ASIC codes on blades are not Ok. | Bitcointalksearch.org

tim-bc

full member

Activity: 538

Merit: 175

Make sure your PSU is good and is running on at least 200V rather than 110. Otherwise, it's definitely an issue with the boards. Maybe since it's new you could take them up on the warranty?

scoxdo

newbie

Activity: 4

Merit: 0

I have already done it and nothing changes. Sad

Thanks for the response buddy.

mikeywith

legendary

Activity: 2436

Merit: 6643

be constructive or S.T.F.U

Quote from: scoxdo on June 30, 2019, 01:35:53 PM

Since this is a new miner, i am betting on the PSU , you need to try another working PSU.

The probability of these hash boards being burnt is still there tho, and usually there isn't much to do about them, but before going any further i would test the gear with a working PSU.

scoxdo

newbie

Activity: 4

Merit: 0

Quote from: ?? on ??

Thanks a lot for your responses and im sorry for the lack of knowledge on forums format; ill try my best to learn on this.

Im going to input more info in hours so maybe i can get more help.

Once more, thank you guys for the help you are giving and for taking the time to answer.

Ok, the info u wanted me to add:

Model: Antminer S9
New or used: New
PSU Model: APW3++-12-1600 A3
Temperatures: ~80 ºC

Screenshot: https://imgur.com/nJR6yaj

Thanks a lot for the help!!

mikeywith

legendary

Activity: 2436

Merit: 6643

be constructive or S.T.F.U

It is all in the kernel log.

Code:

J7 has 0 asics

This means the board which data cable goes to j7 (usually middle) is toasted.

Code:

J8 has 23 asics

A good hash board must have 63 asics in order for it to provide 1/3 of the total hash rate, so with those a few asics, this is all you going to get.

You should try Bitmaxz suggestions, but your chances are slim to nothing.

Also you have a missing board (j6) usually the one the hand right side when you looking at the miner from the back side, it is either the data cable or 6pin not plugged right.

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

The above post is right you should use the code button # you can find it while you are making a message here on the forum.
And Agree about more additional info for both "miner's status" and "PSU and outlet voltage(110v or 240v)"

- Try to hard reset the miner you can follow the guide from here How to reset miner to factory settings
Ignore the 2nd method then set the pool again(Make sure no spaces when pasting the pool) and then test. If not work try to use ping button under the network then diagnostic to check if the miner is receiving data to the internet. if the ping is fine then do the next step below.

- Can you do some test? Check this guide: Test hash board one by one
After that, if all hashboard is fine when running it one by one possible the PSU not giving enough power.

- Check the PSU if it gives you enough power If you have multi-tester you can test the output voltage it should be 12v.

NotFuzzyWarm

legendary

Activity: 3822

Merit: 2703

Evil beware: We have waffles!

Quote from: scoxdo on June 28, 2019, 12:45:59 PM

Thanks so much for replying, i deeply appreciate any help you could give me on this. Well, as u were asking for, ill post the kernel log:

Then, after ~3 min the antminer restarts.

Thanks for reading and thanks in advance for any help i can get from here. Have a nice day.

Please learn how to use the Forum formatting options...
By using the CODE tag which looks like this #, that text wall is reduced to

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc:

    0
    1 

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06da8ac   (6987 kB)
[    0.000000]       .init : 0xc06db000 - 0xc070e380   ( 205 kB)
[    0.000000]       .data : 0xc0710000 - 0xc0757138   ( 285 kB)
[    0.000000]        .bss : 0xc0757144 - 0xc0797bfc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]    Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000]    RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000309] ps7-ttc #0 at df804000, irq=43
[    0.000625] Console: colour dummy device 80x30
[    0.000654] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040204] pid_max: default: 32768 minimum: 301
[    0.040420] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040441] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042641] CPU: Testing write buffer coherency: ok
[    0.042976] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043034] Setting up static identity map for 0x4cb118 - 0x4cb170
[    0.043260] L310 cache controller enabled
[    0.043280] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121031] CPU1: Booted secondary processor
[    0.210225] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210355] Brought up 2 CPUs
[    0.210374] SMP: Total of 2 processors activated.
[    0.210383] CPU: All CPU(s) started in SVC mode.
[    0.211051] devtmpfs: initialized
[    0.213513] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214725] regulator-dummy: no parameters
[    0.222426] NET: Registered protocol family 16
[    0.224659] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226957] cpuidle: using governor ladder
[    0.226972] cpuidle: using governor menu
[    0.234425] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235952] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235966] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.236082] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.257572] bio: create slab  at 0
[    0.258977] vgaarb: loaded
[    0.259675] SCSI subsystem initialized
[    0.260746] usbcore: registered new interface driver usbfs
[    0.260918] usbcore: registered new interface driver hub
[    0.261406] usbcore: registered new device driver usb
[    0.261938] media: Linux media interface: v0.10
[    0.262096] Linux video capture interface: v2.00
[    0.262341] pps_core: LinuxPPS API ver. 1 registered
[    0.262353] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.262474] PTP clock support registered
[    0.262834] EDAC MC: Ver: 3.0.0
[    0.264035] Advanced Linux Sound Architecture Driver Initialized.
[    0.266903] DMA-API: preallocated 4096 debug entries
[    0.266917] DMA-API: debugging enabled by kernel config
[    0.266993] Switched to clocksource arm_global_timer
[    0.287714] NET: Registered protocol family 2
[    0.288374] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.288431] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.288516] TCP: Hash tables configured (established 4096 bind 4096)
[    0.288560] TCP: reno registered
[    0.288578] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.288609] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.288851] NET: Registered protocol family 1
[    0.289186] RPC: Registered named UNIX socket transport module.
[    0.289198] RPC: Registered udp transport module.
[    0.289207] RPC: Registered tcp transport module.
[    0.289215] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.289228] PCI: CLS 0 bytes, default 64
[    0.289658] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291662] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.293796] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293978] msgmni has been set to 967
[    0.294742] io scheduler noop registered
[    0.294755] io scheduler deadline registered
[    0.294794] io scheduler cfq registered (default)
[    0.306564] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.306585] dma-pl330 f8003000.ps7-dma:    DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.429800] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.997066] console [ttyPS0] enabled
[    1.001320] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.008968] [drm] Initialized drm 1.1.0 20060810
[    1.026208] brd: module loaded
[    1.035650] loop: module loaded
[    1.045150] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.051139] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.058919] libphy: XEMACPS mii bus: probed
[    1.063287] ------------- phy_id = 0x3625e62
[    1.068193] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.076783] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.083435] ehci-pci: EHCI PCI platform driver
[    1.090706] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.097584] usbcore: registered new interface driver usb-storage
[    1.104412] mousedev: PS/2 mouse device common for all mice
[    1.110533] i2c /dev entries driver
[    1.117457] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.122938] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.128872] Xilinx Zynq CpuIdle Driver started
[    1.133724] sdhci: Secure Digital Host Controller Interface driver
[    1.139927] sdhci: Copyright(c) Pierre Ossman
[    1.144201] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.151023] mmc0: no vqmmc regulator found
[    1.155037] mmc0: no vmmc regulator found
[    1.197021] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.205710] usbcore: registered new interface driver usbhid
[    1.211210] usbhid: USB HID core driver
[    1.215927] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.222224] nand: Micron MT29F2G08ABAEAWP
[    1.226187] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.232126] Bad block table found at page 131008, version 0x01
[    1.238352] Bad block table found at page 130944, version 0x01
[    1.244406] 3 ofpart partitions found on MTD device pl353-nand
[    1.250184] Creating 3 MTD partitions on "pl353-nand":
[    1.255278] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.263358] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.270676] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.281479] TCP: cubic registered
[    1.284717] NET: Registered protocol family 17
[    1.289435] Registering SWP/SWPB emulation handler
[    1.295340] regulator-dummy: disabling
[    1.299688] UBI: attaching mtd1 to ubi0
[    1.825967] UBI: scanning is finished
[    1.837667] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.844723] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.851510] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.858195] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.865033] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.871043] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.878154] UBI: max/mean erase counter: 82/49, WL threshold: 4096, image sequence number: 1392745112
[    1.887358] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.896556] UBI: background thread "ubi_bgt0d" started, PID 1084
[    1.896561] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.900571] ALSA device list:
[    1.900574]   No soundcards found.
[    1.916917] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[    1.945953] UBIFS: recovery needed
[    2.481635] UBIFS: recovery completed
[    2.485313] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.491263] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.500368] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.510256] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.515286] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 7F557ABA-3B20-41F1-A042-3AAD483DA050, small LPT model
[    2.526596] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.533788] devtmpfs: mounted
[    2.536897] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[    3.388688] random: dd urandom read with 1 bits of entropy available
[    3.777029]
[    3.777029] bcm54xx_config_init
[    4.387040]
[    4.387040] bcm54xx_config_init
[    7.387859] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.393949] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   19.490734] In axi fpga driver!
[   19.493806] request_mem_region OK!
[   19.497228] AXI fpga dev virtual address is 0xdf9fe000
[   19.502304] *base_vir_addr = 0x8c510
[   19.516981] In fpga mem driver!
[   19.520134] request_mem_region OK!
[   19.523687] fpga mem virtual address is 0xe2000000
[   20.326415]
[   20.326415] bcm54xx_config_init
[   20.956352]
[   20.956352] bcm54xx_config_init
[   23.956913] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   23.962929] xemacps e000b000.ps7-ethernet: link up (100/FULL)
main.c:13927: log_level = 4
main.c:13954: This is XILINX board. Totalram:       507486208
main.c:13966: Detect 512MB control board of XILINX
driver-bitmain.c:1003: forceFreq=-1 forceFlag=0
main.c:8434: DETECT HW version=0008c510
main.c:13999: miner ID : 80242d292f90481c
main.c:14024: Miner Type = S9
main.c:14036: AsicType = 1387
main.c:14039: real AsicNum = 63
main.c:14132: use critical mode to search freq...
driver-bitmain.c:2401: get PLUG ON=0x000000c0
driver-bitmain.c:2471: Find hashboard on Chain[6]
driver-bitmain.c:2471: Find hashboard on Chain[7]
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
main.c:2164: Check chain[6] PIC fw version=0x03
main.c:2164: Check chain[7] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[6] has freq in PIC and will jump over...
main.c:8965: Chain[6] has core num in PIC
main.c:8975: Chain[6] ASIC[25] has core num=1
main.c:8975: Chain[6] ASIC[42] has core num=15
main.c:2164: Check chain[6] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[7] has freq in PIC and will jump over...
main.c:8965: Chain[7] has core num in PIC
main.c:2164: Check chain[7] PIC fw version=0x03
main.c:9039: get PIC voltage=6 on chain[6], value=940
main.c:9039: get PIC voltage=6 on chain[7], value=940
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:9205: chain[6] temp offset record: 62,-4,0,0,0,0,33,0
main.c:9222: chain[6] temp chip I2C addr=0x98
main.c:9205: chain[7] temp offset record: 62,-4,0,0,0,0,33,0
main.c:9222: chain[7] temp chip I2C addr=0x98
main.c:13838: total_exist_chain_num = 2
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:9456: CRC error counter=0
main.c:9471: set command mode to VIL
main.c:9543:
--- check asic number
main.c:9640: After Get ASIC NUM CRC error counter=0
main.c:9663: set_baud=0
main.c:10588: The min freq=700
main.c:10590: set real timeout 52, need sleep=379392
main.c:12720: After TEST CRC error counter=0
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:14167: search freq for 1 times, completed chain = 2, total chain num = 2
board_frq_tuning.c:549: single_board_frq_tuning enter
board_frq_tuning.c:550: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:132: force_freq not set, don't need tuning
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:14559: restart Miner chance num=2
main.c:14599: waiting for receive_func to exit!
main.c:14613: waiting for pic heart to exit!
main.c:13809: bmminer not found= 1374 root       0:00 grep bmminer

main.c:14657: bmminer not found, restart bmminer ...
This is the first time running after searching freq!
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Tue Jul 17 18:03:36 CST 2018 type: Antminer S9i
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 80242d292f90481c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=30600
get fan[2] speed=30600
get fan[2] speed=30600
get fan[5] speed=4560
get fan[2] speed=30600
get fan[5] speed=4560
get fan[2] speed=30600
get fan[5] speed=4560
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:14951:bitmain_c5_init: last_freq: 0x00 0x7d 0x0f 0x4c 0x0c 0x4c 0x04 0x4c 0x0c 0x4c 0x00 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x01 0x4c 0x01 0x4c 0x0f 0x4c 0x0f 0x4c 0x0f 0x4c 0x0f 0x4c 0x05 0x4c 0x07 0x4c 0x23 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:14951:bitmain_c5_init: last_freq: 0x00 0x7d 0x0f 0x47 0x0c 0x47 0x04 0x47 0x07 0x47 0x00 0x47 0x03 0x47 0x03 0x47 0x03 0x47 0x03 0x47 0x03 0x47 0x03 0x47 0x01 0x47 0x01 0x47 0x0f 0x47 0x0f 0x47 0x0f 0x47 0x0f 0x47 0x05 0x47 0x09 0x47 0x23 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=890
Check chain[7] PIC fw version=0x03
driver-btm-c5.c:14014:init_exist_chain_table: total_exist_chain_num = 2
Chain[J7] orignal chain_voltage_pic=6 value=940
Chain[J7] will use backup chain_voltage_pic=870 [125]
Chain[J7] get working chain_voltage_pic=125
Chain[J8] orignal chain_voltage_pic=6 value=940
Chain[J8] will use backup chain_voltage_pic=890 [91]
Chain[J8] get working chain_voltage_pic=91
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
driver-btm-c5.c:6334:set_frequency: Chain[J7] has core num in PIC
driver-btm-c5.c:6344:set_frequency: Chain[J7] ASIC[25] has core num=1
driver-btm-c5.c:6344:set_frequency: Chain[J7] ASIC[42] has core num=15
driver-btm-c5.c:6334:set_frequency: Chain[J8] has core num in PIC
driver-btm-c5.c:6374:set_frequency: miner total rate=9210GH/s ideal_total_hash_rate = 9000GH/s
driver-btm-c5.c:6399:set_frequency: read PIC voltage=940 on chain[6]
driver-btm-c5.c:6401:set_frequency: Chain:6 chipnum=29
driver-btm-c5.c:6418:set_frequency: Chain[J7] voltage added=0.0V
driver-btm-c5.c:6530:set_frequency: Chain:6 temp offset=-4
driver-btm-c5.c:6535:set_frequency: Chain:6 base freq=662
Asic[ 0]:662 Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:662 Asic[ 6]:662 Asic[ 7]:662
Asic[ 8]:662 Asic[ 9]:662 Asic[10]:662 Asic[11]:662 Asic[12]:662 Asic[13]:662 Asic[14]:662 Asic[15]:662
Asic[16]:662 Asic[17]:662 Asic[18]:662 Asic[19]:662 Asic[20]:662 Asic[21]:662 Asic[22]:662 Asic[23]:662
Asic[24]:662 Asic[25]:662 Asic[26]:662 Asic[27]:662 Asic[28]:662
driver-btm-c5.c:6571:set_frequency: Chain:6 max freq=662
driver-btm-c5.c:6572:set_frequency: Chain:6 min freq=662

driver-btm-c5.c:6399:set_frequency: read PIC voltage=940 on chain[7]
driver-btm-c5.c:6401:set_frequency: Chain:7 chipnum=27
driver-btm-c5.c:6418:set_frequency: Chain[J8] voltage added=0.0V
driver-btm-c5.c:6530:set_frequency: Chain:7 temp offset=-4
driver-btm-c5.c:6535:set_frequency: Chain:7 base freq=631
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631
Asic[24]:631 Asic[25]:631 Asic[26]:631
driver-btm-c5.c:6571:set_frequency: Chain:7 max freq=631
driver-btm-c5.c:6572:set_frequency: Chain:7 min freq=631


driver-btm-c5.c:6581:set_frequency: Miner fix freq ...
driver-btm-c5.c:6616:set_frequency: read PIC voltage=940 on chain[6]
driver-btm-c5.c:6617:set_frequency: Chain:6 chipnum=29
driver-btm-c5.c:6636:set_frequency: Chain[J7] voltage added=0.0V
driver-btm-c5.c:6778:set_frequency: Chain:6 temp offset=-4
driver-btm-c5.c:6783:set_frequency: Chain:6 base freq=662
Asic[ 0]:662 Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:662 Asic[ 6]:662 Asic[ 7]:662
Asic[ 8]:662 Asic[ 9]:662 Asic[10]:662 Asic[11]:662 Asic[12]:662 Asic[13]:662 Asic[14]:662 Asic[15]:662
Asic[16]:662 Asic[17]:662 Asic[18]:662 Asic[19]:662 Asic[20]:662 Asic[21]:662 Asic[22]:662 Asic[23]:662
Asic[24]:662 Asic[25]:662 Asic[26]:662 Asic[27]:662 Asic[28]:662
driver-btm-c5.c:6830:set_frequency: Chain:6 max freq=662
driver-btm-c5.c:6831:set_frequency: Chain:6 min freq=662

driver-btm-c5.c:6616:set_frequency: read PIC voltage=940 on chain[7]
driver-btm-c5.c:6617:set_frequency: Chain:7 chipnum=27
driver-btm-c5.c:6636:set_frequency: Chain[J8] voltage added=0.0V
driver-btm-c5.c:6778:set_frequency: Chain:7 temp offset=-4
driver-btm-c5.c:6783:set_frequency: Chain:7 base freq=631
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631
Asic[16]:631 Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631
Asic[24]:631 Asic[25]:631 Asic[26]:631
driver-btm-c5.c:6830:set_frequency: Chain:7 max freq=631
driver-btm-c5.c:6831:set_frequency: Chain:7 min freq=631

driver-btm-c5.c:6839:set_frequency: max freq = 662
driver-btm-c5.c:5954:ProcessFixFreq: totalRate = 9210, fixed_totalRate = 9000
set baud=1
driver-btm-c5.c:13950:set_working_voltage: chain[6] last_testpatten_highest_pcb_temp = 0
driver-btm-c5.c:13907:slowly_downgrade_voltage: chain[6] current_voltage_value = 940
driver-btm-c5.c:13908:slowly_downgrade_voltage: chain[6] target_voltage_value = 870
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 930
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 920
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 910
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 900
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 890
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 880
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 870
driver-btm-c5.c:13935:slowly_downgrade_voltage: chain[6] set working voltage to 870
driver-btm-c5.c:13950:set_working_voltage: chain[7] last_testpatten_highest_pcb_temp = 0
driver-btm-c5.c:13907:slowly_downgrade_voltage: chain[7] current_voltage_value = 940
driver-btm-c5.c:13908:slowly_downgrade_voltage: chain[7] target_voltage_value = 890
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 930
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 920
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 910
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 900
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 890
driver-btm-c5.c:13935:slowly_downgrade_voltage: chain[7] set working voltage to 890
driver-btm-c5.c:15764:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=197 total_tv_end_sys=198
restartNum = 2 , auto-reinit enabled...
driver-btm-c5.c:10467:read_temp_func: last_testpatten_highest_pcb_temp = -100
do read_temp_func once...

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=0.00000
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=805.306 Asic[08]=0.00000
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Asic[29]=4503599.627000
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Asic[07]=805.306000
Done check_asic_reg
Done read temp on Chain[6]
Done read temp on Chain[7]
Max pcb temp : -100
set FAN speed according to: temp_highest=-100 temp_top1[PWM_T]=-100 temp_top1[TEMP_POS_LOCAL]=-100 temp_change=0 fix_fan_steps=0
FAN PWM: 0
read_temp_func Done!
CRC error counter=1290

Safe bet a mod will do that if you do not edit the post...
Oh - and when asking help questions a LOT more info would be nice such as:
Make and model of miner?
Bought new or used?
PSU used and what your AC power is?
Temps where the miners are?
Screen shot of the miner status page.

For the most part the kernal logs are useless...

scoxdo

newbie

Activity: 4

Merit: 0

Thanks so much for replying, i deeply appreciate any help you could give me on this. Well, as u were asking for, ill post the kernel log:

Code:

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06da8ac   (6987 kB)
[    0.000000]       .init : 0xc06db000 - 0xc070e380   ( 205 kB)
[    0.000000]       .data : 0xc0710000 - 0xc0757138   ( 285 kB)
[    0.000000]        .bss : 0xc0757144 - 0xc0797bfc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000309] ps7-ttc #0 at df804000, irq=43
[    0.000625] Console: colour dummy device 80x30
[    0.000654] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040204] pid_max: default: 32768 minimum: 301
[    0.040420] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040441] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042641] CPU: Testing write buffer coherency: ok
[    0.042976] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.043034] Setting up static identity map for 0x4cb118 - 0x4cb170
[    0.043260] L310 cache controller enabled
[    0.043280] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.121031] CPU1: Booted secondary processor
[    0.210225] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210355] Brought up 2 CPUs
[    0.210374] SMP: Total of 2 processors activated.
[    0.210383] CPU: All CPU(s) started in SVC mode.
[    0.211051] devtmpfs: initialized
[    0.213513] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214725] regulator-dummy: no parameters
[    0.222426] NET: Registered protocol family 16
[    0.224659] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226957] cpuidle: using governor ladder
[    0.226972] cpuidle: using governor menu
[    0.234425] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235952] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235966] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.236082] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.257572] bio: create slab  at 0
[    0.258977] vgaarb: loaded
[    0.259675] SCSI subsystem initialized
[    0.260746] usbcore: registered new interface driver usbfs
[    0.260918] usbcore: registered new interface driver hub
[    0.261406] usbcore: registered new device driver usb
[    0.261938] media: Linux media interface: v0.10
[    0.262096] Linux video capture interface: v2.00
[    0.262341] pps_core: LinuxPPS API ver. 1 registered
[    0.262353] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti 
[    0.262474] PTP clock support registered
[    0.262834] EDAC MC: Ver: 3.0.0
[    0.264035] Advanced Linux Sound Architecture Driver Initialized.
[    0.266903] DMA-API: preallocated 4096 debug entries
[    0.266917] DMA-API: debugging enabled by kernel config
[    0.266993] Switched to clocksource arm_global_timer
[    0.287714] NET: Registered protocol family 2
[    0.288374] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.288431] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.288516] TCP: Hash tables configured (established 4096 bind 4096)
[    0.288560] TCP: reno registered
[    0.288578] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.288609] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.288851] NET: Registered protocol family 1
[    0.289186] RPC: Registered named UNIX socket transport module.
[    0.289198] RPC: Registered udp transport module.
[    0.289207] RPC: Registered tcp transport module.
[    0.289215] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.289228] PCI: CLS 0 bytes, default 64
[    0.289658] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.291662] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.293796] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.293978] msgmni has been set to 967
[    0.294742] io scheduler noop registered
[    0.294755] io scheduler deadline registered
[    0.294794] io scheduler cfq registered (default)
[    0.306564] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.306585] dma-pl330 f8003000.ps7-dma: 	DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.429800] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.997066] console [ttyPS0] enabled
[    1.001320] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.008968] [drm] Initialized drm 1.1.0 20060810
[    1.026208] brd: module loaded
[    1.035650] loop: module loaded
[    1.045150] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.051139] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.058919] libphy: XEMACPS mii bus: probed
[    1.063287] ------------- phy_id = 0x3625e62
[    1.068193] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.076783] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.083435] ehci-pci: EHCI PCI platform driver
[    1.090706] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.097584] usbcore: registered new interface driver usb-storage
[    1.104412] mousedev: PS/2 mouse device common for all mice
[    1.110533] i2c /dev entries driver
[    1.117457] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.122938] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.128872] Xilinx Zynq CpuIdle Driver started
[    1.133724] sdhci: Secure Digital Host Controller Interface driver
[    1.139927] sdhci: Copyright(c) Pierre Ossman
[    1.144201] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.151023] mmc0: no vqmmc regulator found
[    1.155037] mmc0: no vmmc regulator found
[    1.197021] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.205710] usbcore: registered new interface driver usbhid
[    1.211210] usbhid: USB HID core driver
[    1.215927] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.222224] nand: Micron MT29F2G08ABAEAWP
[    1.226187] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.232126] Bad block table found at page 131008, version 0x01
[    1.238352] Bad block table found at page 130944, version 0x01
[    1.244406] 3 ofpart partitions found on MTD device pl353-nand
[    1.250184] Creating 3 MTD partitions on "pl353-nand":
[    1.255278] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.263358] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.270676] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.281479] TCP: cubic registered
[    1.284717] NET: Registered protocol family 17
[    1.289435] Registering SWP/SWPB emulation handler
[    1.295340] regulator-dummy: disabling
[    1.299688] UBI: attaching mtd1 to ubi0
[    1.825967] UBI: scanning is finished
[    1.837667] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.844723] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.851510] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.858195] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.865033] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.871043] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.878154] UBI: max/mean erase counter: 82/49, WL threshold: 4096, image sequence number: 1392745112
[    1.887358] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.896556] UBI: background thread "ubi_bgt0d" started, PID 1084
[    1.896561] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.900571] ALSA device list:
[    1.900574]   No soundcards found.
[    1.916917] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[    1.945953] UBIFS: recovery needed
[    2.481635] UBIFS: recovery completed
[    2.485313] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    2.491263] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    2.500368] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.510256] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.515286] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 7F557ABA-3B20-41F1-A042-3AAD483DA050, small LPT model
[    2.526596] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.533788] devtmpfs: mounted
[    2.536897] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[    3.388688] random: dd urandom read with 1 bits of entropy available
[    3.777029] 
[    3.777029] bcm54xx_config_init
[    4.387040] 
[    4.387040] bcm54xx_config_init
[    7.387859] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    7.393949] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   19.490734] In axi fpga driver!
[   19.493806] request_mem_region OK!
[   19.497228] AXI fpga dev virtual address is 0xdf9fe000
[   19.502304] *base_vir_addr = 0x8c510
[   19.516981] In fpga mem driver!
[   19.520134] request_mem_region OK!
[   19.523687] fpga mem virtual address is 0xe2000000
[   20.326415] 
[   20.326415] bcm54xx_config_init
[   20.956352] 
[   20.956352] bcm54xx_config_init
[   23.956913] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   23.962929] xemacps e000b000.ps7-ethernet: link up (100/FULL)
main.c:13927: log_level = 4
main.c:13954: This is XILINX board. Totalram:       507486208
main.c:13966: Detect 512MB control board of XILINX
driver-bitmain.c:1003: forceFreq=-1 forceFlag=0
main.c:8434: DETECT HW version=0008c510
main.c:13999: miner ID : 80242d292f90481c
main.c:14024: Miner Type = S9
main.c:14036: AsicType = 1387
main.c:14039: real AsicNum = 63
main.c:14132: use critical mode to search freq...
driver-bitmain.c:2401: get PLUG ON=0x000000c0
driver-bitmain.c:2471: Find hashboard on Chain[6]
driver-bitmain.c:2471: Find hashboard on Chain[7]
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
main.c:2164: Check chain[6] PIC fw version=0x03
main.c:2164: Check chain[7] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[6] has freq in PIC and will jump over...
main.c:8965: Chain[6] has core num in PIC
main.c:8975: Chain[6] ASIC[25] has core num=1
main.c:8975: Chain[6] ASIC[42] has core num=15
main.c:2164: Check chain[6] PIC fw version=0x03
main.c:8799: read pic freq and badcore num...
main.c:8820: chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
main.c:8862: has freq in PIC, will disable freq setting.
main.c:8961: chain[7] has freq in PIC and will jump over...
main.c:8965: Chain[7] has core num in PIC
main.c:2164: Check chain[7] PIC fw version=0x03
main.c:9039: get PIC voltage=6 on chain[6], value=940
main.c:9039: get PIC voltage=6 on chain[7], value=940
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:9205: chain[6] temp offset record: 62,-4,0,0,0,0,33,0
main.c:9222: chain[6] temp chip I2C addr=0x98
main.c:9205: chain[7] temp offset record: 62,-4,0,0,0,0,33,0
main.c:9222: chain[7] temp chip I2C addr=0x98
main.c:13838: total_exist_chain_num = 2
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:9456: CRC error counter=0
main.c:9471: set command mode to VIL
main.c:9543: 
--- check asic number
main.c:9640: After Get ASIC NUM CRC error counter=0
main.c:9663: set_baud=0
main.c:10588: The min freq=700
main.c:10590: set real timeout 52, need sleep=379392
main.c:12720: After TEST CRC error counter=0
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:14167: search freq for 1 times, completed chain = 2, total chain num = 2 
board_frq_tuning.c:549: single_board_frq_tuning enter
board_frq_tuning.c:550: min_rate, des_rate, fix_volt:13800, 14000, 880
board_frq_tuning.c:132: force_freq not set, don't need tuning
driver-bitmain.c:1840: set_reset_allhashboard = 0x0000ffff
driver-bitmain.c:1840: set_reset_allhashboard = 0x00000000
main.c:14559: restart Miner chance num=2
main.c:14599: waiting for receive_func to exit!
main.c:14613: waiting for pic heart to exit!
main.c:13809: bmminer not found= 1374 root       0:00 grep bmminer

main.c:14657: bmminer not found, restart bmminer ...
This is the first time running after searching freq!
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Tue Jul 17 18:03:36 CST 2018 type: Antminer S9i
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 80242d292f90481c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=30600
get fan[2] speed=30600
get fan[2] speed=30600
get fan[5] speed=4560
get fan[2] speed=30600
get fan[5] speed=4560
get fan[2] speed=30600
get fan[5] speed=4560
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:14951:bitmain_c5_init: last_freq: 0x00 0x7d 0x0f 0x4c 0x0c 0x4c 0x04 0x4c 0x0c 0x4c 0x00 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x03 0x4c 0x01 0x4c 0x01 0x4c 0x0f 0x4c 0x0f 0x4c 0x0f 0x4c 0x0f 0x4c 0x05 0x4c 0x07 0x4c 0x23 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 0x00 0x4c 
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
driver-btm-c5.c:14951:bitmain_c5_init: last_freq: 0x00 0x7d 0x0f 0x47 0x0c 0x47 0x04 0x47 0x07 0x47 0x00 0x47 0x03 0x47 0x03 0x47 0x03 0x47 0x03 0x47 0x03 0x47 0x03 0x47 0x01 0x47 0x01 0x47 0x0f 0x47 0x0f 0x47 0x0f 0x47 0x0f 0x47 0x05 0x47 0x09 0x47 0x23 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 0x00 0x47 
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=1 : 1
Chain[J8] has backup chain_voltage=890
Check chain[7] PIC fw version=0x03
driver-btm-c5.c:14014:init_exist_chain_table: total_exist_chain_num = 2
Chain[J7] orignal chain_voltage_pic=6 value=940
Chain[J7] will use backup chain_voltage_pic=870 [125]
Chain[J7] get working chain_voltage_pic=125
Chain[J8] orignal chain_voltage_pic=6 value=940
Chain[J8] will use backup chain_voltage_pic=890 [91]
Chain[J8] get working chain_voltage_pic=91
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 29 asic
Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 27 asic
driver-btm-c5.c:6334:set_frequency: Chain[J7] has core num in PIC
driver-btm-c5.c:6344:set_frequency: Chain[J7] ASIC[25] has core num=1
driver-btm-c5.c:6344:set_frequency: Chain[J7] ASIC[42] has core num=15
driver-btm-c5.c:6334:set_frequency: Chain[J8] has core num in PIC
driver-btm-c5.c:6374:set_frequency: miner total rate=9210GH/s ideal_total_hash_rate = 9000GH/s
driver-btm-c5.c:6399:set_frequency: read PIC voltage=940 on chain[6]
driver-btm-c5.c:6401:set_frequency: Chain:6 chipnum=29
driver-btm-c5.c:6418:set_frequency: Chain[J7] voltage added=0.0V
driver-btm-c5.c:6530:set_frequency: Chain:6 temp offset=-4
driver-btm-c5.c:6535:set_frequency: Chain:6 base freq=662
Asic[ 0]:662 Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:662 Asic[ 6]:662 Asic[ 7]:662 
Asic[ 8]:662 Asic[ 9]:662 Asic[10]:662 Asic[11]:662 Asic[12]:662 Asic[13]:662 Asic[14]:662 Asic[15]:662 
Asic[16]:662 Asic[17]:662 Asic[18]:662 Asic[19]:662 Asic[20]:662 Asic[21]:662 Asic[22]:662 Asic[23]:662 
Asic[24]:662 Asic[25]:662 Asic[26]:662 Asic[27]:662 Asic[28]:662 
driver-btm-c5.c:6571:set_frequency: Chain:6 max freq=662
driver-btm-c5.c:6572:set_frequency: Chain:6 min freq=662

driver-btm-c5.c:6399:set_frequency: read PIC voltage=940 on chain[7]
driver-btm-c5.c:6401:set_frequency: Chain:7 chipnum=27
driver-btm-c5.c:6418:set_frequency: Chain[J8] voltage added=0.0V
driver-btm-c5.c:6530:set_frequency: Chain:7 temp offset=-4
driver-btm-c5.c:6535:set_frequency: Chain:7 base freq=631
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 
Asic[16]:631 Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 
Asic[24]:631 Asic[25]:631 Asic[26]:631 
driver-btm-c5.c:6571:set_frequency: Chain:7 max freq=631
driver-btm-c5.c:6572:set_frequency: Chain:7 min freq=631


driver-btm-c5.c:6581:set_frequency: Miner fix freq ...
driver-btm-c5.c:6616:set_frequency: read PIC voltage=940 on chain[6]
driver-btm-c5.c:6617:set_frequency: Chain:6 chipnum=29
driver-btm-c5.c:6636:set_frequency: Chain[J7] voltage added=0.0V
driver-btm-c5.c:6778:set_frequency: Chain:6 temp offset=-4
driver-btm-c5.c:6783:set_frequency: Chain:6 base freq=662
Asic[ 0]:662 Asic[ 1]:662 Asic[ 2]:662 Asic[ 3]:662 Asic[ 4]:662 Asic[ 5]:662 Asic[ 6]:662 Asic[ 7]:662 
Asic[ 8]:662 Asic[ 9]:662 Asic[10]:662 Asic[11]:662 Asic[12]:662 Asic[13]:662 Asic[14]:662 Asic[15]:662 
Asic[16]:662 Asic[17]:662 Asic[18]:662 Asic[19]:662 Asic[20]:662 Asic[21]:662 Asic[22]:662 Asic[23]:662 
Asic[24]:662 Asic[25]:662 Asic[26]:662 Asic[27]:662 Asic[28]:662 
driver-btm-c5.c:6830:set_frequency: Chain:6 max freq=662
driver-btm-c5.c:6831:set_frequency: Chain:6 min freq=662

driver-btm-c5.c:6616:set_frequency: read PIC voltage=940 on chain[7]
driver-btm-c5.c:6617:set_frequency: Chain:7 chipnum=27
driver-btm-c5.c:6636:set_frequency: Chain[J8] voltage added=0.0V
driver-btm-c5.c:6778:set_frequency: Chain:7 temp offset=-4
driver-btm-c5.c:6783:set_frequency: Chain:7 base freq=631
Asic[ 0]:631 Asic[ 1]:631 Asic[ 2]:631 Asic[ 3]:631 Asic[ 4]:631 Asic[ 5]:631 Asic[ 6]:631 Asic[ 7]:631 
Asic[ 8]:631 Asic[ 9]:631 Asic[10]:631 Asic[11]:631 Asic[12]:631 Asic[13]:631 Asic[14]:631 Asic[15]:631 
Asic[16]:631 Asic[17]:631 Asic[18]:631 Asic[19]:631 Asic[20]:631 Asic[21]:631 Asic[22]:631 Asic[23]:631 
Asic[24]:631 Asic[25]:631 Asic[26]:631 
driver-btm-c5.c:6830:set_frequency: Chain:7 max freq=631
driver-btm-c5.c:6831:set_frequency: Chain:7 min freq=631

driver-btm-c5.c:6839:set_frequency: max freq = 662
driver-btm-c5.c:5954:ProcessFixFreq: totalRate = 9210, fixed_totalRate = 9000
set baud=1
driver-btm-c5.c:13950:set_working_voltage: chain[6] last_testpatten_highest_pcb_temp = 0
driver-btm-c5.c:13907:slowly_downgrade_voltage: chain[6] current_voltage_value = 940
driver-btm-c5.c:13908:slowly_downgrade_voltage: chain[6] target_voltage_value = 870
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 930
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 920
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 910
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 900
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 890
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 880
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[6] set voltage to 870
driver-btm-c5.c:13935:slowly_downgrade_voltage: chain[6] set working voltage to 870
driver-btm-c5.c:13950:set_working_voltage: chain[7] last_testpatten_highest_pcb_temp = 0
driver-btm-c5.c:13907:slowly_downgrade_voltage: chain[7] current_voltage_value = 940
driver-btm-c5.c:13908:slowly_downgrade_voltage: chain[7] target_voltage_value = 890
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 930
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 920
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 910
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 900
driver-btm-c5.c:13925:slowly_downgrade_voltage: chain[7] set voltage to 890
driver-btm-c5.c:13935:slowly_downgrade_voltage: chain[7] set working voltage to 890
driver-btm-c5.c:15764:bitmain_c5_init: start thread for read temp
setStartTimePoint total_tv_start_sys=197 total_tv_end_sys=198
restartNum = 2 , auto-reinit enabled...
driver-btm-c5.c:10467:read_temp_func: last_testpatten_highest_pcb_temp = -100
do read_temp_func once...

get RT hashrate from Chain[6]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=0.00000 Asic[08]=0.00000 
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000 
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000 
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Asic[28]=0.00000 
get RT hashrate from Chain[7]: (asic index start from 1-63)
Asic[01]=0.00000 Asic[02]=0.00000 Asic[03]=0.00000 Asic[04]=0.00000 Asic[05]=0.00000 Asic[06]=0.00000 Asic[07]=805.306 Asic[08]=0.00000 
Asic[09]=0.00000 Asic[10]=0.00000 Asic[11]=0.00000 Asic[12]=0.00000 Asic[13]=0.00000 Asic[14]=0.00000 Asic[15]=0.00000 Asic[16]=0.00000 
Asic[17]=0.00000 Asic[18]=0.00000 Asic[19]=0.00000 Asic[20]=0.00000 Asic[21]=0.00000 Asic[22]=0.00000 Asic[23]=0.00000 Asic[24]=0.00000 
Asic[25]=0.00000 Asic[26]=0.00000 Asic[27]=0.00000 Check Chain[J7] ASIC RT error: (asic index start from 1-63)
Asic[29]=4503599.627000
Check Chain[J8] ASIC RT error: (asic index start from 1-63)
Asic[07]=805.306000
Done check_asic_reg
Done read temp on Chain[6]
Done read temp on Chain[7]
Max pcb temp : -100
set FAN speed according to: temp_highest=-100 temp_top1[PWM_T]=-100 temp_top1[TEMP_POS_LOCAL]=-100 temp_change=0 fix_fan_steps=0
FAN PWM: 0
read_temp_func Done!
CRC error counter=1290

Then, after ~3 min the antminer restarts.

Thanks for reading and thanks in advance for any help i can get from here. Have a nice day.

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

There are some possible reasons why the hashrate drop or one of the hashboard is zero. Check this problem and solution

Or post your kernel logs here I will try to analyze the problem and give you some solution.

You can find the kernel logs under system>kernel logs then paste it here as a code.

scoxdo

newbie

Activity: 4

Merit: 0

Hi Guys! Long time lurker here and ive just created an account to seek some help about an issue on my antminer. In the inserted image you can see in the ASIC section how the 0's are incomplete and, in the the hashes section, how they are soooo low. Have anyone had got this issue? If so, how can it be fixed? I dont want to give up on it yet until im sure that this problem is unfixable. Thanks for reading and have a nice day.

https://imgur.com/YEjzYg4

Topic: ASIC codes on blades are not Ok. (Read 168 times)