NVM GOT it.
Restarted computer!
Thanks for all your help!
If you have any setting suggestions please let me know.
Thanks again!
Topic: Antminer U2 going idle (Read 866 times)
Thank you very much I switched from using bfgminer to cgminer and it worked. I am not sure what the problem was at all(I did have to do zadig). I have one more question, like I said earlier I have two miners and they are both currently plugged in is this the correct output? Should I be seeing ANU0 and also ANU1. I ask because when I was using bfgminer I was seeing AMU0 and AMU1.
https://i.imgur.com/mJ3cJig.png
If so is there as special command that I should be using to start up cgminer to use all miners? I currently am using this which I found online; if you have any other recommendations let me know. Thanks for your time and help.
cgminer --anu-freq 200 -o stratum+tcp://stratum.bitcoin.cz:3333 -u cogle.first -p 123
Edit: Current Devices
https://i.imgur.com/3wumLTK.png?1
https://i.imgur.com/mJ3cJig.png
If so is there as special command that I should be using to start up cgminer to use all miners? I currently am using this which I found online; if you have any other recommendations let me know. Thanks for your time and help.
cgminer --anu-freq 200 -o stratum+tcp://stratum.bitcoin.cz:3333 -u cogle.first -p 123
Edit: Current Devices
https://i.imgur.com/3wumLTK.png?1
what do they look like in
windows control panel devices and printers?
here is my 1 U2
now I went to ck's cgminer 4.9.2
I used zadig to load and replace the silabs driver
I used cgminer cg 4.9.2 to run
I use a powered usb2 hub
windows control panel devices and printers?
here is my 1 U2
now I went to ck's cgminer 4.9.2
I used zadig to load and replace the silabs driver
I used cgminer cg 4.9.2 to run
I use a powered usb2 hub
Hello I recently bought two Antminer U2 USB sticks, unfortunately I have not been able to get either of them to work. Every time I attempt to connect my sticks to a pool using bfgminer I get an output like so
[2015-08-09 18:53:16] Started bfgminer 5.2.0
[2015-08-09 18:53:17] Probing for an alive pool
[2015-08-09 18:53:17] Pool 0 stratum+tcp://stratum.bitcoin.cz:3333 alive
[2015-08-09 18:53:17] Pool 0 is hiding block contents from us
[2015-08-09 18:53:17] Network difficulty changed to 52.7G (377.2Ph)
[2015-08-09 18:53:17] Stratum from pool 0 detected new block
[2015-08-09 18:54:26] AMU 0: Idle for more than 60 seconds, declaring SICK!
[2015-08-09 18:54:27] AMU 1: Idle for more than 60 seconds, declaring SICK!
[2015-08-09 18:57:54] Stratum from pool 0 detected new block
I have installed these drivers http://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx and since I have a Windows 8 clicked the first link.
I am also sure that I have put them into the USB 2.0 slot. Does anybody have any idea as to what might be occurring here. Thanks.
[2015-08-09 18:53:16] Started bfgminer 5.2.0
[2015-08-09 18:53:17] Probing for an alive pool
[2015-08-09 18:53:17] Pool 0 stratum+tcp://stratum.bitcoin.cz:3333 alive
[2015-08-09 18:53:17] Pool 0 is hiding block contents from us
[2015-08-09 18:53:17] Network difficulty changed to 52.7G (377.2Ph)
[2015-08-09 18:53:17] Stratum from pool 0 detected new block
[2015-08-09 18:54:26] AMU 0: Idle for more than 60 seconds, declaring SICK!
[2015-08-09 18:54:27] AMU 1: Idle for more than 60 seconds, declaring SICK!
[2015-08-09 18:57:54] Stratum from pool 0 detected new block
I have installed these drivers http://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx and since I have a Windows 8 clicked the first link.
I am also sure that I have put them into the USB 2.0 slot. Does anybody have any idea as to what might be occurring here. Thanks.
Jump to: