Bitcoin Forum>Bitcoin>Mining>Mining support
Author

Topic: Antminer T9+ Low hashrate problem!!! (Read 272 times)

mikeywith
legendary
Activity: 2436
Merit: 6643
be constructive or S.T.F.U
Antminer T9+ Low hashrate problem!!!
June 20, 2020, 02:03:22 PM
#3
Edit the post and use the code function to paste the kernel log, this post looks messy.

Anway, the answer is here

Code:
driver-btm-c5.c:11856:T9_18_getASICnum: T9+ try get asic num for the 1 time
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J2] has 0 asic
driver-btm-c5.c:11856:T9_18_getASICnum: T9+ try get asic num for the 2 time

J2 (Usually the middle board) is toasted, while this kernel log tells you where the problem is, it's not very accurate, it doesn't really mean that all chips on this chain are gone, it could be a single chip which causes the whole chain to disappear that's because of how these hash boards are designed, it could also be a power module, or any other component, troubleshooting and fixing this kind of an issue will cost you more than what the board actually worth, so usually the best way to deal with this is by sending it to the trash.

There is however a small possibility that the PSU is faulty and it can't power all boards, to troubleshoot this, disconnect the other chains, keep chain 2 only, use a different ribbon and 6pin cables on chain 2 then power on, if the same issue appears then the board is dead but, if something changes then it's either a bad PSU or a ribbon cable.
Philipma1957cellphone
full member
Activity: 416
Merit: 125
Re: Antminer T9+ Low hashrate problem!!!
June 20, 2020, 06:28:03 AM
#2
Your temp sensor has failed. You can play with firmware you could get lucky please put your log in code. I DONT think braiins os does t9 let me check just went to braiins website they work on s9.
Jackflash712
newbie
Activity: 1
Merit: 0
Re: Antminer T9+ Low hashrate problem!!!
June 20, 2020, 02:36:00 AM
#1
Hello everybody!!   Cheesy Cheesy Cheesy  i have a low hashrate problem with my Antminer T9+!!

2, 9 10 chains (J2) don´t work. So, the miner works at 7.5 TH/s instead 0f 10.5TH/s. I reboot the miner... then load the last firmware and the problem persists.

Now i overcloacked the working chains to 631 to gain 1 TH/s.

The problem strarted 3 days ago...in normal conditions..

(I note that J2 board is detached, its move a lot)

kernel log shows:

Code:
main.c:14758: bmminer not found, restart bmminer ...
driver-btm-c5.c:12285:bitmain_c5_init: This is user mode for mining
driver-btm-c5.c:12334:bitmain_c5_init: Detect 512MB control board of XILINX
driver-btm-c5.c:12363:bitmain_c5_init: Miner Type = T9+
driver-btm-c5.c:12366:bitmain_c5_init: Miner compile time: Tue Jul 30 20:56:54 CST 2019 type: Antminer T9+
driver-btm-c5.c:12456:bitmain_c5_init: miner ID : 81140c0268808814
driver-btm-c5.c:12613:bitmain_c5_init: Checking fans...
driver-btm-c5.c:2990:check_fan_beforeInit: get fan[4] speed=5880
driver-btm-c5.c:2990:check_fan_beforeInit: get fan[5] speed=5760
driver-btm-c5.c:2990:check_fan_beforeInit: get fan[4] speed=5880
driver-btm-c5.c:2990:check_fan_beforeInit: get fan[5] speed=5760
driver-btm-c5.c:2990:check_fan_beforeInit: get fan[4] speed=5880
driver-btm-c5.c:2990:check_fan_beforeInit: get fan[5] speed=5760
driver-btm-c5.c:1664:jump_to_app_CheckAndRestorePIC_T9_18: chain[1] PIC jump to app
driver-btm-c5.c:1669:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[1] PIC fw version=0x90
driver-btm-c5.c:12666:bitmain_c5_init: Chain[1] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x55 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:12680:bitmain_c5_init: chain[1]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
driver-btm-c5.c:12825:bitmain_c5_init: Chain[J2] has backup chain_voltage=870
driver-btm-c5.c:12835:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:12841:bitmain_c5_init: Detect: T9+ use voltage level=1
driver-btm-c5.c:12849:bitmain_c5_init: Chain[J2] test patten OK temp=-1
driver-btm-c5.c:1664:jump_to_app_CheckAndRestorePIC_T9_18: chain[2] PIC jump to app
driver-btm-c5.c:1669:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[2] PIC fw version=0x90
driver-btm-c5.c:12666:bitmain_c5_init: Chain[2] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:12680:bitmain_c5_init: chain[2]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
driver-btm-c5.c:12825:bitmain_c5_init: Chain[J3] has backup chain_voltage=870
driver-btm-c5.c:12835:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:12841:bitmain_c5_init: Detect: T9+ use voltage level=1
driver-btm-c5.c:12849:bitmain_c5_init: Chain[J3] test patten OK temp=-1
driver-btm-c5.c:1664:jump_to_app_CheckAndRestorePIC_T9_18: chain[3] PIC jump to app
driver-btm-c5.c:1669:jump_to_app_CheckAndRestorePIC_T9_18: Check chain[3] PIC fw version=0x90
driver-btm-c5.c:12666:bitmain_c5_init: Chain[3] read_freq_badcores : 0x7d 0x33 0x33 0x33 0x11 0x33 0x33 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x3e 0x57 0x00 0xff 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x3e 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff 0xff
driver-btm-c5.c:12680:bitmain_c5_init: chain[3]: [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255] [255:255]
driver-btm-c5.c:12825:bitmain_c5_init: Chain[J4] has backup chain_voltage=870
driver-btm-c5.c:12835:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:12841:bitmain_c5_init: Detect: T9+ use voltage level=1
driver-btm-c5.c:12849:bitmain_c5_init: Chain[J4] test patten OK temp=-1
driver-btm-c5.c:12825:bitmain_c5_init: Chain[J9] has backup chain_voltage=870
driver-btm-c5.c:12835:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:12841:bitmain_c5_init: Detect: T9+ use voltage level=1
driver-btm-c5.c:12849:bitmain_c5_init: Chain[J9] test patten OK temp=-1
driver-btm-c5.c:12825:bitmain_c5_init: Chain[J10] has backup chain_voltage=870
driver-btm-c5.c:12835:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:12841:bitmain_c5_init: Detect: T9+ use voltage level=1
driver-btm-c5.c:12849:bitmain_c5_init: Chain[J10] test patten OK temp=-1
driver-btm-c5.c:12825:bitmain_c5_init: Chain[J11] has backup chain_voltage=870
driver-btm-c5.c:12835:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:12841:bitmain_c5_init: Detect: T9+ use voltage level=1
driver-btm-c5.c:12849:bitmain_c5_init: Chain[J11] test patten OK temp=-1
driver-btm-c5.c:12825:bitmain_c5_init: Chain[J12] has backup chain_voltage=870
driver-btm-c5.c:12835:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:12841:bitmain_c5_init: Detect: T9+ use voltage level=1
driver-btm-c5.c:12849:bitmain_c5_init: Chain[J12] test patten OK temp=-1
driver-btm-c5.c:12825:bitmain_c5_init: Chain[J13] has backup chain_voltage=870
driver-btm-c5.c:12835:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:12841:bitmain_c5_init: Detect: T9+ use voltage level=1
driver-btm-c5.c:12849:bitmain_c5_init: Chain[J13] test patten OK temp=-1
driver-btm-c5.c:12825:bitmain_c5_init: Chain[J14] has backup chain_voltage=870
driver-btm-c5.c:12835:bitmain_c5_init: Detect: use voltage limit rules on single board!
driver-btm-c5.c:12841:bitmain_c5_init: Detect: T9+ use voltage level=1
driver-btm-c5.c:12849:bitmain_c5_init: Chain[J14] test patten OK temp=-1
driver-btm-c5.c:12237:init_exist_chain_table: total_exist_chain_num = 9
driver-btm-c5.c:13278:bitmain_c5_init: Chain[J2] will use voltage=890 [7] to open core
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 7 seccessful
driver-btm-c5.c:13278:bitmain_c5_init: Chain[J3] will use voltage=890 [7] to open core
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 7 seccessful
driver-btm-c5.c:13278:bitmain_c5_init: Chain[J4] will use voltage=890 [7] to open core
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 7 seccessful
driver-btm-c5.c:13278:bitmain_c5_init: Chain[J9] will use voltage=890 [7] to open core
driver-btm-c5.c:13278:bitmain_c5_init: Chain[J10] will use voltage=890 [7] to open core
driver-btm-c5.c:13278:bitmain_c5_init: Chain[J11] will use voltage=890 [7] to open core
driver-btm-c5.c:13278:bitmain_c5_init: Chain[J12] will use voltage=890 [7] to open core
driver-btm-c5.c:13278:bitmain_c5_init: Chain[J13] will use voltage=890 [7] to open core
driver-btm-c5.c:13278:bitmain_c5_init: Chain[J14] will use voltage=890 [7] to open core
btm_adjust_hash.c:922:adjust_vol: Chain[J2] original vol value=870 adjusted vol value:870
driver-btm-c5.c:13361:bitmain_c5_init: Chain[J2] orignal chain_voltage_pic=7 value=890
driver-btm-c5.c:13362:bitmain_c5_init: Chain[J2] original chain_voltage_value=870 adjusted chain_voltage_value:870, value=890
driver-btm-c5.c:13379:bitmain_c5_init: Chain[J2] will use backup chain_voltage_pic=870 [11]
driver-btm-c5.c:13389:bitmain_c5_init: Chain[J2] get working chain_voltage_pic=11
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[00] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[01] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[02] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[03] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[04] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[05] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[06] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[07] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[08] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[09] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[10] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[11] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[12] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[13] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[14] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[15] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[16] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J2] Aisc[17] original freq=575 adjusted freq:631
btm_adjust_hash.c:922:adjust_vol: Chain[J3] original vol value=870 adjusted vol value:870
driver-btm-c5.c:13361:bitmain_c5_init: Chain[J3] orignal chain_voltage_pic=7 value=890
driver-btm-c5.c:13362:bitmain_c5_init: Chain[J3] original chain_voltage_value=870 adjusted chain_voltage_value:870, value=890
driver-btm-c5.c:13379:bitmain_c5_init: Chain[J3] will use backup chain_voltage_pic=870 [11]
driver-btm-c5.c:13389:bitmain_c5_init: Chain[J3] get working chain_voltage_pic=11
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[00] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[01] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[02] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[03] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[04] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[05] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[06] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[07] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[08] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[09] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[10] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[11] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[12] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[13] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[14] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[15] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[16] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J3] Aisc[17] original freq=575 adjusted freq:631
btm_adjust_hash.c:922:adjust_vol: Chain[J4] original vol value=870 adjusted vol value:870
driver-btm-c5.c:13361:bitmain_c5_init: Chain[J4] orignal chain_voltage_pic=7 value=890
driver-btm-c5.c:13362:bitmain_c5_init: Chain[J4] original chain_voltage_value=870 adjusted chain_voltage_value:870, value=890
driver-btm-c5.c:13379:bitmain_c5_init: Chain[J4] will use backup chain_voltage_pic=870 [11]
driver-btm-c5.c:13389:bitmain_c5_init: Chain[J4] get working chain_voltage_pic=11
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[00] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[01] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[02] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[03] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[04] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[05] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[06] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[07] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[08] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[09] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[10] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[11] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[12] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[13] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[14] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[15] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[16] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J4] Aisc[17] original freq=575 adjusted freq:631
btm_adjust_hash.c:922:adjust_vol: Chain[J9] original vol value=870 adjusted vol value:870
driver-btm-c5.c:13361:bitmain_c5_init: Chain[J9] orignal chain_voltage_pic=7 value=890
driver-btm-c5.c:13362:bitmain_c5_init: Chain[J9] original chain_voltage_value=870 adjusted chain_voltage_value:870, value=890
driver-btm-c5.c:13379:bitmain_c5_init: Chain[J9] will use backup chain_voltage_pic=870 [11]
driver-btm-c5.c:13389:bitmain_c5_init: Chain[J9] get working chain_voltage_pic=11
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[00] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[01] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[02] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[03] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[04] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[05] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[06] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[07] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[08] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[09] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[10] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[11] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[12] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[13] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[14] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[15] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[16] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J9] Aisc[17] original freq=575 adjusted freq:631
btm_adjust_hash.c:922:adjust_vol: Chain[J10] original vol value=870 adjusted vol value:870
driver-btm-c5.c:13361:bitmain_c5_init: Chain[J10] orignal chain_voltage_pic=7 value=890
driver-btm-c5.c:13362:bitmain_c5_init: Chain[J10] original chain_voltage_value=870 adjusted chain_voltage_value:870, value=890
driver-btm-c5.c:13379:bitmain_c5_init: Chain[J10] will use backup chain_voltage_pic=870 [11]
driver-btm-c5.c:13389:bitmain_c5_init: Chain[J10] get working chain_voltage_pic=11
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[00] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[01] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[02] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[03] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[04] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[05] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[06] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[07] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[08] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[09] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[10] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[11] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[12] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[13] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[14] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[15] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[16] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J10] Aisc[17] original freq=575 adjusted freq:631
btm_adjust_hash.c:922:adjust_vol: Chain[J11] original vol value=870 adjusted vol value:870
driver-btm-c5.c:13361:bitmain_c5_init: Chain[J11] orignal chain_voltage_pic=7 value=890
driver-btm-c5.c:13362:bitmain_c5_init: Chain[J11] original chain_voltage_value=870 adjusted chain_voltage_value:870, value=890
driver-btm-c5.c:13379:bitmain_c5_init: Chain[J11] will use backup chain_voltage_pic=870 [11]
driver-btm-c5.c:13389:bitmain_c5_init: Chain[J11] get working chain_voltage_pic=11
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[00] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[01] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[02] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[03] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[04] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[05] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[06] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[07] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[08] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[09] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[10] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[11] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[12] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[13] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[14] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[15] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[16] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J11] Aisc[17] original freq=575 adjusted freq:631
btm_adjust_hash.c:922:adjust_vol: Chain[J12] original vol value=870 adjusted vol value:870
driver-btm-c5.c:13361:bitmain_c5_init: Chain[J12] orignal chain_voltage_pic=7 value=890
driver-btm-c5.c:13362:bitmain_c5_init: Chain[J12] original chain_voltage_value=870 adjusted chain_voltage_value:870, value=890
driver-btm-c5.c:13379:bitmain_c5_init: Chain[J12] will use backup chain_voltage_pic=870 [11]
driver-btm-c5.c:13389:bitmain_c5_init: Chain[J12] get working chain_voltage_pic=11
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[00] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[01] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[02] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[03] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[04] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[05] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[06] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[07] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[08] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[09] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[10] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[11] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[12] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[13] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[14] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[15] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[16] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J12] Aisc[17] original freq=575 adjusted freq:631
btm_adjust_hash.c:922:adjust_vol: Chain[J13] original vol value=870 adjusted vol value:870
driver-btm-c5.c:13361:bitmain_c5_init: Chain[J13] orignal chain_voltage_pic=7 value=890
driver-btm-c5.c:13362:bitmain_c5_init: Chain[J13] original chain_voltage_value=870 adjusted chain_voltage_value:870, value=890
driver-btm-c5.c:13379:bitmain_c5_init: Chain[J13] will use backup chain_voltage_pic=870 [11]
driver-btm-c5.c:13389:bitmain_c5_init: Chain[J13] get working chain_voltage_pic=11
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[00] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[01] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[02] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[03] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[04] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[05] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[06] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[07] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[08] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[09] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[10] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[11] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[12] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[13] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[14] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[15] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[16] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J13] Aisc[17] original freq=575 adjusted freq:631
btm_adjust_hash.c:922:adjust_vol: Chain[J14] original vol value=870 adjusted vol value:870
driver-btm-c5.c:13361:bitmain_c5_init: Chain[J14] orignal chain_voltage_pic=7 value=890
driver-btm-c5.c:13362:bitmain_c5_init: Chain[J14] original chain_voltage_value=870 adjusted chain_voltage_value:870, value=890
driver-btm-c5.c:13379:bitmain_c5_init: Chain[J14] will use backup chain_voltage_pic=870 [11]
driver-btm-c5.c:13389:bitmain_c5_init: Chain[J14] get working chain_voltage_pic=11
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[00] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[01] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[02] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[03] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[04] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[05] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[06] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[07] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[08] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[09] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[10] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[11] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[12] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[13] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[14] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[15] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[16] original freq=575 adjusted freq:631
btm_adjust_hash.c:791:set_asic_freq: Chain[J14] Aisc[17] original freq=575 adjusted freq:631
driver-btm-c5.c:11856:T9_18_getASICnum: T9+ try get asic num for the 1 time
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J2] has 0 asic
driver-btm-c5.c:11856:T9_18_getASICnum: T9+ try get asic num for the 2 time
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J2] has 0 asic
driver-btm-c5.c:11856:T9_18_getASICnum: T9+ try get asic num for the 3 time
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J2] has 0 asic
driver-btm-c5.c:11856:T9_18_getASICnum: T9+ try get asic num for the 4 time
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J2] has 0 asic
driver-btm-c5.c:11856:T9_18_getASICnum: T9+ try get asic num for the 5 time
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J2] has 0 asic
driver-btm-c5.c:11856:T9_18_getASICnum: T9+ try get asic num for the 6 time
driver-btm-c5.c:11867:T9_18_getASICnum: Chain[J2] has 0 asic
driver-btm-c5.c:4486:set_frequency: Chain[J3] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J4] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J11] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J12] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J13] has core num in PIC
driver-btm-c5.c:4486:set_frequency: Chain[J14] has core num in PIC
driver-btm-c5.c:4583:set_frequency: miner total rate=7768GH/s ideal_total_hash_rate = 7500GH/s
driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[2]
driver-btm-c5.c:4610:set_frequency: Chain:2 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J3] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:2 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:4821:set_frequency: Chain:2 max freq=631
driver-btm-c5.c:4822:set_frequency: Chain:2 min freq=631

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[3]
driver-btm-c5.c:4610:set_frequency: Chain:3 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J4] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:3 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:4821:set_frequency: Chain:3 max freq=631
driver-btm-c5.c:4822:set_frequency: Chain:3 min freq=631

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[10]
driver-btm-c5.c:4610:set_frequency: Chain:10 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J11] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:10 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:4821:set_frequency: Chain:10 max freq=631
driver-btm-c5.c:4822:set_frequency: Chain:10 min freq=631

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[11]
driver-btm-c5.c:4610:set_frequency: Chain:11 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J12] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:11 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:4821:set_frequency: Chain:11 max freq=631
driver-btm-c5.c:4822:set_frequency: Chain:11 min freq=631

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[12]
driver-btm-c5.c:4610:set_frequency: Chain:12 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J13] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:12 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:4821:set_frequency: Chain:12 max freq=631
driver-btm-c5.c:4822:set_frequency: Chain:12 min freq=631

driver-btm-c5.c:4608:set_frequency: read PIC voltage=890 on chain[13]
driver-btm-c5.c:4610:set_frequency: Chain:13 chipnum=18
driver-btm-c5.c:4620:set_frequency: Chain[J14] voltage added=0.0V
driver-btm-c5.c:4681:set_frequency: Chain:13 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:4821:set_frequency: Chain:13 max freq=631
driver-btm-c5.c:4822:set_frequency: Chain:13 min freq=631


driver-btm-c5.c:4831:set_frequency: Miner fix freq ...
driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[2]
driver-btm-c5.c:4867:set_frequency: Chain:2 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J3] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:2 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:5122:set_frequency: Chain:2 max freq=631
driver-btm-c5.c:5123:set_frequency: Chain:2 min freq=631

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[3]
driver-btm-c5.c:4867:set_frequency: Chain:3 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J4] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:3 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:5122:set_frequency: Chain:3 max freq=631
driver-btm-c5.c:5123:set_frequency: Chain:3 min freq=631

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[10]
driver-btm-c5.c:4867:set_frequency: Chain:10 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J11] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:10 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:5122:set_frequency: Chain:10 max freq=631
driver-btm-c5.c:5123:set_frequency: Chain:10 min freq=631

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[11]
driver-btm-c5.c:4867:set_frequency: Chain:11 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J12] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:11 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:5122:set_frequency: Chain:11 max freq=631
driver-btm-c5.c:5123:set_frequency: Chain:11 min freq=631

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[12]
driver-btm-c5.c:4867:set_frequency: Chain:12 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J13] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:12 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:5122:set_frequency: Chain:12 max freq=631
driver-btm-c5.c:5123:set_frequency: Chain:12 min freq=631

driver-btm-c5.c:4866:set_frequency: read PIC voltage=890 on chain[13]
driver-btm-c5.c:4867:set_frequency: Chain:13 chipnum=18
driver-btm-c5.c:4876:set_frequency: Chain[J14] voltage added=0.0V
driver-btm-c5.c:4944:set_frequency: Chain:13 base freq=575
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631
driver-btm-c5.c:5122:set_frequency: Chain:13 max freq=631
driver-btm-c5.c:5123:set_frequency: Chain:13 min freq=631

driver-btm-c5.c:5131:set_frequency: max freq = 631
driver-btm-c5.c:4149:ProcessFixFreq: totalRate = 7768, fixed_totalRate = 7500
driver-btm-c5.c:9614:init_uart_baud: set baud=1
driver-btm-c5.c:6605:calibration_sensor_offset: Chain[J11] PIC temp offset: -1,-1,-1,-1,-1,-1,-1,-1,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6639:calibration_sensor_offset: chain[11] temp chip I2C addr=0x98
driver-btm-c5.c:6647:calibration_sensor_offset: chain[11] has no middle temp, use special fix mode.
driver-btm-c5.c:6777:calibration_sensor_offset: Warning: Chain[J11] has no temp offset in PIC! will fix it
driver-btm-c5.c:6901:calibration_sensor_offset: Chain[J11] use default temp chip[0]
driver-btm-c5.c:6331:do_calibration_sensor_offset: Chain[J11] try read temp chip[0] ID=41 (I2C addr=0x98)
driver-btm-c5.c:6396:do_calibration_sensor_offset: New offset Chain[11] chip[0] local:23 remote:17 offset:35
driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J11] chip[0] get middle temp offset=35 typeID=41
driver-btm-c5.c:6605:calibration_sensor_offset: Chain[J13] PIC temp offset: -1,-1,-1,-1,-1,-1,-1,-1,0,0,0,0,0,0,0,0,0,0,
driver-btm-c5.c:6639:calibration_sensor_offset: chain[13] temp chip I2C addr=0x98
driver-btm-c5.c:6647:calibration_sensor_offset: chain[13] has no middle temp, use special fix mode.
driver-btm-c5.c:6777:calibration_sensor_offset: Warning: Chain[J13] has no temp offset in PIC! will fix it
driver-btm-c5.c:6901:calibration_sensor_offset: Chain[J13] use default temp chip[0]
driver-btm-c5.c:6331:do_calibration_sensor_offset: Chain[J13] try read temp chip[0] ID=41 (I2C addr=0x98)
driver-btm-c5.c:6396:do_calibration_sensor_offset: New offset Chain[13] chip[0] local:22 remote:26 offset:25
driver-btm-c5.c:6906:calibration_sensor_offset: Chain[J13] chip[0] get middle temp offset=25 typeID=41
driver-btm-c5.c:13824:bitmain_c5_init: open core three times
driver-btm-c5.c:13868:bitmain_c5_init: open core on chain[2] [10] [11]...
driver-btm-c5.c:13824:bitmain_c5_init: open core three times
driver-btm-c5.c:13884:bitmain_c5_init: open core on chain[3] [12] [13]...
driver-btm-c5.c:13824:bitmain_c5_init: open core three times
driver-btm-c5.c:12129:set_working_voltage: setting to working voltage...
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 9 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[2] set voltage to 880
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 9 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[3] set voltage to 880
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 11 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[2] set voltage to 870
driver-btm-c5.c:2152:set_Voltage_S9_plus_plus_BM1387_54: set voltage 11 seccessful
driver-btm-c5.c:12109:slowly_downgrade_voltage_all_chain: chain[3] set voltage to 870
driver-btm-c5.c:14027:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=1501 total_tv_end_sys=1502
driver-btm-c5.c:10330:check_system_work: restartNum = 2 , auto-reinit enabled...
util.c:3207:initiate_stratum: mining.subscribe:{"id": 0, "method": "mining.subscribe", "params": ["bmminer/2.0.0/Antminer T9+/10500"]}
driver-btm-c5.c:8738:read_temp_func: bring_up_pcb_temp = 40
driver-btm-c5.c:10461:check_system_work: checking hash again
driver-btm-c5.c:9897:if_avg_hash_ok: avg hash rate = 7581.478697, ideal hash rate = 7500
driver-btm-c5.c:10464:check_system_work: hash rate is ok now
do read_temp_func once...

get RT hashrate from Chain[2]: (asic index start from 1-18)
Asic[01]=74.8760 Asic[02]=73.1820 Asic[03]=72.5950 Asic[04]=73.0140 Asic[05]=72.2760 Asic[06]=65.4470 Asic[07]=76.1510 Asic[08]=77.8630
Asic[09]=73.8020 Asic[10]=73.4000 Asic[11]=72.9800 Asic[12]=74.8090 Asic[13]=70.0950 Asic[14]=74.4570 Asic[15]=71.4200 Asic[16]=73.9030
Asic[17]=74.4900 Asic[18]=68.1320

get RT hashrate from Chain[3]: (asic index start from 1-18)
Asic[01]=74.2890 Asic[02]=69.0710 Asic[03]=72.8290 Asic[04]=66.2190 Asic[05]=75.0270 Asic[06]=68.6020 Asic[07]=73.3330 Asic[08]=66.7900
Asic[09]=65.6660 Asic[10]=67.8300 Asic[11]=71.7560 Asic[12]=69.7090 Asic[13]=77.4770 Asic[14]=70.5640 Asic[15]=68.4840 Asic[16]=71.4540
Asic[17]=76.9730 Asic[18]=65.7660

get RT hashrate from Chain[10]: (asic index start from 1-18)
Asic[01]=72.8130 Asic[02]=66.6890 Asic[03]=71.1850 Asic[04]=65.5310 Asic[05]=70.4810 Asic[06]=72.1420 Asic[07]=73.9370 Asic[08]=69.6080
Asic[09]=75.7150 Asic[10]=70.8160 Asic[11]=68.7020 Asic[12]=74.8760 Asic[13]=72.5780 Asic[14]=77.7120 Asic[15]=73.9530 Asic[16]=70.9500
Asic[17]=73.9700 Asic[18]=70.1790

get RT hashrate from Chain[11]: (asic index start from 1-18)
Asic[01]=71.8560 Asic[02]=73.6180 Asic[03]=72.8970 Asic[04]=67.7120 Asic[05]=67.9640 Asic[06]=68.2490 Asic[07]=71.8060 Asic[08]=72.2090
Asic[09]=73.1650 Asic[10]=80.0270 Asic[11]=66.1860 Asic[12]=74.1550 Asic[13]=75.9670 Asic[14]=65.4140 Asic[15]=72.2930 Asic[16]=66.2020
Asic[17]=69.1720 Asic[18]=71.9070

get RT hashrate from Chain[12]: (asic index start from 1-18)
Asic[01]=68.2160 Asic[02]=73.3660 Asic[03]=69.0880 Asic[04]=69.3230 Asic[05]=74.4230 Asic[06]=69.4400 Asic[07]=70.5810 Asic[08]=72.6280
Asic[09]=72.4270 Asic[10]=66.0680 Asic[11]=69.5240 Asic[12]=75.6480 Asic[13]=68.2660 Asic[14]=74.9770 Asic[15]=73.3490 Asic[16]=72.6450
Asic[17]=68.0810 Asic[18]=68.9200

get RT hashrate from Chain[13]: (asic index start from 1-18)
Asic[01]=72.7620 Asic[02]=66.7060 Asic[03]=70.2460 Asic[04]=71.4370 Asic[05]=72.3260 Asic[06]=67.9300 Asic[07]=72.5110 Asic[08]=74.9770
Asic[09]=77.1080 Asic[10]=75.2960 Asic[11]=75.1610 Asic[12]=70.3970 Asic[13]=69.8260 Asic[14]=71.5880 Asic[15]=73.4840 Asic[16]=69.6750
Asic[17]=73.0140 Asic[18]=66.9410
Check Chain[J3] ASIC RT error: (asic index start from 1-18)
Check Chain[J4] ASIC RT error: (asic index start from 1-18)
Check Chain[J11] ASIC RT error: (asic index start from 1-18)
Check Chain[J12] ASIC RT error: (asic index start from 1-18)
Check Chain[J13] ASIC RT error: (asic index start from 1-18)
Check Chain[J14] ASIC RT error: (asic index start from 1-18)
Done check_asic_reg
Chain[10] Chip[1] junction temperature=76
Special fix Chain[10] Chip[1] middle Temp = 77
Done read temp on Chain[10]
Chain[12] Chip[0] pcb temperature=65
Chain[12] Chip[1] junction temperature=72
Special fix Chain[12] Chip[1] middle Temp = 80
Done read temp on Chain[12]
Max pcb temp : 65
Read temp failed, set fixed full fan speed
FAN PWM: 100
read_temp_func Done!
CRC error counter=32810
Bitcoin Forum>Bitcoin>Mining>Mining support
Jump to: