage_pic=870 [125]
Chain[J6] get working chain_voltage_pic=125
.
.
.
Chain[J7] original vol value=860 adjusted vol value:870
Chain[J7] orignal chain_voltage_pic=108 value=880
Chain[J7] original chain_voltage_value=860 adjusted chain_voltage_value:870, value=880
Chain[J7] will use backup chain_voltage_pic=870 [125]
Chain[J7] get working chain_voltage_pic=125
.
.
.
Chain[J8] original vol value=860 adjusted vol value:870
Chain[J8] orignal chain_voltage_pic=108 value=880
Chain[J8] original chain_voltage_value=860 adjusted chain_voltage_value:870, value=880
Chain[J8] will use backup chain_voltage_pic=870 [125]
Chain[J8] get working chain_voltage_pic=125.
.
.
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[4] has core num=4
Chain[J6] ASIC[6] has core num=1
Chain[J6] ASIC[10] has core num=2
Chain[J6] ASIC[43] has core num=1
Chain[J6] ASIC[45] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[22] has core num=1
Chain[J7] ASIC[26] has core num=15
Chain[J7] ASIC[42] has core num=1
Chain[J7] ASIC[46] has core num=8
Chain[J7] ASIC[54] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[17] has core num=8
Chain[J8] ASIC[42] has core num=3
miner total rate=16577GH/s ideal_total_hash_rate = 16500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:768 Asic[ 1]:768 Asic[ 2]:768 Asic[ 3]:768 Asic[ 4]:768 Asic[ 5]:768 Asic[ 6]:768 Asic[ 7]:768
Asic[ 8]:768 Asic[ 9]:768 Asic[10]:768 Asic[11]:768 Asic[12]:768 Asic[13]:768 Asic[14]:768 Asic[15]:768
Asic[16]:768 Asic[17]:768 Asic[18]:768 Asic[19]:768 Asic[20]:768 Asic[21]:768 Asic[22]:768 Asic[23]:768
Asic[24]:768 Asic[25]:768 Asic[26]:768 Asic[27]:768 Asic[28]:768 Asic[29]:768 Asic[30]:768 Asic[31]:768
Asic[32]:768 Asic[33]:768 Asic[34]:768 Asic[35]:768 Asic[36]:768 Asic[37]:768 Asic[38]:768 Asic[39]:768
Asic[40]:768 Asic[41]:768 Asic[42]:768 Asic[43]:768 Asic[44]:768 Asic[45]:768 Asic[46]:768 Asic[47]:768
Asic[48]:768 Asic[49]:768 Asic[50]:768 Asic[51]:768 Asic[52]:768 Asic[53]:768 Asic[54]:768 Asic[55]:768
Asic[56]:768 Asic[57]:768 Asic[58]:768 Asic[59]:768 Asic[60]:768 Asic[61]:768 Asic[62]:768
Chain:5 max freq=768
Chain:5 min freq=768

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=687
Asic[ 0]:781 Asic[ 1]:781 Asic[ 2]:781 Asic[ 3]:781 Asic[ 4]:781 Asic[ 5]:781 Asic[ 6]:781 Asic[ 7]:781
Asic[ 8]:781 Asic[ 9]:781 Asic[10]:781 Asic[11]:781 Asic[12]:781 Asic[13]:781 Asic[14]:781 Asic[15]:781
Asic[16]:781 Asic[17]:781 Asic[18]:781 Asic[19]:781 Asic[20]:781 Asic[21]:781 Asic[22]:781 Asic[23]:781
Asic[24]:781 Asic[25]:781 Asic[26]:781 Asic[27]:781 Asic[28]:781 Asic[29]:781 Asic[30]:781 Asic[31]:781
Asic[32]:781 Asic[33]:781 Asic[34]:781 Asic[35]:781 Asic[36]:781 Asic[37]:781 Asic[38]:781 Asic[39]:781
Asic[40]:781 Asic[41]:781 Asic[42]:781 Asic[43]:781 Asic[44]:781 Asic[45]:781 Asic[46]:781 Asic[47]:781
Asic[48]:781 Asic[49]:781 Asic[50]:781 Asic[51]:781 Asic[52]:781 Asic[53]:781 Asic[54]:781 Asic[55]:781
Asic[56]:781 Asic[57]:781 Asic[58]:781 Asic[59]:781 Asic[60]:781 Asic[61]:781 Asic[62]:781
Chain:6 max freq=781
Chain:6 min freq=781

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=681
Asic[ 0]:775 Asic[ 1]:775 Asic[ 2]:775 Asic[ 3]:775 Asic[ 4]:775 Asic[ 5]:775 Asic[ 6]:775 Asic[ 7]:775
Asic[ 8]:775 Asic[ 9]:775 Asic[10]:775 Asic[11]:775 Asic[12]:775 Asic[13]:775 Asic[14]:775 Asic[15]:775
Asic[16]:775 Asic[17]:775 Asic[18]:775 Asic[19]:775 Asic[20]:775 Asic[21]:775 Asic[22]:775 Asic[23]:775
Asic[24]:775 Asic[25]:775 Asic[26]:775 Asic[27]:775 Asic[28]:775 Asic[29]:775 Asic[30]:775 Asic[31]:775
Asic[32]:775 Asic[33]:775 Asic[34]:775 Asic[35]:775 Asic[36]:775 Asic[37]:775 Asic[38]:775 Asic[39]:775
Asic[40]:775 Asic[41]:775 Asic[42]:775 Asic[43]:775 Asic[44]:775 Asic[45]:775 Asic[46]:775 Asic[47]:775
Asic[48]:775 Asic[49]:775 Asic[50]:775 Asic[51]:775 Asic[52]:775 Asic[53]:775 Asic[54]:775 Asic[55]:775
Asic[56]:775 Asic[57]:775 Asic[58]:775 Asic[59]:775 Asic[60]:775 Asic[61]:775 Asic[62]:775
Chain:7 max freq=775
Chain:7 min freq=775


Miner fix freq ...
totalRate = 16577, fixed_totalRate = 16665
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:768 Asic[ 1]:768 Asic[ 2]:768 Asic[ 3]:768 Asic[ 4]:768 Asic[ 5]:768 Asic[ 6]:768 Asic[ 7]:768
Asic[ 8]:768 Asic[ 9]:768 Asic[10]:768 Asic[11]:768 Asic[12]:768 Asic[13]:768 Asic[14]:768 Asic[15]:768
Asic[16]:768 Asic[17]:768 Asic[18]:768 Asic[19]:768 Asic[20]:768 Asic[21]:768 Asic[22]:768 Asic[23]:768
Asic[24]:768 Asic[25]:768 Asic[26]:768 Asic[27]:768 Asic[28]:768 Asic[29]:768 Asic[30]:768 Asic[31]:768
Asic[32]:768 Asic[33]:768 Asic[34]:768 Asic[35]:768 Asic[36]:768 Asic[37]:768 Asic[38]:768 Asic[39]:768
Asic[40]:768 Asic[41]:768 Asic[42]:768 Asic[43]:768 Asic[44]:768 Asic[45]:768 Asic[46]:768 Asic[47]:768
Asic[48]:768 Asic[49]:768 Asic[50]:768 Asic[51]:768 Asic[52]:768 Asic[53]:768 Asic[54]:768 Asic[55]:768
Asic[56]:768 Asic[57]:768 Asic[58]:768 Asic[59]:768 Asic[60]:768 Asic[61]:768 Asic[62]:768
Chain:5 max freq=768
Chain:5 min freq=768

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=687
Asic[ 0]:781 Asic[ 1]:781 Asic[ 2]:781 Asic[ 3]:781 Asic[ 4]:781 Asic[ 5]:781 Asic[ 6]:781 Asic[ 7]:781
Asic[ 8]:781 Asic[ 9]:781 Asic[10]:781 Asic[11]:781 Asic[12]:781 Asic[13]:781 Asic[14]:781 Asic[15]:781
Asic[16]:781 Asic[17]:781 Asic[18]:781 Asic[19]:781 Asic[20]:781 Asic[21]:781 Asic[22]:781 Asic[23]:781
Asic[24]:781 Asic[25]:781 Asic[26]:781 Asic[27]:781 Asic[28]:781 Asic[29]:781 Asic[30]:781 Asic[31]:781
Asic[32]:781 Asic[33]:781 Asic[34]:781 Asic[35]:781 Asic[36]:781 Asic[37]:781 Asic[38]:781 Asic[39]:781
Asic[40]:781 Asic[41]:781 Asic[42]:781 Asic[43]:781 Asic[44]:781 Asic[45]:781 Asic[46]:781 Asic[47]:781
Asic[48]:781 Asic[49]:781 Asic[50]:781 Asic[51]:781 Asic[52]:781 Asic[53]:781 Asic[54]:781 Asic[55]:781
Asic[56]:781 Asic[57]:781 Asic[58]:781 Asic[59]:781 Asic[60]:781 Asic[61]:781 Asic[62]:781
Chain:6 max freq=781
Chain:6 min freq=781

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=681
Asic[ 0]:775 Asic[ 1]:775 Asic[ 2]:775 Asic[ 3]:775 Asic[ 4]:775 Asic[ 5]:775 Asic[ 6]:775 Asic[ 7]:775
Asic[ 8]:775 Asic[ 9]:775 Asic[10]:775 Asic[11]:775 Asic[12]:775 Asic[13]:775 Asic[14]:775 Asic[15]:775
Asic[16]:775 Asic[17]:775 Asic[18]:775 Asic[19]:775 Asic[20]:775 Asic[21]:775 Asic[22]:775 Asic[23]:775
Asic[24]:775 Asic[25]:775 Asic[26]:775 Asic[27]:775 Asic[28]:775 Asic[29]:775 Asic[30]:775 Asic[31]:775
Asic[32]:775 Asic[33]:775 Asic[34]:775 Asic[35]:775 Asic[36]:775 Asic[37]:775 Asic[38]:775 Asic[39]:775
Asic[40]:775 Asic[41]:775 Asic[42]:775 Asic[43]:775 Asic[44]:775 Asic[45]:775 Asic[46]:775 Asic[47]:775
Asic[48]:775 Asic[49]:775 Asic[50]:775 Asic[51]:775 Asic[52]:775 Asic[53]:775 Asic[54]:775 Asic[55]:775
Asic[56]:775 Asic[57]:775 Asic[58]:775 Asic[59]:775 Asic[60]:775 Asic[61]:775 Asic[62]:775
Chain:7 max freq=775
Chain:7 min freq=775

max freq = 781
totalRate = 16577, fixed_totalRate = 16500
set baud=1
Chain[J6] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=1a
Warning: Chain[5] chip[244] local:26 remote:98 offset:-41, will fixed offset=27
New offset Chain[6] chip[244] local:26 remote:98 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=1a
Chain[J7] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=1a
New offset Chain[7] chip[244] local:25 remote:25 offset:30
Chain[J7] chip[244] get middle temp offset=30 typeID=1a
Chain[J8] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=1a
Warning: Chain[7] chip[244] local:23 remote:101 offset:-48, will fixed offset=27
New offset Chain[8] chip[244] local:23 remote:101 offset:27
Chain[J8] chip[244] get middle temp offset=27 typeID=1a
single board rate=5508 voltage limit=940 on chain[5]
get PIC voltage=870 on chain[5], check: must be < 940
single board rate=5511 voltage limit=940 on chain[6]
get PIC voltage=870 on chain[6], check: must be < 940
single board rate=5557 voltage limit=940 on chain[7]
get PIC voltage=870 on chain[7], check: must be < 940
setting to working voltage...
chain[5] set voltage to 930
chain[6] set voltage to 930
chain[7] set voltage to 930
chain[5] set voltage to 920
chain[6] set voltage to 920
chain[7] set voltage to 920
chain[5] set voltage to 910
chain[6] set voltage to 910
chain[7] set voltage to 910
chain[5] set voltage to 900
chain[6] set voltage to 900
chain[7] set voltage to 900
chain[5] set voltage to 890
chain[6] set voltage to 890
chain[7] set voltage to 890
chain[5] set voltage to 880
chain[6] set voltage to 880
chain[7] set voltage to 880
chain[5] set voltage to 870
chain[6] set voltage to 870
chain[7] set voltage to 870
start thread for read temp
setStartTimePoint total_tv_start_sys=159 total_tv_end_sys=160
restartNum = 2 , auto-reinit enabled...
mining.subscribe:{"id": 0, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer S9j/196500"]}
mining.subscribe:{"id": 1, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer S9j/196500"]}
mining.subscribe:{"id": 10, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer S9j/196500"]}
bring_up_pcb_temp = 49
setting to working voltage...
voltage_check_done
avg hash rate = 16011.067620, ideal hash rate = 16500
hash rate is low...
avg_rate = 16362, ideal_total_hash_rate = 16500
avg_rate = 16416, ideal_total_hash_rate = 16500
avg_rate = 16258, ideal_total_hash_rate = 16500
re_open_core_times: 1
re_open_core enter
Before read Chain[J6] org chain_voltage_pic=125]
After read Chain[J6] new chain_voltage_pic=125 read pic=125
Chain[J6] original vol value=870 adjusted vol value:880
Chain[J6] [org chain_voltage_pic=125 value=870] [new chain_voltage_pic=108 value=880]
Chain[J6] Aisc[00] original freq=762 adjusted freq:768
Chain[J6] Aisc[01] original freq=762 adjusted freq:768
Chain[J6] Aisc[02] original freq=762 adjusted freq:768
Chain[J6] Aisc[03] original freq=762 adjusted freq:768
Chain[J6] Aisc[04] original freq=762 adjusted freq:768
Chain[J6] Aisc[05] original freq=762 adjusted freq:768
Chain[J6] Aisc[06] original freq=762 adjusted freq:768
Chain[J6] Aisc[07] original freq=762 adjusted freq:768
Chain[J6] Aisc[08] original freq=762 adjusted freq:768
Chain[J6] Aisc[09] original freq=762 adjusted freq:768
Chain[J6] Aisc[10] original freq=762 adjusted freq:768
Chain[J6] Aisc[11] original freq=762 adjusted freq:768
Chain[J6] Aisc[12] original freq=762 adjusted freq:768
Chain[J6] Aisc[13] original freq=768 adjusted freq:768
Chain[J6] Aisc[14] original freq=768 adjusted freq:768
Chain[J6] Aisc[15] original freq=768 adjusted freq:768
Chain[J6] Aisc[16] original freq=768 adjusted freq:768
Chain[J6] Aisc[17] original freq=768 adjusted freq:768
Chain[J6] Aisc[18] original freq=768 adjusted freq:768
Chain[J6] Aisc[19] original freq=768 adjusted freq:768
Chain[J6] Aisc[20] original freq=768 adjusted freq:768
Chain[J6] Aisc[21] original freq=768 adjusted freq:768
Chain[J6] Aisc[22] original freq=768 adjusted freq:768
Chain[J6] Aisc[23] original freq=768 adjusted freq:768
Chain[J6] Aisc[24] original freq=768 adjusted freq:768
Chain[J6] Aisc[25] original freq=768 adjusted freq:768
Chain[J6] Aisc[26] original freq=768 adjusted freq:768
Chain[J6] Aisc[27] original freq=768 adjusted freq:768
Chain[J6] Aisc[28] original freq=768 adjusted freq:768
Chain[J6] Aisc[29] original freq=768 adjusted freq:768
Chain[J6] Aisc[30] original freq=768 adjusted freq:768
Chain[J6] Aisc[31] original freq=768 adjusted freq:768
Chain[J6] Aisc[32] original freq=768 adjusted freq:768
Chain[J6] Aisc[33] original freq=768 adjusted freq:768
Chain[J6] Aisc[34] original freq=768 adjusted freq:768
Chain[J6] Aisc[35] original freq=768 adjusted freq:768
Chain[J6] Aisc[36] original freq=768 adjusted freq:768
Chain[J6] Aisc[37] original freq=768 adjusted freq:768
Chain[J6] Aisc[38] original freq=768 adjusted freq:768
Chain[J6] Aisc[39] original freq=768 adjusted freq:768
Chain[J6] Aisc[40] original freq=768 adjusted freq:768
Chain[J6] Aisc[41] original freq=768 adjusted freq:768
Chain[J6] Aisc[42] original freq=768 adjusted freq:768
Chain[J6] Aisc[43] original freq=768 adjusted freq:768
Chain[J6] Aisc[44] original freq=768 adjusted freq:768
Chain[J6] Aisc[45] original freq=768 adjusted freq:768
Chain[J6] Aisc[46] original freq=768 adjusted freq:768
Chain[J6] Aisc[47] original freq=768 adjusted freq:768
Chain[J6] Aisc[48] original freq=768 adjusted freq:768
Chain[J6] Aisc[49] original freq=768 adjusted freq:768
Chain[J6] Aisc[50] original freq=768 adjusted freq:768
Chain[J6] Aisc[51] original freq=768 adjusted freq:768
Chain[J6] Aisc[52] original freq=768 adjusted freq:768
Chain[J6] Aisc[53] original freq=768 adjusted freq:768
Chain[J6] Aisc[54] original freq=768 adjusted freq:768
Chain[J6] Aisc[55] original freq=768 adjusted freq:768
Chain[J6] Aisc[56] original freq=768 adjusted freq:768
Chain[J6] Aisc[57] original freq=768 adjusted freq:768
Chain[J6] Aisc[58] original freq=768 adjusted freq:768
Chain[J6] Aisc[59] original freq=768 adjusted freq:768
Chain[J6] Aisc[60] original freq=768 adjusted freq:768
Chain[J6] Aisc[61] original freq=768 adjusted freq:768
Chain[J6] Aisc[62] original freq=768 adjusted freq:768
Before read Chain[J7] org chain_voltage_pic=125]
After read Chain[J7] new chain_voltage_pic=125 read pic=125
Chain[J7] original vol value=870 adjusted vol value:880
Chain[J7] [org chain_voltage_pic=125 value=870] [new chain_voltage_pic=108 value=880]
Chain[J7] Aisc[00] original freq=775 adjusted freq:781
Chain[J7] Aisc[01] original freq=775 adjusted freq:781
Chain[J7] Aisc[02] original freq=775 adjusted freq:781
Chain[J7] Aisc[03] original freq=775 adjusted freq:781
Chain[J7] Aisc[04] original freq=775 adjusted freq:781
Chain[J7] Aisc[05] original freq=775 adjusted freq:781
Chain[J7] Aisc[06] original freq=775 adjusted freq:781
Chain[J7] Aisc[07] original freq=775 adjusted freq:781
Chain[J7] Aisc[08] original freq=775 adjusted freq:781
Chain[J7] Aisc[09] original freq=775 adjusted freq:781
Chain[J7] Aisc[10] original freq=775 adjusted freq:781
Chain[J7] Aisc[11] original freq=775 adjusted freq:781
Chain[J7] Aisc[12] original freq=775 adjusted freq:781
Chain[J7] Aisc[13] original freq=775 adjusted freq:781
Chain[J7] Aisc[14] original freq=775 adjusted freq:781
Chain[J7] Aisc[15] original freq=775 adjusted freq:781
Chain[J7] Aisc[16] original freq=781 adjusted freq:781
Chain[J7] Aisc[17] original freq=781 adjusted freq:781
Chain[J7] Aisc[18] original freq=781 adjusted freq:781
Chain[J7] Aisc[19] original freq=781 adjusted freq:781
Chain[J7] Aisc[20] original freq=781 adjusted freq:781
Chain[J7] Aisc[21] original freq=781 adjusted freq:781
Chain[J7] Aisc[22] original freq=781 adjusted freq:781
Chain[J7] Aisc[23] original freq=781 adjusted freq:781
Chain[J7] Aisc[24] original freq=781 adjusted freq:781
Chain[J7] Aisc[25] original freq=781 adjusted freq:781
Chain[J7] Aisc[26] original freq=781 adjusted freq:781
Chain[J7] Aisc[27] original freq=781 adjusted freq:781
Chain[J7] Aisc[28] original freq=781 adjusted freq:781
Chain[J7] Aisc[29] original freq=781 adjusted freq:781
Chain[J7] Aisc[30] original freq=781 adjusted freq:781
Chain[J7] Aisc[31] original freq=781 adjusted freq:781
Chain[J7] Aisc[32] original freq=781 adjusted freq:781
Chain[J7] Aisc[33] original freq=781 adjusted freq:781
Chain[J7] Aisc[34] original freq=781 adjusted freq:781
Chain[J7] Aisc[35] original freq=781 adjusted freq:781
Chain[J7] Aisc[36] original freq=781 adjusted freq:781
Chain[J7] Aisc[37] original freq=781 adjusted freq:781
Chain[J7] Aisc[38] original freq=781 adjusted freq:781
Chain[J7] Aisc[39] original freq=781 adjusted freq:781
Chain[J7] Aisc[40] original freq=781 adjusted freq:781
Chain[J7] Aisc[41] original freq=781 adjusted freq:781
Chain[J7] Aisc[42] original freq=781 adjusted freq:781
Chain[J7] Aisc[43] original freq=781 adjusted freq:781
Chain[J7] Aisc[44] original freq=781 adjusted freq:781
Chain[J7] Aisc[45] original freq=781 adjusted freq:781
Chain[J7] Aisc[46] original freq=781 adjusted freq:781
Chain[J7] Aisc[47] original freq=781 adjusted freq:781
Chain[J7] Aisc[48] original freq=781 adjusted freq:781
Chain[J7] Aisc[49] original freq=781 adjusted freq:781
Chain[J7] Aisc[50] original freq=781 adjusted freq:781
Chain[J7] Aisc[51] original freq=781 adjusted freq:781
Chain[J7] Aisc[52] original freq=781 adjusted freq:781
Chain[J7] Aisc[53] original freq=781 adjusted freq:781
Chain[J7] Aisc[54] original freq=781 adjusted freq:781
Chain[J7] Aisc[55] original freq=781 adjusted freq:781
Chain[J7] Aisc[56] original freq=781 adjusted freq:781
Chain[J7] Aisc[57] original freq=781 adjusted freq:781
Chain[J7] Aisc[58] original freq=781 adjusted freq:781
Chain[J7] Aisc[59] original freq=781 adjusted freq:781
Chain[J7] Aisc[60] original freq=781 adjusted freq:781
Chain[J7] Aisc[61] original freq=781 adjusted freq:781
Chain[J7] Aisc[62] original freq=781 adjusted freq:781
Before read Chain[J8] org chain_voltage_pic=125]
After read Chain[J8] new chain_voltage_pic=125 read pic=125
Chain[J8] original vol value=870 adjusted vol value:880
Chain[J8] [org chain_voltage_pic=125 value=870] [new chain_voltage_pic=108 value=880]
Chain[J8] Aisc[00] original freq=762 adjusted freq:775
Chain[J8] Aisc[01] original freq=762 adjusted freq:775
Chain[J8] Aisc[02] original freq=762 adjusted freq:775
Chain[J8] Aisc[03] original freq=762 adjusted freq:775
Chain[J8] Aisc[04] original freq=762 adjusted freq:775
Chain[J8] Aisc[05] original freq=762 adjusted freq:775
Chain[J8] Aisc[06] original freq=762 adjusted freq:775
Chain[J8] Aisc[07] original freq=762 adjusted freq:775
Chain[J8] Aisc[08] original freq=762 adjusted freq:775
Chain[J8] Aisc[09] original freq=762 adjusted freq:775
Chain[J8] Aisc[10] original freq=768 adjusted freq:775
Chain[J8] Aisc[11] original freq=768 adjusted freq:775
Chain[J8] Aisc[12] original freq=768 adjusted freq:775
Chain[J8] Aisc[13] original freq=768 adjusted freq:775
Chain[J8] Aisc[14] original freq=768 adjusted freq:775
Chain[J8] Aisc[15] original freq=768 adjusted freq:775
Chain[J8] Aisc[16] original freq=768 adjusted freq:775
Chain[J8] Aisc[17] original freq=768 adjusted freq:775
Chain[J8] Aisc[18] original freq=768 adjusted freq:775
Chain[J8] Aisc[19] original freq=768 adjusted freq:775
Chain[J8] Aisc[20] original freq=768 adjusted freq:775
Chain[J8] Aisc[21] original freq=768 adjusted freq:775
Chain[J8] Aisc[22] original freq=768 adjusted freq:775
Chain[J8] Aisc[23] original freq=768 adjusted freq:775
Chain[J8] Aisc[24] original freq=768 adjusted freq:775
Chain[J8] Aisc[25] original freq=768 adjusted freq:775
Chain[J8] Aisc[26] original freq=768 adjusted freq:775
Chain[J8] Aisc[27] original freq=768 adjusted freq:775
Chain[J8] Aisc[28] original freq=768 adjusted freq:775
Chain[J8] Aisc[29] original freq=768 adjusted freq:775
Chain[J8] Aisc[30] original freq=768 adjusted freq:775
Chain[J8] Aisc[31] original freq=768 adjusted freq:775
Chain[J8] Aisc[32] original freq=768 adjusted freq:775
Chain[J8] Aisc[33] original freq=768 adjusted freq:775
Chain[J8] Aisc[34] original freq=768 adjusted freq:775
Chain[J8] Aisc[35] original freq=768 adjusted freq:775
Chain[J8] Aisc[36] original freq=768 adjusted freq:775
Chain[J8] Aisc[37] original freq=768 adjusted freq:775
Chain[J8] Aisc[38] original freq=768 adjusted freq:775
Chain[J8] Aisc[39] original freq=768 adjusted freq:775
Chain[J8] Aisc[40] original freq=768 adjusted freq:775
Chain[J8] Aisc[41] original freq=768 adjusted freq:775
Chain[J8] Aisc[42] original freq=768 adjusted freq:775
Chain[J8] Aisc[43] original freq=768 adjusted freq:775
Chain[J8] Aisc[44] original freq=768 adjusted freq:775
Chain[J8] Aisc[45] original freq=768 adjusted freq:775
Chain[J8] Aisc[46] original freq=768 adjusted freq:775
Chain[J8] Aisc[47] original freq=768 adjusted freq:775
Chain[J8] Aisc[48] original freq=768 adjusted freq:775
Chain[J8] Aisc[49] original freq=768 adjusted freq:775
Chain[J8] Aisc[50] original freq=768 adjusted freq:775
Chain[J8] Aisc[51] original freq=768 adjusted freq:775
Chain[J8] Aisc[52] original freq=768 adjusted freq:775
Chain[J8] Aisc[53] original freq=768 adjusted freq:775
Chain[J8] Aisc[54] original freq=768 adjusted freq:775
Chain[J8] Aisc[55] original freq=768 adjusted freq:775
Chain[J8] Aisc[56] original freq=768 adjusted freq:775
Chain[J8] Aisc[57] original freq=768 adjusted freq:775
Chain[J8] Aisc[58] original freq=768 adjusted freq:775
Chain[J8] Aisc[59] original freq=768 adjusted freq:775
Chain[J8] Aisc[60] original freq=768 adjusted freq:775
Chain[J8] Aisc[61] original freq=768 adjusted freq:775
Chain[J8] Aisc[62] original freq=768 adjusted freq:775
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[4] has core num=4
Chain[J6] ASIC[6] has core num=1
Chain[J6] ASIC[10] has core num=2
Chain[J6] ASIC[43] has core num=1
Chain[J6] ASIC[45] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[22] has core num=1
Chain[J7] ASIC[26] has core num=15
Chain[J7] ASIC[42] has core num=1
Chain[J7] ASIC[46] has core num=8
Chain[J7] ASIC[54] has core num=1
Chain[J8] has core num in PIC
Chain[J8] ASIC[17] has core num=8
Chain[J8] ASIC[42] has core num=3
miner total rate=16577GH/s ideal_total_hash_rate = 16500GH/s
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:768 Asic[ 1]:768 Asic[ 2]:768 Asic[ 3]:768 Asic[ 4]:768 Asic[ 5]:768 Asic[ 6]:768 Asic[ 7]:768
Asic[ 8]:768 Asic[ 9]:768 Asic[10]:768 Asic[11]:768 Asic[12]:768 Asic[13]:768 Asic[14]:768 Asic[15]:768
Asic[16]:768 Asic[17]:768 Asic[18]:768 Asic[19]:768 Asic[20]:768 Asic[21]:768 Asic[22]:768 Asic[23]:768
Asic[24]:768 Asic[25]:768 Asic[26]:768 Asic[27]:768 Asic[28]:768 Asic[29]:768 Asic[30]:768 Asic[31]:768
Asic[32]:768 Asic[33]:768 Asic[34]:768 Asic[35]:768 Asic[36]:768 Asic[37]:768 Asic[38]:768 Asic[39]:768
Asic[40]:768 Asic[41]:768 Asic[42]:768 Asic[43]:768 Asic[44]:768 Asic[45]:768 Asic[46]:768 Asic[47]:768
Asic[48]:768 Asic[49]:768 Asic[50]:768 Asic[51]:768 Asic[52]:768 Asic[53]:768 Asic[54]:768 Asic[55]:768
Asic[56]:768 Asic[57]:768 Asic[58]:768 Asic[59]:768 Asic[60]:768 Asic[61]:768 Asic[62]:768
Chain:5 max freq=768
Chain:5 min freq=768

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=687
Asic[ 0]:781 Asic[ 1]:781 Asic[ 2]:781 Asic[ 3]:781 Asic[ 4]:781 Asic[ 5]:781 Asic[ 6]:781 Asic[ 7]:781
Asic[ 8]:781 Asic[ 9]:781 Asic[10]:781 Asic[11]:781 Asic[12]:781 Asic[13]:781 Asic[14]:781 Asic[15]:781
Asic[16]:781 Asic[17]:781 Asic[18]:781 Asic[19]:781 Asic[20]:781 Asic[21]:781 Asic[22]:781 Asic[23]:781
Asic[24]:781 Asic[25]:781 Asic[26]:781 Asic[27]:781 Asic[28]:781 Asic[29]:781 Asic[30]:781 Asic[31]:781
Asic[32]:781 Asic[33]:781 Asic[34]:781 Asic[35]:781 Asic[36]:781 Asic[37]:781 Asic[38]:781 Asic[39]:781
Asic[40]:781 Asic[41]:781 Asic[42]:781 Asic[43]:781 Asic[44]:781 Asic[45]:781 Asic[46]:781 Asic[47]:781
Asic[48]:781 Asic[49]:781 Asic[50]:781 Asic[51]:781 Asic[52]:781 Asic[53]:781 Asic[54]:781 Asic[55]:781
Asic[56]:781 Asic[57]:781 Asic[58]:781 Asic[59]:781 Asic[60]:781 Asic[61]:781 Asic[62]:781
Chain:6 max freq=781
Chain:6 min freq=781

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=681
Asic[ 0]:775 Asic[ 1]:775 Asic[ 2]:775 Asic[ 3]:775 Asic[ 4]:775 Asic[ 5]:775 Asic[ 6]:775 Asic[ 7]:775
Asic[ 8]:775 Asic[ 9]:775 Asic[10]:775 Asic[11]:775 Asic[12]:775 Asic[13]:775 Asic[14]:775 Asic[15]:775
Asic[16]:775 Asic[17]:775 Asic[18]:775 Asic[19]:775 Asic[20]:775 Asic[21]:775 Asic[22]:775 Asic[23]:775
Asic[24]:775 Asic[25]:775 Asic[26]:775 Asic[27]:775 Asic[28]:775 Asic[29]:775 Asic[30]:775 Asic[31]:775
Asic[32]:775 Asic[33]:775 Asic[34]:775 Asic[35]:775 Asic[36]:775 Asic[37]:775 Asic[38]:775 Asic[39]:775
Asic[40]:775 Asic[41]:775 Asic[42]:775 Asic[43]:775 Asic[44]:775 Asic[45]:775 Asic[46]:775 Asic[47]:775
Asic[48]:775 Asic[49]:775 Asic[50]:775 Asic[51]:775 Asic[52]:775 Asic[53]:775 Asic[54]:775 Asic[55]:775
Asic[56]:775 Asic[57]:775 Asic[58]:775 Asic[59]:775 Asic[60]:775 Asic[61]:775 Asic[62]:775
Chain:7 max freq=775
Chain:7 min freq=775


Miner fix freq ...
totalRate = 16577, fixed_totalRate = 16665
read PIC voltage=940 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
Chain:5 temp offset=0
Chain:5 base freq=675
Asic[ 0]:768 Asic[ 1]:768 Asic[ 2]:768 Asic[ 3]:768 Asic[ 4]:768 Asic[ 5]:768 Asic[ 6]:768 Asic[ 7]:768
Asic[ 8]:768 Asic[ 9]:768 Asic[10]:768 Asic[11]:768 Asic[12]:768 Asic[13]:768 Asic[14]:768 Asic[15]:768
Asic[16]:768 Asic[17]:768 Asic[18]:768 Asic[19]:768 Asic[20]:768 Asic[21]:768 Asic[22]:768 Asic[23]:768
Asic[24]:768 Asic[25]:768 Asic[26]:768 Asic[27]:768 Asic[28]:768 Asic[29]:768 Asic[30]:768 Asic[31]:768
Asic[32]:768 Asic[33]:768 Asic[34]:768 Asic[35]:768 Asic[36]:768 Asic[37]:768 Asic[38]:768 Asic[39]:768
Asic[40]:768 Asic[41]:768 Asic[42]:768 Asic[43]:768 Asic[44]:768 Asic[45]:768 Asic[46]:768 Asic[47]:768
Asic[48]:768 Asic[49]:768 Asic[50]:768 Asic[51]:768 Asic[52]:768 Asic[53]:768 Asic[54]:768 Asic[55]:768
Asic[56]:768 Asic[57]:768 Asic[58]:768 Asic[59]:768 Asic[60]:768 Asic[61]:768 Asic[62]:768
Chain:5 max freq=768
Chain:5 min freq=768

read PIC voltage=940 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
Chain:6 temp offset=0
Chain:6 base freq=687
Asic[ 0]:781 Asic[ 1]:781 Asic[ 2]:781 Asic[ 3]:781 Asic[ 4]:781 Asic[ 5]:781 Asic[ 6]:781 Asic[ 7]:781
Asic[ 8]:781 Asic[ 9]:781 Asic[10]:781 Asic[11]:781 Asic[12]:781 Asic[13]:781 Asic[14]:781 Asic[15]:781
Asic[16]:781 Asic[17]:781 Asic[18]:781 Asic[19]:781 Asic[20]:781 Asic[21]:781 Asic[22]:781 Asic[23]:781
Asic[24]:781 Asic[25]:781 Asic[26]:781 Asic[27]:781 Asic[28]:781 Asic[29]:781 Asic[30]:781 Asic[31]:781
Asic[32]:781 Asic[33]:781 Asic[34]:781 Asic[35]:781 Asic[36]:781 Asic[37]:781 Asic[38]:781 Asic[39]:781
Asic[40]:781 Asic[41]:781 Asic[42]:781 Asic[43]:781 Asic[44]:781 Asic[45]:781 Asic[46]:781 Asic[47]:781
Asic[48]:781 Asic[49]:781 Asic[50]:781 Asic[51]:781 Asic[52]:781 Asic[53]:781 Asic[54]:781 Asic[55]:781
Asic[56]:781 Asic[57]:781 Asic[58]:781 Asic[59]:781 Asic[60]:781 Asic[61]:781 Asic[62]:781
Chain:6 max freq=781
Chain:6 min freq=781

read PIC voltage=940 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.0V
Chain:7 temp offset=0
Chain:7 base freq=681
Asic[ 0]:775 Asic[ 1]:775 Asic[ 2]:775 Asic[ 3]:775 Asic[ 4]:775 Asic[ 5]:775 Asic[ 6]:775 Asic[ 7]:775
Asic[ 8]:775 Asic[ 9]:775 Asic[10]:775 Asic[11]:775 Asic[12]:775 Asic[13]:775 Asic[14]:775 Asic[15]:775
Asic[16]:775 Asic[17]:775 Asic[18]:775 Asic[19]:775 Asic[20]:775 Asic[21]:775 Asic[22]:775 Asic[23]:775
Asic[24]:775 Asic[25]:775 Asic[26]:775 Asic[27]:775 Asic[28]:775 Asic[29]:775 Asic[30]:775 Asic[31]:775
Asic[32]:775 Asic[33]:775 Asic[34]:775 Asic[35]:775 Asic[36]:775 Asic[37]:775 Asic[38]:775 Asic[39]:775
Asic[40]:775 Asic[41]:775 Asic[42]:775 Asic[43]:775 Asic[44]:775 Asic[45]:775 Asic[46]:775 Asic[47]:775
Asic[48]:775 Asic[49]:775 Asic[50]:775 Asic[51]:775 Asic[52]:775 Asic[53]:775 Asic[54]:775 Asic[55]:775
Asic[56]:775 Asic[57]:775 Asic[58]:775 Asic[59]:775 Asic[60]:775 Asic[61]:775 Asic[62]:775
Chain:7 max freq=775
Chain:7 min freq=775

max freq = 781
totalRate = 16577, fixed_totalRate = 16500
set baud=1
Chain[J6] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
Chain[J6] chip[244] use PIC middle temp offset=0 typeID=1a
Warning: Chain[5] chip[244] local:45 remote:114 offset:-36, will fixed offset=27
New offset Chain[6] chip[244] local:45 remote:114 offset:27
Chain[J6] chip[244] get middle temp offset=27 typeID=1a
Chain[J7] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
Chain[J7] chip[244] use PIC middle temp offset=0 typeID=1a
Warning: Chain[6] chip[244] local:39 remote:119 offset:-48, will fixed offset=27
New offset Chain[7] chip[244] local:39 remote:119 offset:27
Chain[J7] chip[244] get middle temp offset=27 typeID=1a
Chain[J8] PIC temp offset: 62,0,0,0,0,0,35,28,0,0,0,0,0,0,0,0,0,0,
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J8] chip[244] use PIC middle temp offset=0 typeID=1a
Warning: Chain[7] chip[244] local:36 remote:112 offset:-44, will fixed offset=27
New offset Chain[8] chip[244] local:36 remote:112 offset:27
Chain[J8] chip[244] get middle temp offset=27 typeID=1a
setting to working voltage...
chain[5] set voltage to 930
chain[6] set voltage to 930
chain[7] set voltage to 930
chain[5] set voltage to 920
chain[6] set voltage to 920
chain[7] set voltage to 920
chain[5] set voltage to 910
chain[6] set voltage to 910
chain[7] set voltage to 910
chain[5] set voltage to 900
chain[6] set voltage to 900
chain[7] set voltage to 900
chain[5] set voltage to 890
chain[6] set voltage to 890
chain[7] set voltage to 890
chain[5] set voltage to 880
chain[6] set voltage to 880
chain[7] set voltage to 880
reopen core end
avg_rate = 16162, ideal_total_hash_rate = 16500
avg_rate = 16605, ideal_total_hash_rate = 16500
avg hash rate is OK
avg_rate = 16528, ideal_total_hash_rate = 16500
avg hash rate is OK
avg_rate = 16548, ideal_total_hash_rate = 16500
avg hash rate is OK
do read_temp_func once...

get RT hashrate from Chain[5]: (asic index start from 1-63)
Asic[01]=86.3180 Asic[02]=87.9120 Asic[03]=86.7880 Asic[04]=84.4060 Asic[05]=86.2510 Asic[06]=91.6030 Asic[07]=91.9050 Asic[08]=87.5260
Asic[09]=91.5020 Asic[10]=85.7810 Asic[11]=88.1300 Asic[12]=88.6500 Asic[13]=91.1670 Asic[14]=83.7180 Asic[15]=87.7280 Asic[16]=80.5300
Asic[17]=85.9830 Asic[18]=91.8380 Asic[19]=83.9360 Asic[20]=87.1400 Asic[21]=86.0160 Asic[22]=85.8150 Asic[23]=88.8850 Asic[24]=84.5570
Asic[25]=92.4760 Asic[26]=92.5260 Asic[27]=96.2170 Asic[28]=84.3550 Asic[29]=84.8920 Asic[30]=86.3180 Asic[31]=86.1000 Asic[32]=91.3510
Asic[33]=90.5290 Asic[34]=84.5400 Asic[35]=88.3650 Asic[36]=89.2210 Asic[37]=86.5200 Asic[38]=91.6030 Asic[39]=87.6940 Asic[40]=83.0800
Asic[41]=88.0300 Asic[42]=84.6240 Asic[43]=90.7140 Asic[44]=87.8950 Asic[45]=84.7410 Asic[46]=90.7980 Asic[47]=89.1370 Asic[48]=86.0330
Asic[49]=87.3250 Asic[50]=85.0770 Asic[51]=83.4830 Asic[52]=87.0400 Asic[53]=86.6200 Asic[54]=35213.6 Asic[55]=85.1440 Asic[56]=90.3280
Asic[57]=90.3780 Asic[58]=92.9280 Asic[59]=89.1540 Asic[60]=66.3530 Asic[61]=89.7910 Asic[62]=81.0500 Asic[63]=88.1300

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=92.6270 Asic[02]=88.1470 Asic[03]=97.4250 Asic[04]=87.8450 Asic[05]=82.7950 Asic[06]=90.9320 Asic[07]=84.7410 Asic[08]=87.0230
Asic[09]=90.3110 Asic[10]=83.3150 Asic[11]=87.5600 Asic[12]=86.4520 Asic[13]=85.7140 Asic[14]=90.9820 Asic[15]=88.4490 Asic[16]=88.5330
Asic[17]=90.6970 Asic[18]=80.0940 Asic[19]=88.3320 Asic[20]=85.7980 Asic[21]=85.1270 Asic[22]=84.5400 Asic[23]=78.3990 Asic[24]=90.1600
Asic[25]=92.3920 Asic[26]=91.3510 Asic[27]=22.4140 Asic[28]=85.0430 Asic[29]=88.8520 Asic[30]=90.6470 Asic[31]=88.7170 Asic[32]=87.2750
Asic[33]=93.3310 Asic[34]=84.1040 Asic[35]=90.2110 Asic[36]=88.0970 Asic[37]=87.8280 Asic[38]=85.6640 Asic[39]=90.8310 Asic[40]=87.5430
Asic[41]=85.7650 Asic[42]=91.3010 Asic[43]=90.5290 Asic[44]=89.4390 Asic[45]=92.1900 Asic[46]=88.8850 Asic[47]=80.0270 Asic[48]=91.3850
Asic[49]=84.3220 Asic[50]=96.3510 Asic[51]=87.4930 Asic[52]=89.9920 Asic[53]=87.2410 Asic[54]=89.2380 Asic[55]=86.3520 Asic[56]=84.4560
Asic[57]=89.7240 Asic[58]=92.4760 Asic[59]=87.7780 Asic[60]=88.9360 Asic[61]=86.6710 Asic[62]=91.8040 Asic[63]=87.4760

get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=88.9190 Asic[02]=90.4290 Asic[03]=87.7780 Asic[04]=84.0530 Asic[05]=90.2610 Asic[06]=83.3820 Asic[07]=88.1810 Asic[08]=90.7640
Asic[09]=90.2940 Asic[10]=89.1370 Asic[11]=86.5200 Asic[12]=89.3550 Asic[13]=84.6740 Asic[14]=89.2710 Asic[15]=84.4560 Asic[16]=86.5360
Asic[17]=90.3620 Asic[18]=85.3790 Asic[19]=87.0230 Asic[20]=87.0900 Asic[21]=86.1170 Asic[22]=89.6900 Asic[23]=84.4560 Asic[24]=85.2780
Asic[25]=84.0200 Asic[26]=90.4120 Asic[27]=90.5130 Asic[28]=88.8350 Asic[29]=88.3820 Asic[30]=87.5930 Asic[31]=87.1240 Asic[32]=89.1030
Asic[33]=91.5360 Asic[34]=87.1910 Asic[35]=88.2140 Asic[36]=84.3720 Asic[37]=84.6410 Asic[38]=86.8220 Asic[39]=95.5290 Asic[40]=85.0100
Asic[41]=85.4120 Asic[42]=90.3620 Asic[43]=86.4690 Asic[44]=85.5300 Asic[45]=81.8890 Asic[46]=82.0740 Asic[47]=93.6000 Asic[48]=83.6670
Asic[49]=83.3150 Asic[50]=86.9560 Asic[51]=88.5160 Asic[52]=90.7640 Asic[53]=84.7750 Asic[54]=82.2080 Asic[55]=90.9990 Asic[56]=85.1610
Asic[57]=88.0800 Asic[58]=84.1880 Asic[59]=90.3950 Asic[60]=82.9630 Asic[61]=90.5130 Asic[62]=87.7440 Asic[63]=85.2610
Check Chain[J6] ASIC RT error: (asic index start from 1-63)
Asic[54]=35213.600000
Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Done check_asic_reg
Chain[5] Chip[244] pcb temperature=60
Chain[5] Chip[62] junction temperature=142
Special fix Chain[5] Chip[62] middle Temp = 75
Done read temp on Chain[5]
Chain[6] Chip[244] pcb temperature=56
read failed on Chain[6] Chip[62] middle Temp old value:70
Special fix Chain[6] Chip[62] middle Temp = 71
Done read temp on Chain[6]
Chain[7] Chip[244] pcb temperature=57
read failed on Chain[7] Chip[62] middle Temp old value:73
Special fix Chain[7] Chip[62] middle Temp = 72
Done read temp on Chain[7]
Max pcb temp : 60
set FAN speed according to: temp_highest=60 temp_top1[PWM_T]=60 temp_top1[TEMP_POS_LOCAL]=60 temp_change=1 fix_fan_steps=0
FAN PWM: 68
read_temp_func Done!
CRC error counter=106

Bitcoin Forum>Bitcoin>Mining>Mining support
Jump to: