Attic Exhausting | Bitcointalksearch.org

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Quote from: ?? on ??

I know this is old as hell but i pulled the trigger on this today: https://quietcoolsystems.com/garage-fan/. Specifically the GA ES-1500 model.

I know the fan is spendy but again this will keep the integrity of garage for home resale if/when that occurs.

Pulled the trigger since summer is here, price is pumping, and I don't want to turn units off mid day and should able add a couple more units with out worry.

Hopefully some pics when unit arrives and installed.

Fan is in and will need to install the other garage door vent as the house and yard door want to draw closed. Currently the door is lifted less than an inch to allow more air but temps from UI don't show over 85C mid day at 80F outside. Not sure what ambient in the garage is but will have sensor in a couple weeks. Hoping this will hold three more units if I'm lucky and will look to vent through the side of the house by fall/winter if I still don't want to touch the roof.

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

I'll have them come out again to check. All soffits have been opened and 1300 CFM in the gable.

mgoz

full member

Activity: 265

Merit: 232

Key components are ventilation and sealing warm air leaks. The temperature of your attic should be the same as outside temperature, but there are a lot of factors that will affect that. One thing that was not mentioned in that video is to not block soffits. In the video it looks like they may have blocked the soffits spraying foam directly into them which pretty much destroys ventilation. You need to have open soffits to let the air in. If using standard roll insulation, there are baffles you can install to allow the air in while still insulating around. I had to install vents all along one side of the roof on a house I purchased about a year ago because they not only blocked with insulation, but also blocked off entirely with a fascia board. Don't know how some people even call themselves roofers or contractors.

wtfonly16

full member

Activity: 285

Merit: 105

Quote from: Megaquake on September 10, 2018, 08:18:06 AM

I use 8 12v 6000rpm 120MM fans in 2 windows on each end of the room can be done in the attic mounted to ducting and plywood ~2000cfm for 8 and less than 600 watts for all 16

The air they create moves the shrubbery allot 10ft away outside lol

thats pretty bad considering you can get 3300+cfm for 180 watts using a 20inch blower on a single window. 1600rpm low pitch rumble vs screaming server fans...

Quote from: minefarmbuy on September 10, 2018, 09:48:24 AM

I live in the NW of the states so I actually have mold issues due to moisture. My inspector said more heat and ventilation will reduce it. In a sense dry it out and air flow. The ice damming maybe an issue. Once winter is here it will be more about retaining heat, as well at night I'll just be letting the heat move into the house or look to figure a way to let it circulate through the HVAC.

https://www.youtube.com/watch?v=VcRPGQoeO9Q this video describes the winter snow on the roof problem with a hot attic.

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Quote from: Megaquake on September 10, 2018, 08:18:06 AM

I use 8 12v 6000rpm 120MM fans in 2 windows on each end of the room can be done in the attic mounted to ducting and plywood ~2000cfm for 8 and less than 600 watts for all 16

The air they create moves the shrubbery allot 10ft away outside lol

Sounds effective but reducing noise is the reason I'm looking to vent to the attic. Wink

Quote from: mgoz on September 10, 2018, 08:41:37 AM

If you live where it snows, I'd be concerned with ice damming, mold, and shortening the life of your roof. It's generally a bad idea to exhaust air directly into an attic, especially warm air in the winter. If the plan is to run it all through ducting to an exhaust fan, then you should be OK.

I live in the NW of the states so I actually have mold issues due to moisture. My inspector said more heat and ventilation will reduce it. In a sense dry it out and air flow. The ice damming maybe an issue. Once winter is here it will be more about retaining heat, as well at night I'll just be letting the heat move into the house or look to figure a way to let it circulate through the HVAC.

mgoz

full member

Activity: 265

Merit: 232

If you live where it snows, I'd be concerned with ice damming, mold, and shortening the life of your roof. It's generally a bad idea to exhaust air directly into an attic, especially warm air in the winter. If the plan is to run it all through ducting to an exhaust fan, then you should be OK.

Megaquake

hero member

Activity: 630

Merit: 506

I use 8 12v 6000rpm 120MM fans in 2 windows on each end of the room can be done in the attic mounted to ducting and plywood ~2000cfm for 8 and less than 600 watts for all 16

The air they create moves the shrubbery allot 10ft away outside lol

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

So I ordered the door louvers since it's cooling down here this seemed like the best place to start. Would hate to go through another season of the door lifted even just a couple inches.

Still trying to talk to manufacturers about demo'ing or wholesale but no one likes to send us stuff lol . . not that I blame them. I'd just talk about it all day ffs. Only update for now. I'll hope to have pics of the door up in the next couple weeks.

bitcoinguy123

jr. member

Activity: 36

Merit: 1

It’s easy to adjust the temps using the controller that comes with it but it’s mostly made for only higher temperatures since these fans are meant for attic exhaust where it would only cut on when it gets to a set high point...in my case I wanted to constantly pull out the heat and not let it build up so I bypassed it.

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Sorry, thought he picture would be bigger.

The fan and duct are 16 in.
The reducer is a 16 to 12in.
The register is 14in x 14in to 12in
yes on the 2.8k CFM

Would like to keep the green model for less draw. but the red model like mentioned is just over 3k CFM

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: minefarmbuy on July 23, 2018, 01:41:46 PM

Is the 2350 cfm a calculation factoring the length of the ducting? The one on the quick price out is 2.8k cfm. So I should move to 3k+ for sure from you recommendation?

Reason for one hole is this is our garage, need to keep it aesthetically in tack more so than what I would once I get to the point of moving to find cheaper power.

the image was not very clear I thought it read 2350cfm.

but as to hole size and length of tubing.

the longer the tube = more friction
the smaller the diameter = more friction

so a 1600cfm fan with 1 foot tube length to move the air

and at the same 1 foot diameter moves air a lot better then

a 2800 cfm fan with a 10 inch tube and a six foot length .

when I read your chart I saw a reducer in it 12 to 10 inches
I saw a tube six feet long
I read a 2350 cfm fan

and I thought it may not work

if the tubing is 1 foot with no reducer
the fan is 2800cfm
and the tube length is six feet I think you will be close to okay

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Thanks Raymond. I just wanted to understand phma's thoughts more. The link is helpful.

Btcguy, Nice, come winter I won't need as much exhaust. Is it too much stress you think to set a temp? Starting and stopping more frequently? Garage will get pretty cold, will be interesting to see what these auto fans will drop to.

bitcoinguy123

jr. member

Activity: 36

Merit: 1

Take a look at my post of my setup. I'm using similar fan and it works great. I got the red fan with higher cfm and bypassed the thermostat switch and its running 24/7 non stop for months now.

Here a link to my posts.

https://bitcointalksearch.org/topic/m.29355077

Raymond_B

member

Activity: 504

Merit: 71

Just Getting Started...

I think Philip is simply illustrating the effect of both ductwork diameter and length.

This is a pretty good site that might help with your calculations. https://apps.engineeringtoolbox.com/air-ducts-velocity-a_27.html

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Is the 2350 cfm a calculation factoring the length of the ducting? The one on the quick price out is 2.8k cfm. So I should move to 3k+ for sure from you recommendation?

Reason for one hole is this is our garage, need to keep it aesthetically in tack more so than what I would once I get to the point of moving to find cheaper power.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: minefarmbuy on July 22, 2018, 11:05:39 PM

What I have on that HD screenshot is a 12in register with 16in duct to fit over the gable fan. I would maybe want 6ft of ducting at most. just enough to reach the fan suspended from the rafters. Thoughts on those diameters?

maybe.

I can do 12 x 1350 = 16200 watts with 2 gable fans and no space

so 3200 cfm is moving enough air to cool 1350 watts

but the fans are both 12 inches the cable vents are both 16 inches

I have two not one and the spacing from the gear is under 1 foot.

if you have 8 x 1350 = 10800 watts

your one fan is 2350 cfm

you have one 12 inch hole not 2
and you move the air 6 to 7 feet.

I think it could work but you may be short.

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Quote from: philipma1957 on July 22, 2018, 10:43:42 PM

I see you want a single hole. A ten inch hole is too small. You will restrict airflow.

And you are looking to move the air more then six feet. That restricts air flow

What I have on that HD screenshot is a 12in register with 16in duct to fit over the gable fan. I would maybe want 6ft of ducting at most. just enough to reach the fan suspended from the rafters. Thoughts on those diameters?

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

I see you want a single hole. A ten inch hole is too small. You will restrict airflow.

And you are looking to move the air more then six feet. That restricts air flow

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Ok great so my assumption or feeling that 3k was bout ball park for the hot weather in removal. Not everything is an antminer half of my four units are currently. Since I probably won't max more than 8 i'll look to move forward in the next few weeks with the project.

I know gable fans come with humidifiers and thermostats, but since I'll want the fan on always but not just at max I'll look and see if there are or is a way to wire the fan to reduce/gain speed at certain temps and not just shut off entirely. So far I see only dual speed models.

banman24

member

Activity: 103

Merit: 10

Quote from: minefarmbuy on July 18, 2018, 10:33:02 PM

I wouldn't be able to run more than the eight with my power as is. Plus this is at home and I'll hope to venture out to cheaper power and bigger space if/as needed. So 3k would be plenty and the 1.6k cfm would be about the minimum then?

are they all s9's? I wouldn't want my farm to have "The minimum amount of cfm exhaust" I would rather have more than enough to accommodate for the few days of the year where it might get extremely hot outside. Calculating the CFM on these really isn't like hard numbers, by that I mean the fans on the machines are variable speeds. At full speed the s9's move almost 300cfm, If you take that into consideration 8*300=2400CFM. Thats worst case scenario (I would build it to those numbers), the colder the intake temp on the miners the slower the fans spin meaning the less cfm they actually move.

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

I wouldn't be able to run more than the eight with my power as is. Plus this is at home and I'll hope to venture out to cheaper power and bigger space if/as needed. So 3k would be plenty and the 1.6k cfm would be about the minimum then?

banman24

member

Activity: 103

Merit: 10

Quote from: minefarmbuy on July 17, 2018, 11:51:31 AM

Priced out the build, can defiantly save on the fan and hopefully other items. Thoughts? Only concern was ensuring intake, any others? or other suggestions? I just want to do one duct register in the ceiling, so would 3k CFM removal be overkill for a small farm of 8 asics on a 100F day? Bout as hot as it would typically get through a few summer days here.

[...]

Yes 3000CFM will be fine for 8 units, it allows you to have some wiggle room and if you wanted to throw in one or 2 more machines you could if you wanted.

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Priced out the build, can defiantly save on the fan and hopefully other items. Thoughts? Only concern was ensuring intake, any others? or other suggestions? I just want to do one duct register in the ceiling, so would 3k CFM removal be overkill for a small farm of 8 asics on a 100F day? Bout as hot as it would typically get through a few summer days here.

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Quote from: lightfoot on July 16, 2018, 09:21:29 PM

Just stick them in a window, exhaust pointing out. 100% dump heat outside and if you run AC inside you should be good.

I do this with 6 old Titans, works fine.

I would if my neighbors house wasn't so close to the garage and all their window seem to be on the that same side. So the venting into attic is best alternative. I would vent straight out the through the roof but it's new and don't want to fuck with it since it rains most the year here. I don't want four units running in the house either.

To recap: build will work, not much difference from DYI from the premade unit. Ensure air flow and we're golden?

lightfoot

legendary

Activity: 3164

Merit: 2258

I fix broken miners. And make holes in teeth :-)

Just stick them in a window, exhaust pointing out. 100% dump heat outside and if you run AC inside you should be good.

I do this with 6 old Titans, works fine.

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Nice, I have that one in the house gable already and their 1300 above the garage where the current farm exhaust exits. I can really only support four more units, so eight total till i'm out grown. 3k CFM removal should be plenty with in door vents and/or garage door up some correct? Might as well fit for max capacity since I need to upgrade it anyway. What CFM should I hit with 8 asics? min would be around 1600 I assume? So 3k if able to adjust would be great in the summer?

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Listen to Nasty

you will need to feed air in.

Here are good gable fans to pull air out.

https://www.homedepot.com/p/Master-Flow-1600-CFM-Power-Gable-Mount-Attic-Fan-EGV6/205924917

I use 2 of them in the solar array

see photo

https://i.imgur.com/5em72rF.jpg

youtube show heat and noise shield

https://www.youtube.com/watch?v=HKlXarvBv5M&t=1s

OgNasty

donator

Activity: 4760

Merit: 4323

Leading Crypto Sports Betting & Casino Platform

Quote from: minefarmbuy on July 15, 2018, 11:10:21 AM

Hi personal post here.

I'm a small home miner and wanted to increase capacity and not have neighbors kill me. So exhausting through garage wall directly isn't an option. I have decent removal but want add more units and will need to increase exhausting. Been looking at whole house fans to install above miners but the cost is pretty high. These look simple to construct from high CFM gable fan, ceiling register with flex duct, and of course mounting braces from rafters. Should be able to save quite a bit with DYI, just want to make sure I'm not missing any critical differences from a pre-constructed whole house fan to building one as described. Thanks.

The main piece of advice I can give is to be aware of where you'll be taking air in. For all the air you exhaust, you will intake the same amount somewhere.

minefarmbuy

full member

Activity: 1022

Merit: 221

We are not retail.

Hi personal post here.

I'm a small home miner and wanted to increase capacity and not have neighbors kill me. So exhausting through garage wall directly isn't an option. I have decent removal but want add more units and will need to increase exhausting. Been looking at whole house fans to install above miners but the cost is pretty high. These look simple to construct from high CFM gable fan, ceiling register with flex duct, and of course mounting braces from rafters. Should be able to save quite a bit with DYI, just want to make sure I'm not missing any critical differences from a pre-constructed whole house fan to building one as described. Thanks.

Topic: Attic Exhausting (Read 657 times)