Bitcoin Forum>Bitcoin>Mining>Mining support
Author

Topic: Antminer T9+ Low Hashrate on chains (Read 383 times)

eddie4wd
newbie
Activity: 4
Merit: 0
Antminer T9+ Low Hashrate on chains
May 01, 2020, 04:56:28 PM
#8
can you help me ? please .... i have a problem with my antminer T9 + it restarts every 3 minutes

Code:
driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[2]
driver-btm-c5.c:4610:set_frequency: Chain:2 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J3] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:2 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:2 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:2 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[3]
driver-btm-c5.c:4610:set_frequency: Chain:3 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J4] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:3 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:3 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:3 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[8]
driver-btm-c5.c:4610:set_frequency: Chain:8 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J9] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:8 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:8 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:8 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[9]
driver-btm-c5.c:4610:set_frequency: Chain:9 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J10] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:9 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:9 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:9 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[10]
driver-btm-c5.c:4610:set_frequency: Chain:10 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J11] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:10 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:10 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:10 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[11]
driver-btm-c5.c:4610:set_frequency: Chain:11 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J12] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:11 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:11 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:11 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[12]
driver-btm-c5.c:4610:set_frequency: Chain:12 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J13] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:12 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:12 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:12 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[13]
driver-btm-c5.c:4610:set_frequency: Chain:13 chipnum=1
driver-btm-c5.c:4620:set_frequency: Chain[J14] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:13 base freq=575
Asic[ 0]:575
driver-btm-c5.c:4821:set_frequency: Chain:13 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:13 min freq=575


driver-btm-c5.c:4831:set_frequency: Miner fix freq ...
driver-btm-c5.c:4250:ProcessFixFreqForChips: totalRate = 10619, fixed_totalRate = 10710
driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[1]
driver-btm-c5.c:4867:set_frequency: Chain:1 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J2] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:1 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:1 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:1 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[2]
driver-btm-c5.c:4867:set_frequency: Chain:2 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J3] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:2 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:2 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:2 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[3]
driver-btm-c5.c:4867:set_frequency: Chain:3 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J4] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:3 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:3 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:3 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[8]
driver-btm-c5.c:4867:set_frequency: Chain:8 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J9] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:8 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:8 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:8 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[9]
driver-btm-c5.c:4867:set_frequency: Chain:9 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J10] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:9 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:9 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:9 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[10]
driver-btm-c5.c:4867:set_frequency: Chain:10 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J11] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:10 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:10 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:10 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[11]
driver-btm-c5.c:4867:set_frequency: Chain:11 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J12] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:11 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:11 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:11 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[12]
driver-btm-c5.c:4867:set_frequency: Chain:12 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J13] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:12 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:12 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:12 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[13]
driver-btm-c5.c:4867:set_frequency: Chain:13 chipnum=1
driver-btm-c5.c:4876:set_frequency: Chain[J14] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:13 base freq=575
Asic[ 0]:575
driver-btm-c5.c:5122:set_frequency: Chain:13 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:13 min freq=575

driver-btm-c5.c:5131:set_frequency: max freq = 575
driver-btm-c5.c:4149:ProcessFixFreq: totalRate = 10619, fixed_totalRate = 10500
driver-btm-c5.c:9614:init_uart_baud: set baud=1
driver-btm-c5.c:6605:calibration_sensor_offset: Chain[J9] PIC temp offset: 1,-5,0,0,0,0,33,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6639:calibration_sensor_offset: chain[9] temp chip I2C addr=0x98
driver-btm-c5.c:6672:calibration_sensor_offset: Chain[J9] chip[0] use PIC middle temp offset=-5 typeID=00
driver-btm-c5.c:6777:calibration_sensor_offset: Warning: Chain[J9] has no temp offset in PIC! will fix it
driver-btm-c5.c:6901:calibration_sensor_offset: Chain[J9] use default temp chip[0]
driver-btm-c5.c:6331:do_calibration_sensor_offset: Chain[J9] try read temp chip[0] ID=00 (I2C addr=0x98)
driver-btm-c5.c:6343:do_calibration_sensor_offset: Chain[J9] try read temp chip[0] ID=00 (I2C addr=0x9A)
driver-btm-c5.c:6355:do_calibration_sensor_offset: Chain[J9] try read temp chip[0] ID=00 (I2C addr=0x9C)
driver-btm-c5.c:6396:do_calibration_sensor_offset: New offset Chain[9] chip[0] local:-64 remote:-64 offset:21
driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J9] chip[0] get middle temp offset=21 typeID=00
driver-btm-c5.c:6605:calibration_sensor_offset: Chain[J11] PIC temp offset: 1,-3,0,0,0,0,33,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6639:calibration_sensor_offset: chain[11] temp chip I2C addr=0x98
driver-btm-c5.c:6672:calibration_sensor_offset: Chain[J11] chip[0] use PIC middle temp offset=-3 typeID=55
driver-btm-c5.c:6396:do_calibration_sensor_offset: New offset Chain[11] chip[0] local:31 remote:33 offset:28
driver-btm-c5.c:6765:calibration_sensor_offset: Chain[J11] chip[0] get middle temp offset=28 typeID=55
driver-btm-c5.c:6605:calibration_sensor_offset: Chain[J13] PIC temp offset: 1,-4,0,0,0,0,33,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6639:calibration_sensor_offset: chain[13] temp chip I2C addr=0x98
driver-btm-c5.c:6672:calibration_sensor_offset: Chain[J13] chip[0] use PIC middle temp offset=-4 typeID=00
driver-btm-c5.c:6777:calibration_sensor_offset: Warning: Chain[J13] has no temp offset in PIC! will fix it
driver-btm-c5.c:6901:calibration_sensor_offset: Chain[J13] use default temp chip[0]
driver-btm-c5.c:6331:do_calibration_sensor_offset: Chain[J13] try read temp chip[0] ID=00 (I2C addr=0x98)
driver-btm-c5.c:6343:do_calibration_sensor_offset: Chain[J13] try read temp chip[0] ID=00 (I2C addr=0x9A)
driver-btm-c5.c:6355:do_calibration_sensor_offset: Chain[J13] try read temp chip[0] ID=00 (I2C addr=0x9C)
driver-btm-c5.c:6396:do_calibration_sensor_offset: New offset Chain[13] chip[0] local:-64 remote:-64 offset:21
driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J13] chip[0] get middle temp offset=21 typeID=00
driver-btm-c5.c:13824:bitmain_c5_init: open core three times
driver-btm-c5.c:13851:bitmain_c5_init: open core on chain[1] [8] [9]...
driver-btm-c5.c:13824:bitmain_c5_init: open core three times
driver-btm-c5.c:13868:bitmain_c5_init: open core on chain[2] [10] [11]...
driver-btm-c5.c:13824:bitmain_c5_init: open core three times
driver-btm-c5.c:13884:bitmain_c5_init: open core on chain[3] [12] [13]...
driver-btm-c5.c:13824:bitmain_c5_init: open core three times
driver-btm-c5.c:12129:set_working_voltage: setting to working voltage...
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 9 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[1] set voltage to 880
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 9 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[2] set voltage to 880
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 9 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[3] set voltage to 880
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 11 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[1] set voltage to 870
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 11 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[2] set voltage to 870
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 11 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[3] set voltage to 870
driver-btm-c5.c:14027:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=257 total_tv_end_sys=258
driver-btm-c5.c:10330:check_system_work: restartNum = 2 , auto-reinit enabled...
util.c:3207:initiate_stratum: mining.subscribe:{"id": 0, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer T9+/10500"]}
util.c:3207:initiate_stratum: mining.subscribe:{"id": 1, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer T9+/10500"]}
driver-btm-c5.c:8738:read_temp_func: bring_up_pcb_temp = 55
util.c:3207:initiate_stratum: mining.subscribe:{"id": 8, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer T9+/10500"]}
driver-btm-c5.c:10461:check_system_work: checking hash again
driver-btm-c5.c:9897:if_avg_hash_ok: avg hash rate = 9490.836893, ideal hash rate = 10500
driver-btm-c5.c:10389:check_system_work: re_open_core_times: 1
driver-btm-c5.c:15703:re_open_core: re_open_core enter
driver-btm-c5.c:15802:re_open_core: Before read Chain[J2] org chain_voltage_pic=11]
driver-btm-c5.c:15808:re_open_core: After read Chain[J2] new chain_voltage_pic=11 read pic=11
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 7 seccessful
driver-btm-c5.c:15802:re_open_core: Before read Chain[J3] org chain_voltage_pic=11]
driver-btm-c5.c:15808:re_open_core: After read Chain[J3] new chain_voltage_pic=11 read pic=11
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 7 seccessful
driver-btm-c5.c:15802:re_open_core: Before read Chain[J4] org chain_voltage_pic=11]
driver-btm-c5.c:15808:re_open_core: After read Chain[J4] new chain_voltage_pic=11 read pic=11
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 7 seccessful
driver-btm-c5.c:15802:re_open_core: Before read Chain[J9] org chain_voltage_pic=11]
driver-btm-c5.c:15808:re_open_core: After read Chain[J9] new chain_voltage_pic=7 read pic=7
driver-btm-c5.c:15802:re_open_core: Before read Chain[J10] org chain_voltage_pic=11]
driver-btm-c5.c:15808:re_open_core: After read Chain[J10] new chain_voltage_pic=7 read pic=7
driver-btm-c5.c:15802:re_open_core: Before read Chain[J11] org chain_voltage_pic=11]
driver-btm-c5.c:15808:re_open_core: After read Chain[J11] new chain_voltage_pic=7 read pic=7
driver-btm-c5.c:15802:re_open_core: Before read Chain[J12] org chain_voltage_pic=11]
driver-btm-c5.c:15808:re_open_core: After read Chain[J12] new chain_voltage_pic=7 read pic=7
driver-btm-c5.c:15802:re_open_core: Before read Chain[J13] org chain_voltage_pic=11]
driver-btm-c5.c:15808:re_open_core: After read Chain[J13] new chain_voltage_pic=7 read pic=7
driver-btm-c5.c:15802:re_open_core: Before read Chain[J14] org chain_voltage_pic=11]
driver-btm-c5.c:15808:re_open_core: After read Chain[J14] new chain_voltage_pic=7 read pic=7
driver-btm-c5.c:9785:pic_heart_beat_func: chain[1] heart beat fail 1 times.
driver-btm-c5.c:11856:T9_18_getASICnum: T9+ try get asic num for the 1 time
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J2] has 18 asic
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J3] has 18 asic
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J4] has 18 asic
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J9] has 18 asic
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J10] has 18 asic
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J11] has 18 asic
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J12] has 18 asic
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J13] has 18 asic
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J14] has 18 asic
driver-btm-c5.c:4486:set_frequency: Chain[J2] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J3] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J4] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J9] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J10] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J11] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J12] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J13] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J14] has core num in PIC
driver-btm-c5.c:4583:set_frequency: miner total rate=10619GH/s ideal_total_hash_rate = 10500GH/s
driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[1]
driver-btm-c5.c:4610:set_frequency: Chain:1 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J2] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:1 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:1 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:1 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[2]
driver-btm-c5.c:4610:set_frequency: Chain:2 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J3] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:2 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:2 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:2 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[3]
driver-btm-c5.c:4610:set_frequency: Chain:3 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J4] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:3 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:3 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:3 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[8]
driver-btm-c5.c:4610:set_frequency: Chain:8 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J9] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:8 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:8 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:8 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[9]
driver-btm-c5.c:4610:set_frequency: Chain:9 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J10] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:9 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:9 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:9 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[10]
driver-btm-c5.c:4610:set_frequency: Chain:10 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J11] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:10 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:10 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:10 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[11]
driver-btm-c5.c:4610:set_frequency: Chain:11 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J12] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:11 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:11 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:11 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[12]
driver-btm-c5.c:4610:set_frequency: Chain:12 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J13] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:12 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:12 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:12 min freq=575

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[13]
driver-btm-c5.c:4610:set_frequency: Chain:13 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J14] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:13 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:4821:set_frequency: Chain:13 max freq=575
driver-btm-c5.c:4822:set_frequency: Chain:13 min freq=575


driver-btm-c5.c:4831:set_frequency: Miner fix freq ...
driver-btm-c5.c:4250:ProcessFixFreqForChips: totalRate = 10619, fixed_totalRate = 10710
driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[1]
driver-btm-c5.c:4867:set_frequency: Chain:1 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J2] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:1 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:1 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:1 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[2]
driver-btm-c5.c:4867:set_frequency: Chain:2 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J3] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:2 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:2 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:2 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[3]
driver-btm-c5.c:4867:set_frequency: Chain:3 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J4] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:3 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:3 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:3 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[8]
driver-btm-c5.c:4867:set_frequency: Chain:8 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J9] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:8 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:8 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:8 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[9]
driver-btm-c5.c:4867:set_frequency: Chain:9 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J10] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:9 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:9 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:9 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[10]
driver-btm-c5.c:4867:set_frequency: Chain:10 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J11] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:10 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:10 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:10 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[11]
driver-btm-c5.c:4867:set_frequency: Chain:11 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J12] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:11 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:11 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:11 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[12]
driver-btm-c5.c:4867:set_frequency: Chain:12 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J13] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:12 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:12 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:12 min freq=575

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[13]
driver-btm-c5.c:4867:set_frequency: Chain:13 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J14] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:13 base freq=575
Asic[ 0]:575 Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575
Asic[ 8]:575 Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575
Asic[16]:575 Asic[17]:575
driver-btm-c5.c:5122:set_frequency: Chain:13 max freq=575
driver-btm-c5.c:5123:set_frequency: Chain:13 min freq=575

driver-btm-c5.c:5131:set_frequency: max freq = 575
driver-btm-c5.c:4149:ProcessFixFreq: totalRate = 10619, fixed_totalRate = 10500
driver-btm-c5.c:9614:init_uart_baud: set baud=1
driver-btm-c5.c:6605:calibration_sensor_offset: Chain[J9] PIC temp offset: 1,-5,0,0,0,0,33,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6639:calibration_sensor_offset: chain[9] temp chip I2C addr=0x98
driver-btm-c5.c:6672:calibration_sensor_offset: Chain[J9] chip[0] use PIC middle temp offset=-5 typeID=00
driver-btm-c5.c:6777:calibration_sensor_offset: Warning: Chain[J9] has no temp offset in PIC! will fix it
driver-btm-c5.c:6901:calibration_sensor_offset: Chain[J9] use default temp chip[0]
driver-btm-c5.c:6331:do_calibration_sensor_offset: Chain[J9] try read temp chip[0] ID=00 (I2C addr=0x98)
driver-btm-c5.c:6343:do_calibration_sensor_offset: Chain[J9] try read temp chip[0] ID=00 (I2C addr=0x9A)
driver-btm-c5.c:6355:do_calibration_sensor_offset: Chain[J9] try read temp chip[0] ID=00 (I2C addr=0x9C)
driver-btm-c5.c:6396:do_calibration_sensor_offset: New offset Chain[9] chip[0] local:-64 remote:-64 offset:21
driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J9] chip[0] get middle temp offset=21 typeID=00
driver-btm-c5.c:6605:calibration_sensor_offset: Chain[J11] PIC temp offset: 1,-3,0,0,0,0,33,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6639:calibration_sensor_offset: chain[11] temp chip I2C addr=0x98
driver-btm-c5.c:6672:calibration_sensor_offset: Chain[J11] chip[0] use PIC middle temp offset=-3 typeID=55
driver-btm-c5.c:6396:do_calibration_sensor_offset: New offset Chain[11] chip[0] local:42 remote:43 offset:30
driver-btm-c5.c:6765:calibration_sensor_offset: Chain[J11] chip[0] get middle temp offset=30 typeID=55
driver-btm-c5.c:6605:calibration_sensor_offset: Chain[J13] PIC temp offset: 1,-4,0,0,0,0,33,28,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6639:calibration_sensor_offset: chain[13] temp chip I2C addr=0x98
driver-btm-c5.c:6672:calibration_sensor_offset: Chain[J13] chip[0] use PIC middle temp offset=-4 typeID=00
driver-btm-c5.c:6777:calibration_sensor_offset: Warning: Chain[J13] has no temp offset in PIC! will fix it
driver-btm-c5.c:6901:calibration_sensor_offset: Chain[J13] use default temp chip[0]
driver-btm-c5.c:6331:do_calibration_sensor_offset: Chain[J13] try read temp chip[0] ID=55 (I2C addr=0x98)
driver-btm-c5.c:6396:do_calibration_sensor_offset: New offset Chain[13] chip[0] local:38 remote:40 offset:29
driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J13] chip[0] get middle temp offset=29 typeID=55
driver-btm-c5.c:16050:re_open_core: open core on chain[1] [8] [9]...
driver-btm-c5.c:16067:re_open_core: open core on chain[2] [10] [11]...
driver-btm-c5.c:16083:re_open_core: open core on chain[3] [12] [13]...
driver-btm-c5.c:12129:set_working_voltage: setting to working voltage...
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 9 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[1] set voltage to 880
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 9 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[2] set voltage to 880
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 9 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[3] set voltage to 880
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 11 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[1] set voltage to 870
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 11 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[2] set voltage to 870
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 11 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[3] set voltage to 870
driver-btm-c5.c:16177:re_open_core: reopen core end
driver-btm-c5.c:10461:check_system_work: checking hash again
driver-btm-c5.c:9897:if_avg_hash_ok: avg hash rate = 8989.857025, ideal hash rate = 10500
do read_temp_func once...

get RT hashrate from Chain[1]: (asic index start from 1-18)
Asic[01]=64.2230 Asic[02]=65.0950 Asic[03]=64.6090 Asic[04]=63.8700 Asic[05]=61.0850 Asic[06]=65.3300 Asic[07]=63.5350 Asic[08]=68.4340
Asic[09]=66.8730 Asic[10]=70.3460 Asic[11]=70.9500 Asic[12]=69.3060 Asic[13]=68.6520 Asic[14]=71.9910 Asic[15]=68.9370 Asic[16]=63.7190
Asic[17]=58.9710 Asic[18]=69.1550

get RT hashrate from Chain[2]: (asic index start from 1-18)
Asic[01]=67.3770 Asic[02]=65.9000 Asic[03]=63.2660 Asic[04]=70.8660 Asic[05]=66.3030 Asic[06]=61.1520 Asic[07]=64.3570 Asic[08]=64.3740
Asic[09]=67.9810 Asic[10]=68.2320 Asic[11]=66.1190 Asic[12]=66.8400 Asic[13]=63.0150 Asic[14]=66.0180 Asic[15]=63.0820 Asic[16]=68.2660
Asic[17]=69.9600 Asic[18]=62.4610

get RT hashrate from Chain[3]: (asic index start from 1-18)
Asic[01]=0.00000 Asic[02]=66.7060 Asic[03]=60.1960 Asic[04]=61.2700 Asic[05]=64.5580 Asic[06]=62.9980 Asic[07]=61.9240 Asic[08]=66.3870
Asic[09]=65.1120 Asic[10]=59.6260 Asic[11]=66.2860 Asic[12]=70.0440 Asic[13]=64.6920 Asic[14]=61.3200 Asic[15]=63.8870 Asic[16]=67.0240
Asic[17]=69.5240 Asic[18]=65.9170

get RT hashrate from Chain[8]: (asic index start from 1-18)
Asic[01]=72.6950 Asic[02]=62.7460 Asic[03]=63.6690 Asic[04]=66.3700 Asic[05]=69.0040 Asic[06]=67.0410 Asic[07]=66.9070 Asic[08]=63.5180
Asic[09]=65.3130 Asic[10]=65.9510 Asic[11]=61.3200 Asic[12]=62.4780 Asic[13]=65.6660 Asic[14]=68.9200 Asic[15]=64.6760 Asic[16]=64.3900
Asic[17]=69.9270 Asic[18]=64.7090

get RT hashrate from Chain[9]: (asic index start from 1-18)
Asic[01]=63.3170 Asic[02]=66.9910 Asic[03]=61.6390 Asic[04]=64.3070 Asic[05]=64.3900 Asic[06]=60.4310 Asic[07]=67.9300 Asic[08]=65.3640
Asic[09]=66.6550 Asic[10]=68.1150 Asic[11]=65.4310 Asic[12]=67.5610 Asic[13]=65.1290 Asic[14]=61.0010 Asic[15]=65.0110 Asic[16]=67.8630
Asic[17]=58.6190 Asic[18]=66.3370

get RT hashrate from Chain[10]: (asic index start from 1-18)
Asic[01]=71.3870 Asic[02]=65.9840 Asic[03]=63.4170 Asic[04]=62.9480 Asic[05]=68.1490 Asic[06]=65.5310 Asic[07]=64.1890 Asic[08]=64.8100
Asic[09]=66.0850 Asic[10]=63.0990 Asic[11]=63.9210 Asic[12]=68.3830 Asic[13]=61.9070 Asic[14]=66.9240 Asic[15]=68.6520 Asic[16]=65.7660
Asic[17]=69.7420 Asic[18]=67.2590

get RT hashrate from Chain[11]: (asic index start from 1-18)
Asic[01]=63.0820 Asic[02]=65.2290 Asic[03]=65.5820 Asic[04]=67.9140 Asic[05]=64.7430 Asic[06]=65.2800 Asic[07]=66.5710 Asic[08]=66.7900
Asic[09]=64.0050 Asic[10]=64.8270 Asic[11]=66.8570 Asic[12]=67.5280 Asic[13]=64.7090 Asic[14]=63.8700 Asic[15]=62.6120 Asic[16]=68.0980
Asic[17]=64.1390 Asic[18]=64.0380

get RT hashrate from Chain[12]: (asic index start from 1-18)
Asic[01]=1.14000 Asic[02]=60.8500 Asic[03]=62.5790 Asic[04]=66.3200 Asic[05]=65.6490 Asic[06]=65.3640 Asic[07]=58.6360 Asic[08]=66.9240
Asic[09]=67.4440 Asic[10]=65.6320 Asic[11]=68.6350 Asic[12]=61.4210 Asic[13]=61.8910 Asic[14]=63.9540 Asic[15]=62.2430 Asic[16]=62.8130
Asic[17]=61.7900 Asic[18]=65.7160

get RT hashrate from Chain[13]: (asic index start from 1-18)
Asic[01]=67.3600 Check Chain[J2] ASIC RT error: (asic index start from 1-18)
Check Chain[J3] ASIC RT error: (asic index start from 1-18)
Check Chain[J4] ASIC RT error: (asic index start from 1-18)
Check Chain[J9] ASIC RT error: (asic index start from 1-18)
Check Chain[J10] ASIC RT error: (asic index start from 1-18)
Check Chain[J11] ASIC RT error: (asic index start from 1-18)
Check Chain[J12] ASIC RT error: (asic index start from 1-18)
Check Chain[J13] ASIC RT error: (asic index start from 1-18)
Check Chain[J14] ASIC RT error: (asic index start from 1-18)
Done check_asic_reg
read failed on Chain[8] Chip[1] middle Temp old value:15
Special fix Chain[8] Chip[1] middle Temp = 15
Done read temp on Chain[8]
Chain[10] Chip[0] pcb temperature=66
Chain[10] Chip[1] junction temperature=84
Special fix Chain[10] Chip[1] middle Temp = 81
Done read temp on Chain[10]
Chain[12] Chip[0] pcb temperature=61
Chain[12] Chip[1] junction temperature=71
Special fix Chain[12] Chip[1] middle Temp = 76
Done read temp on Chain[12]
Max pcb temp : 66
Read temp failed, set fixed full fan speed
FAN PWM: 100
read_temp_func Done!
CRC error counter=43981
salmen148
newbie
Activity: 3
Merit: 0
Re: Antminer T9+ Low Hashrate on chains
June 07, 2018, 06:53:09 AM
#7
I actually found out the problem. It's seems to lie within house wiring. The seller tested at his shop and the machine ran smoothly. What type of wiring would you use? I have 4 240V sockets and an AC wired to a IEC 60898 MCB. I heard the rated voltage of the MCB is under 440V and the rated current is under 125A. Also the cable wire used for this circuit is a 2.5mm cable. I hope this makes sense, I come a complete newbie when it comes to electrical stuff.
BitMaxz
legendary
Activity: 3472
Merit: 3217
Playbet.io - Crypto Casino and Sportsbook
Re: Antminer T9+ Low Hashrate on chains
June 06, 2018, 05:28:43 PM
#6
Quote from: salmen148 on June 03, 2018, 08:03:37 PM
I tried hardreseting, no luck.
My guess your miner is reach the high temperature protection that is why the hashrate is drop.
Could you try this method https://bitcointalksearch.org/topic/solution-for-antminer-s9-fans-speed-up-down-every-20-seconds-2690140
I hope that this method will work in T9+ then setup the fan to high speed and monitor your miner.
If this won't work it might be a hardware issue or some chips from hashing board are broken.
anakinisme
hero member
Activity: 589
Merit: 500
Founder Of miningpuppets
Re: Antminer T9+ Low Hashrate on chains
June 05, 2018, 09:22:31 AM
#5
Quote from: salmen148 on June 03, 2018, 02:03:35 PM
I recently bought a Antminer T9+. The hash rate starts at 10TH/s during the first 10 seconds and then lowers to 7TH/s after a while. However, the decrease is significant on two chains, both running 100 or even 6 GH/s. I think it's not the PSU's fault as I tried on both Bitmain and OEM PSUs. Both PSUs work fine on my S7s. My wall outlet also supports 220 volts and my cord is also rated 220V. I only faced these problems on my S7 if fans were set to AUTO, but the T9+ doesn't have this function. Can anyone help me with this? Thanks in advance.

https://imgur.com/a/CSD4URI

Your B2 error. Run only B2 and see if there is faulty.
Steamtyme
legendary
Activity: 1568
Merit: 2037
Re: Antminer T9+ Low Hashrate on chains
June 03, 2018, 08:28:42 PM
#4
Unfortunately you appear to have the same problem I encountered with these units.

You will have a problem chip in each of the chains that have dropped to around 100 GH/S

My T9+ only has one problem chip and hashes around 9-9.5 TH/S so it wasn't worth sending back to China.


You might find this to be different, if you are located in the US or anywhere else they have outside service centers.

The only thing you can really do is RMA the unit and get it repaired if the cost is worth it for you. I wouldn't even bother getting approval to open it up, as they make you send the entire unit in for repair anyways even if you diagnose the problem area.

After you contact support they will tell you to upgrade the firmware, this did nothing for me but maybe it will help you out if it is a different problem.
salmen148
newbie
Activity: 3
Merit: 0
Re: Antminer T9+ Low Hashrate on chains
June 03, 2018, 08:03:37 PM
#3
Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-gb190cb0-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #57 SMP PREEMPT Fri Dec 9 14:49:22 CST 2016
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 27800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 258048
[    0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map e6fd8000
[    0.000000]   Normal zone: 1520 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 194560 pages, LIFO batch:31
[    0.000000]   HighMem zone: 496 pages used for memmap
[    0.000000]   HighMem zone: 63488 pages, LIFO batch:15
[    0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256528
[    0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 884148K/1032192K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 148044K reserved, 253952K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06d1374   (6949 kB)
[    0.000000]       .init : 0xc06d2000 - 0xc0705380   ( 205 kB)
[    0.000000]       .data : 0xc0706000 - 0xc074cf78   ( 284 kB)
[    0.000000]        .bss : 0xc074cf84 - 0xc078d9fc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to f0004000
[    0.000000] zynq_clock_init: clkc starts at f0004100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000301] ps7-ttc #0 at f0006000, irq=43
[    0.000607] Console: colour dummy device 80x30
[    0.000645] Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096)
[    0.100248] pid_max: default: 32768 minimum: 301
[    0.100475] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.100497] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.102639] CPU: Testing write buffer coherency: ok
[    0.102987] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.103048] Setting up static identity map for 0x4c4af8 - 0x4c4b50
[    0.103269] L310 cache controller enabled
[    0.103289] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.181030] CPU1: Booted secondary processor
[    0.270225] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.270355] Brought up 2 CPUs
[    0.270374] SMP: Total of 2 processors activated.
[    0.270383] CPU: All CPU(s) started in SVC mode.
[    0.271034] devtmpfs: initialized
[    0.273448] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.274653] regulator-dummy: no parameters
[    0.282340] NET: Registered protocol family 16
[    0.284531] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.286807] cpuidle: using governor ladder
[    0.286821] cpuidle: using governor menu
[    0.294233] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.295745] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.295758] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.295871] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[    0.317456] bio: create slab at 0
[    0.318904] vgaarb: loaded
[    0.319613] SCSI subsystem initialized
[    0.320650] usbcore: registered new interface driver usbfs
[    0.320820] usbcore: registered new interface driver hub
[    0.321041] usbcore: registered new device driver usb
[    0.321693] media: Linux media interface: v0.10
[    0.321847] Linux video capture interface: v2.00
[    0.322085] pps_core: LinuxPPS API ver. 1 registered
[    0.322096] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.322220] PTP clock support registered
[    0.322580] EDAC MC: Ver: 3.0.0
[    0.323609] Advanced Linux Sound Architecture Driver Initialized.
[    0.326450] DMA-API: preallocated 4096 debug entries
[    0.326464] DMA-API: debugging enabled by kernel config
[    0.326545] Switched to clocksource arm_global_timer
[    0.346412] NET: Registered protocol family 2
[    0.347473] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.347570] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.347729] TCP: Hash tables configured (established 8192 bind 8192)
[    0.347792] TCP: reno registered
[    0.347811] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.347863] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.348383] NET: Registered protocol family 1
[    0.348824] RPC: Registered named UNIX socket transport module.
[    0.348837] RPC: Registered udp transport module.
[    0.348845] RPC: Registered tcp transport module.
[    0.348854] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.348866] PCI: CLS 0 bytes, default 64
[    0.349305] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.351305] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.352713] bounce pool size: 64 pages
[    0.353595] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.353800] msgmni has been set to 1486
[    0.354575] io scheduler noop registered
[    0.354588] io scheduler deadline registered
[    0.354632] io scheduler cfq registered (default)
[    0.370520] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.370540] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.492964] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    1.065845] console [ttyPS0] enabled
[    1.070137] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[    1.077789] [drm] Initialized drm 1.1.0 20060810
[    1.094636] brd: module loaded
[    1.103983] loop: module loaded
[    1.113385] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.119215] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.126969] libphy: XEMACPS mii bus: probed
[    1.131336] ------------- phy_id = 0x3625e62
[    1.136061] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.145002] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.151849] ehci-pci: EHCI PCI platform driver
[    1.159082] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.165885] usbcore: registered new interface driver usb-storage
[    1.172760] mousedev: PS/2 mouse device common for all mice
[    1.178884] i2c /dev entries driver
[    1.185759] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.191289] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.197195] Xilinx Zynq CpuIdle Driver started
[    1.202059] sdhci: Secure Digital Host Controller Interface driver
[    1.208205] sdhci: Copyright(c) Pierre Ossman
[    1.212493] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.219366] mmc0: no vqmmc regulator found
[    1.223381] mmc0: no vmmc regulator found
[    1.266567] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.275254] usbcore: registered new interface driver usbhid
[    1.280763] usbhid: USB HID core driver
[    1.285481] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.291778] nand: Micron MT29F2G08ABAEAWP
[    1.295746] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.301687] Bad block table found at page 131008, version 0x01
[    1.307911] Bad block table found at page 130944, version 0x01
[    1.313967] 3 ofpart partitions found on MTD device pl353-nand
[    1.319744] Creating 3 MTD partitions on "pl353-nand":
[    1.324837] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.332908] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.340218] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.349151] TCP: cubic registered
[    1.352384] NET: Registered protocol family 17
[    1.357110] Registering SWP/SWPB emulation handler
[    1.363005] regulator-dummy: disabling
[    1.367334] UBI: attaching mtd1 to ubi0
[    1.892492] UBI: scanning is finished
[    1.904116] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.911192] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.917956] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.924620] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.931497] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.937478] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.944585] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 862493722
[    1.953541] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.962757] UBI: background thread "ubi_bgt0d" started, PID 1080
[    1.962762] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.966743] ALSA device list:
[    1.966746]   No soundcards found.
[    1.983113] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[    2.012276] UBIFS: recovery needed
[    2.080893] UBIFS: recovery completed
[    2.084563] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.090511] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.099617] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.109506] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.114535] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 2A24A8E1-2021-4A54-8A4E-D8E294AE00E5, small LPT model
[    2.126063] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.133266] devtmpfs: mounted
[    2.136372] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[    2.981721] random: dd urandom read with 0 bits of entropy available
[    3.396582]
[    3.396582] bcm54xx_config_init
[    4.006588]
[    4.006588] bcm54xx_config_init
[    8.007427] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    8.013515] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   24.724791] In axi fpga driver!
[   24.727899] request_mem_region OK!
[   24.731251] AXI fpga dev virtual address is 0xf01fe000
[   24.736357] *base_vir_addr = 0xc510
[   24.751551] In fpga mem driver!
[   24.754673] request_mem_region OK!
[   24.758273] fpga mem virtual address is 0xf3000000
[   25.536581]
[   25.536581] bcm54xx_config_init
[   26.166571]
[   26.166571] bcm54xx_config_init
[   30.167434] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   30.173453] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  394.349490] random: nonblocking pool is initialized
This is XILINX board. Totalram:       1039794176
Detect 1GB control board of XILINX
DETECT HW version=8000c510
miner ID : 805454411375885c
Miner Type = T9+
AsicType = 1387
real AsicNum = 18
use critical mode to search freq...
get PLUG ON=0x07003f0e
Find hashboard on Chain[1]
Find hashboard on Chain[2]
Find hashboard on Chain[3]
Find hashboard on Chain[8]
Find hashboard on Chain[9]
Find hashboard on Chain[10]
Find hashboard on Chain[11]
Find hashboard on Chain[12]
Find hashboard on Chain[13]
set_reset_allhashboard = 0x0000ffff
chain[1] PIC jump to app
Check chain[1] PIC fw version=0x03
chain[2] PIC jump to app
Check chain[2] PIC fw version=0x03
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x03
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0x4a 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x4a 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x4a 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [22:5] [24:24] [70:85] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[1] has freq in PIC and will jump over...
Chain[1] has core num in PIC
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0x47 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x47 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x47 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [22:5] [24:32] [33:38] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[2] has freq in PIC and will jump over...
Chain[2] has core num in PIC
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0x41 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x41 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x41 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [22:5] [24:25] [88:80] [255:255] [255:255] [255:255] [255:255] [255:255]
has freq in PIC, will disable freq setting.
chain[3] has freq in PIC and will jump over...
Chain[3] has core num in PIC
has freq in PIC, will disable freq setting.
chain[8] has freq in PIC and will jump over...
Chain[8] has core num in PIC
has freq in PIC, will disable freq setting.
chain[9] has freq in PIC and will jump over...
Chain[9] has core num in PIC
has freq in PIC, will disable freq setting.
chain[10] has freq in PIC and will jump over...
Chain[10] has core num in PIC
has freq in PIC, will disable freq setting.
chain[11] has freq in PIC and will jump over...
Chain[11] has core num in PIC
has freq in PIC, will disable freq setting.
chain[12] has freq in PIC and will jump over...
Chain[12] has core num in PIC
has freq in PIC, will disable freq setting.
chain[13] has freq in PIC and will jump over...
Chain[13] has core num in PIC
get PIC voltage=11 on chain[1], value=870
get PIC voltage=11 on chain[2], value=870
get PIC voltage=11 on chain[3], value=870
get PIC voltage=11 on chain[8], value=870
get PIC voltage=11 on chain[9], value=870
get PIC voltage=11 on chain[10], value=870
get PIC voltage=11 on chain[11], value=870
get PIC voltage=11 on chain[12], value=870
get PIC voltage=11 on chain[13], value=870
set_reset_allhashboard = 0x00000000
chain[8] temp offset record: 1,-4,0,0,0,0,0,0
chain[8] temp chip I2C addr=0x98
chain[10] temp offset record: 1,-4,0,0,0,0,0,0
chain[10] temp chip I2C addr=0x98
chain[12] temp offset record: 1,-4,0,0,0,0,0,0
chain[12] temp chip I2C addr=0x98
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 9, total chain num = 9
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found=23916 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 1GB control board of XILINX
Miner Type = T9+
Miner compile time: Fri Nov 24 23:19:16 EST 2017 type: Antminer T9+set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 805454411375885c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[5] speed=4320
get fan[2] speed=6120
get fan[5] speed=4320
get fan[2] speed=6120
get fan[5] speed=4320
chain[1] PIC jump to app
Check chain[1] PIC fw version=0x03
Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0x4a 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x4a 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x4a 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[1]: [22:5] [24:24] [70:85] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J2] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J2] test patten OK temp=74
chain[2] PIC jump to app
Check chain[2] PIC fw version=0x03
Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0x47 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x47 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x47 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[2]: [22:5] [24:32] [33:38] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J3] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J3] test patten OK temp=71
chain[3] PIC jump to app
Check chain[3] PIC fw version=0x03
Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0x41 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x41 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0x41 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
chain[3]: [22:5] [24:25] [88:80] [255:255] [255:255] [255:255] [255:255] [255:255]
Chain[J4] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J4] test patten OK temp=65
Chain[J9] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J9] test patten OK temp=74
Chain[J10] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J10] test patten OK temp=74
Chain[J11] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J11] test patten OK temp=71
Chain[J12] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J12] test patten OK temp=71
Chain[J13] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J13] test patten OK temp=65
Chain[J14] has backup chain_voltage=870
Detect: use voltage limit rules on single board!
Detect: T9+ use voltage level=1
Chain[J14] test patten OK temp=65
Chain[J2] will use voltage=930 [1] to open core
Chain[J3] will use voltage=930 [1] to open core
Chain[J4] will use voltage=930 [1] to open core
Chain[J9] will use voltage=930 [1] to open core
Chain[J10] will use voltage=930 [1] to open core
Chain[J11] will use voltage=930 [1] to open core
Chain[J12] will use voltage=930 [1] to open core
Chain[J13] will use voltage=930 [1] to open core
Chain[J14] will use voltage=930 [1] to open core
Chain[J2] orignal chain_voltage_pic=11 value=870
Chain[J3] orignal chain_voltage_pic=11 value=870
Chain[J4] orignal chain_voltage_pic=11 value=870
Chain[J9] orignal chain_voltage_pic=1 value=930
Chain[J9] will use backup chain_voltage_pic=870 [11]
Chain[J9] get working chain_voltage_pic=11
Chain[J10] orignal chain_voltage_pic=1 value=930
Chain[J10] will use backup chain_voltage_pic=870 [11]
Chain[J10] get working chain_voltage_pic=11
Chain[J11] orignal chain_voltage_pic=1 value=930
Chain[J11] will use backup chain_voltage_pic=870 [11]
Chain[J11] get working chain_voltage_pic=11
Chain[J12] orignal chain_voltage_pic=1 value=930
Chain[J12] will use backup chain_voltage_pic=870 [11]
Chain[J12] get working chain_voltage_pic=11
Chain[J13] orignal chain_voltage_pic=1 value=930
Chain[J13] will use backup chain_voltage_pic=870 [11]
Chain[J13] get working chain_voltage_pic=11
Chain[J14] orignal chain_voltage_pic=1 value=930
Chain[J14] will use backup chain_voltage_pic=870 [11]
Chain[J14] get working chain_voltage_pic=11
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
T9+ try get asic num for the 1 time
Chain[J2] has 18 asic
Chain[J3] has 18 asic
Chain[J4] has 18 asic
Chain[J9] has 18 asic
Chain[J10] has 18 asic
Chain[J11] has 18 asic
Chain[J12] has 18 asic
Chain[J13] has 18 asic
Chain[J14] has 18 asic
Chain[J2] has core num in PIC
Chain[J3] has core num in PIC
Chain[J4] has core num in PIC
Chain[J9] has core num in PIC
Chain[J10] has core num in PIC
Chain[J11] has core num in PIC
Chain[J12] has core num in PIC
Chain[J13] has core num in PIC
Chain[J14] has core num in PIC
miner total rate=10619GH/s fixed rate=10500GH/s
read PIC voltage=930 on chain[1]
Chain:1 chipnum=18
Chain[J2] voltage added=0.0V
Chain:1 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:1 max freq=575
Chain:1 min freq=575

read PIC voltage=930 on chain[2]
Chain:2 chipnum=18
Chain[J3] voltage added=0.0V
Chain:2 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:2 max freq=575
Chain:2 min freq=575

read PIC voltage=930 on chain[3]
Chain:3 chipnum=18
Chain[J4] voltage added=0.0V
Chain:3 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:3 max freq=575
Chain:3 min freq=575

read PIC voltage=930 on chain[8]
Chain:8 chipnum=18
Chain[J9] voltage added=0.0V
Chain:8 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:8 max freq=575
Chain:8 min freq=575

read PIC voltage=930 on chain[9]
Chain:9 chipnum=18
Chain[J10] voltage added=0.0V
Chain:9 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:9 max freq=575
Chain:9 min freq=575

read PIC voltage=930 on chain[10]
Chain:10 chipnum=18
Chain[J11] voltage added=0.0V
Chain:10 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:10 max freq=575
Chain:10 min freq=575

read PIC voltage=930 on chain[11]
Chain:11 chipnum=18
Chain[J12] voltage added=0.0V
Chain:11 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:11 max freq=575
Chain:11 min freq=575

read PIC voltage=930 on chain[12]
Chain:12 chipnum=18
Chain[J13] voltage added=0.0V
Chain:12 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:12 max freq=575
Chain:12 min freq=575

read PIC voltage=930 on chain[13]
Chain:13 chipnum=18
Chain[J14] voltage added=0.0V
Chain:13 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:13 max freq=575
Chain:13 min freq=575


Miner fix freq ...
read PIC voltage=930 on chain[1]
Chain:1 chipnum=18
Chain[J2] voltage added=0.0V
Chain:1 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:1 max freq=575
Chain:1 min freq=575

read PIC voltage=930 on chain[2]
Chain:2 chipnum=18
Chain[J3] voltage added=0.0V
Chain:2 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:2 max freq=575
Chain:2 min freq=575

read PIC voltage=930 on chain[3]
Chain:3 chipnum=18
Chain[J4] voltage added=0.0V
Chain:3 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:3 max freq=575
Chain:3 min freq=575

read PIC voltage=930 on chain[8]
Chain:8 chipnum=18
Chain[J9] voltage added=0.0V
Chain:8 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:8 max freq=575
Chain:8 min freq=575

read PIC voltage=930 on chain[9]
Chain:9 chipnum=18
Chain[J10] voltage added=0.0V
Chain:9 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:9 max freq=575
Chain:9 min freq=575

read PIC voltage=930 on chain[10]
Chain:10 chipnum=18
Chain[J11] voltage added=0.0V
Chain:10 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:10 max freq=575
Chain:10 min freq=575

read PIC voltage=930 on chain[11]
Chain:11 chipnum=18
Chain[J12] voltage added=0.0V
Chain:11 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:11 max freq=575
Chain:11 min freq=575

read PIC voltage=930 on chain[12]
Chain:12 chipnum=18
Chain[J13] voltage added=0.0V
Chain:12 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:12 max freq=575
Chain:12 min freq=575

read PIC voltage=930 on chain[13]
Chain:13 chipnum=18
Chain[J14] voltage added=0.0V
Chain:13 base freq=575
Asic[ 0]:575
Asic[ 1]:575 Asic[ 2]:575 Asic[ 3]:575 Asic[ 4]:575 Asic[ 5]:575 Asic[ 6]:575 Asic[ 7]:575 Asic[ 8]:575
Asic[ 9]:575 Asic[10]:575 Asic[11]:575 Asic[12]:575 Asic[13]:575 Asic[14]:575 Asic[15]:575 Asic[16]:575
Asic[17]:575
Chain:13 max freq=575
Chain:13 min freq=575

max freq = 575
set baud=1
Chain[J9] PIC temp offset=1,-4,0,0,0,0,0,0
chain[8] temp chip I2C addr=0x98
chain[8] has no middle temp, use special fix mode.
Chain[J9] chip[0] use PIC middle temp offset=-4 typeID=55
New offset Chain[8] chip[0] local:23 remote:26 offset:26
Chain[J9] chip[0] get middle temp offset=26 typeID=55
Chain[J11] PIC temp offset=1,-4,0,0,0,0,0,0
chain[10] temp chip I2C addr=0x98
chain[10] has no middle temp, use special fix mode.
Chain[J11] chip[0] use PIC middle temp offset=-4 typeID=55
New offset Chain[10] chip[0] local:24 remote:28 offset:26
Chain[J11] chip[0] get middle temp offset=26 typeID=55
Chain[J13] PIC temp offset=1,-4,0,0,0,0,0,0
chain[12] temp chip I2C addr=0x98
chain[12] has no middle temp, use special fix mode.
Chain[J13] chip[0] use PIC middle temp offset=-4 typeID=55
New offset Chain[12] chip[0] local:26 remote:30 offset:26
Chain[J13] chip[0] get middle temp offset=26 typeID=55
single board rate=1179 voltage limit=870 on chain[1]
get PIC voltage=870 on chain[1], check: must be < 870
single board rate=1179 voltage limit=870 on chain[2]
get PIC voltage=870 on chain[2], check: must be < 870
single board rate=1179 voltage limit=870 on chain[3]
get PIC voltage=870 on chain[3], check: must be < 870
single board rate=1179 voltage limit=870 on chain[8]
get PIC voltage=870 on chain[8], check: must be < 870
single board rate=1179 voltage limit=870 on chain[9]
get PIC voltage=870 on chain[9], check: must be < 870
single board rate=1179 voltage limit=870 on chain[10]
get PIC voltage=870 on chain[10], check: must be < 870
single board rate=1179 voltage limit=870 on chain[11]
get PIC voltage=870 on chain[11], check: must be < 870
single board rate=1179 voltage limit=870 on chain[12]
get PIC voltage=870 on chain[12], check: must be < 870
single board rate=1179 voltage limit=870 on chain[13]
get PIC voltage=870 on chain[13], check: must be < 870
open core on chain[1] [8] [9]...
set voltage=870 on chain[1], the real voltage=870
Chain[J2] set working voltage=870 [11]
open core on chain[2] [10] [11]...
set voltage=870 on chain[2], the real voltage=870
Chain[J3] set working voltage=870 [11]
open core on chain[3] [12] [13]...
set voltage=870 on chain[3], the real voltage=870
Chain[J4] set working voltage=870 [11]
setStartTimePoint total_tv_start_sys=713 total_tv_end_sys=714
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08

get RT hashrate from Chain[1]: (asic index start from 1-18)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000

get RT hashrate from Chain[2]: (asic index start from 1-18)
Asic[01]=12.8840 Asic[02]=12.8840 Asic[03]=8.58900 Asic[04]=4.29400 Asic[05]=12.8840 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=8.58900
Asic[09]=12.8840 Asic[10]=8.58900 Asic[11]=0.00000 Asic[12]=12.8840 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=4.29400
Asic[17]=0.00000 Asic[18]=8.58900

get RT hashrate from Chain[3]: (asic index start from 1-18)
Asic[01]=85.8990 Asic[02]=19.8640 Asic[03]=15.5690 Asic[04]=17.1790 Asic[05]=47.2440 Asic[06]=8.85800 Asic[07]=10.2000 Asic[08]=11.2740
Asic[09]=77.3090 Asic[10]=7.24700 Asic[11]=7.78400 Asic[12]=73.0140 Asic[13]=9.12600 Asic[14]=7.51600 Asic[15]=19.0580 Asic[16]=20.9370
Asic[17]=9.39500 Asic[18]=14.2270

get RT hashrate from Chain[8]: (asic index start from 1-18)
Asic[01]=640.319 Asic[02]=16.6590 Asic[03]=12.5660 Asic[04]=27.0780 Asic[05]=19.7970 Asic[06]=14.5960 Asic[07]=76.8560 Asic[08]=69.5580
Asic[09]=14.7130 Asic[10]=15.7700 Asic[11]=88.3650 Asic[12]=19.9810 Asic[13]=19.1420 Asic[14]=16.3410 Asic[15]=22.9000 Asic[16]=16.8270
Asic[17]=19.2600 Asic[18]=18.8240

get RT hashrate from Chain[9]: (asic index start from 1-18)
Asic[01]=27.2290 Asic[02]=21.6420 Asic[03]=16.3910 Asic[04]=22.0110 Asic[05]=71.0010 Asic[06]=18.4210 Asic[07]=20.7030 Asic[08]=19.9640
Asic[09]=20.8370 Asic[10]=16.9610 Asic[11]=14.9140 Asic[12]=96.0830 Asic[13]=19.5620 Asic[14]=67.5450 Asic[15]=95.7300 Asic[16]=73.0140
Asic[17]=19.6790 Asic[18]=56.2870

get RT hashrate from Chain[10]: (asic index start from 1-18)
Asic[01]=23.3030 Asic[02]=28.9230 Asic[03]=29.0240 Asic[04]=27.2290 Asic[05]=62.3940 Asic[06]=33.1680 Asic[07]=54.8270 Asic[08]=26.2060
Asic[09]=21.2060 Asic[10]=22.0620 Asic[11]=57.7970 Asic[12]=59.8770 Asic[13]=103.297 Asic[14]=21.3400 Asic[15]=71.5540 Asic[16]=33.0170
Asic[17]=25.5010 Asic[18]=27.9670

get RT hashrate from Chain[11]: (asic index start from 1-18)
Asic[01]=27.5310 Asic[02]=64.6090 Asic[03]=84.9090 Asic[04]=28.1520 Asic[05]=32.3630 Asic[06]=28.1680 Asic[07]=30.1150 Asic[08]=24.9810
Asic[09]=28.9070 Asic[10]=27.2120 Asic[11]=25.9200 Asic[12]=31.2720 Asic[13]=71.0680 Asic[14]=69.1890 Asic[15]=27.8830 Asic[16]=37.4630
Asic[17]=29.2420 Asic[18]=70.5640

get RT hashrate from Chain[12]: (asic index start from 1-18)
Asic[01]=53.3850 Asic[02]=37.6980 Asic[03]=81.7720 Asic[04]=32.9000 Asic[05]=31.1880 Asic[06]=28.1010 Asic[07]=36.3890 Asic[08]=28.7050
Asic[09]=29.2930 Asic[10]=60.8170 Asic[11]=65.4310 Asic[12]=31.3560 Asic[13]=37.9500 Asic[14]=29.8960 Asic[15]=31.2050 Asic[16]=36.6410
Asic[17]=31.4900 Asic[18]=37.7820

get RT hashrate from Chain[13]: (asic index start from 1-18)
Asic[01]=35.5840 Asic[02]=34.3090 Asic[03]=53.1660 Asic[04]=69.8600 Asic[05]=69.9600 Asic[06]=57.9980 Asic[07]=32.0270 Asic[08]=32.9160
Asic[09]=73.4500 Asic[10]=61.9410 Asic[11]=35.1810 Asic[12]=35.9870 Asic[13]=40.0130 Asic[14]=71.5210 Asic[15]=34.8960 Asic[16]=34.9130
Asic[17]=40.9360 Asic[18]=36.7920
Check Chain[J2] ASIC RT error: (asic index start from 1-18)
Check Chain[J3] ASIC RT error: (asic index start from 1-18)
Check Chain[J4] ASIC RT error: (asic index start from 1-18)
Check Chain[J9] ASIC RT error: (asic index start from 1-18)
Asic[01]=640.319000
Check Chain[J10] ASIC RT error: (asic index start from 1-18)
Check Chain[J11] ASIC RT error: (asic index start from 1-18)
Asic[13]=103.297000
Check Chain[J12] ASIC RT error: (asic index start from 1-18)
Check Chain[J13] ASIC RT error: (asic index start from 1-18)
Check Chain[J14] ASIC RT error: (asic index start from 1-18)
Done check_asic_reg
do read temp on Chain[8]
Chain[8] Chip[1] TempTypeID=55 middle offset=26
read failed, old value: Chain[8] Chip[1] local Temp=0
Chain[8] Chip[1] middle Temp=54
Special fix Chain[8] Chip[1] middle Temp = 15
Done read temp on Chain[8]
do read temp on Chain[10]
Chain[10] Chip[1] TempTypeID=55 middle offset=26
read failed, old value: Chain[10] Chip[1] local Temp=0
Chain[10] Chip[1] middle Temp=56
Special fix Chain[10] Chip[1] middle Temp = 15
Done read temp on Chain[10]
do read temp on Chain[12]
Chain[12] Chip[1] TempTypeID=55 middle offset=26
read failed, old value: Chain[12] Chip[1] local Temp=0
Chain[12] Chip[1] middle Temp=56
Special fix Chain[12] Chip[1] middle Temp = 15
Done read temp on Chain[12]
Set fixed full fan speed
FAN PWM: 100
read_temp_func Done!
CRC error counter=0

I tried hardreseting, no luck.
BitMaxz
legendary
Activity: 3472
Merit: 3217
Playbet.io - Crypto Casino and Sportsbook
Re: Antminer T9+ Low Hashrate on chains
June 03, 2018, 04:06:32 PM
#2
Could you paste the kernel logs on pastebin or here just use the "insert code".

I think you can fix this by hard resetting your T9+ miner, you follow the guide here on how to restore factory your miner follow this https://enforum.bitmain.com/bbs/topics/3957
salmen148
newbie
Activity: 3
Merit: 0
Re: Antminer T9+ Low Hashrate on chains
June 03, 2018, 02:03:35 PM
#1
I recently bought a Antminer T9+. The hash rate starts at 10TH/s during the first 10 seconds and then lowers to 7TH/s after a while. However, the decrease is significant on two chains, both running 100 or even 6 GH/s. I think it's not the PSU's fault as I tried on both Bitmain and OEM PSUs. Both PSUs work fine on my S7s. My wall outlet also supports 220 volts and my cord is also rated 220V. I only faced these problems on my S7 if fans were set to AUTO, but the T9+ doesn't have this function. Can anyone help me with this? Thanks in advance.

https://imgur.com/a/CSD4URI
Bitcoin Forum>Bitcoin>Mining>Mining support
Jump to: