AvalonMiner 1246 | Bitcointalksearch.org

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

Based in your logs what I see is that the two hashboards are overheating and your tmax is reach more than 85c this can cause miner to stop hashing.

What I would like you to try is to cool down your miner try to put extra fan and make sure to exhaust hotair/heat from the room.
You can also run the fan at 90% or full speed to help hashboard to cool down.

You can use this command below to increase the fan speed.

Code:

[{"command":"ascset","parameter":"0,fan-spd,90"}]

You can submit this command using FMS under diagnose.

MinerMetrix

newbie

Activity: 6

Merit: 0

On your backstage log it indicates "WORKMODE[0]". Which means your unit is in normal operation mode, so I will never reach within 6% of designated hash rate. Click on the ">Configuration" link on the backstage, then at the very bottom change the "Mode:" dropdown to "High Performance". Click 'Reboot' and it should fully hash.

MinerMetrix

newbie

Activity: 6

Merit: 0

Quote from: SunGlassesRon on December 07, 2022, 03:32:33 PM

Hello All
I bought 2 of these miners from Aliexpress AvalonMiner 1246 they both where mining fine till one packed up after a week and a half. They did not overheat as I live in UK and it is cold in my garage the hottest board was around 70 to 72 I have been back and forth with seller but they either are useless or know what problem is and don't care I am no expert but I thought since I had two the first thing I swapped was the PSU with no success so today I swapped the control board still no good. My problem is I cant understand how all 3 boards could go down I am contemplating swapping a board but I know there are experts here so I thought I could show log and someone could point me in right direction.
Many thanks for any advice

https://www.dropbox.com/s/a3qx9wkj45k9yyw/Screenshot%202022-12-07%2013.05.20.png?dl=0

https://www.dropbox.com/s/66kirln63bdke18/Screenshot%202022-12-07%2013.05.12.png?dl=0

The unit is in normal mode, it needs to be in High Performance mode (Configuration tab on the backstage, after changing click Reboot). None of your fans are connect/working. Only found 1 hash board with 120 total ASICS, indicating possible hash board problems. Your SF is not the same as your ATABD's, either the frequency command was entered or it is auto-tuning to shut down due to no hash rate in 5 minutes.

MinerMetrix

newbie

Activity: 6

Merit: 0

Quote from: BitMaxz on December 12, 2022, 05:50:58 PM

It seems that the fan is not automatically running at high speed after the hash board reaches its temp limit.

Would you mind to try aging to calibrate the miner?
Use the FMS tool to aging the miner you can download the tool here https://canaan.io/service/447

There is 3 FMS tool only one has an aging button so download the 2nd or I think the 3rd one from that link.

If you start the aging process without 3 good hash boards then it will be stuck in aging-mode until you fix the hash boards. All versions of FMS have the command line tool: click the diagnose button.

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

Quote from: ?? on ??

Did you say before about aging miner it was mentioned by avalon support but I am not sure how to do that.

Many Thanks for any advice

I already post it before from my previous post that you can try aging just download the tool from Canaan the link is already my post above.

Make sure to download version 2.3.3 because the other FMS tool doesn't have the aging button that's the easier one.
However, you can download other FMS tools and use commands to aging the miner. You can find commands on my old post below including the Aging command.

- https://bitcointalksearch.org/topic/m.59012568

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

Is it stuck on scanning? Would you mind to try to hold the func button for 15sec from your miner while the FMS tool is scanning if didn't work try the rst button?

If still stuck on scanning it might be your PC firewall blocking it from scanning. Try to disable the firewall first and try again.

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

It seems that the fan is not automatically running at high speed after the hash board reaches its temp limit.

Would you mind to try aging to calibrate the miner?
Use the FMS tool to aging the miner you can download the tool here https://canaan.io/service/447

There is 3 FMS tool only one has an aging button so download the 2nd or I think the 3rd one from that link.

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

Bootby said it has no hashrate and the systemstatus says you only have one hashboard detected.

Maybe the PSU you replaced is defective or incompatible with your unit.
However, the logs say a few hashboard have lost contact try the cable if they do have a connection if it doesn't have any connection replace them or if it still doesn't work the two hashboard might be already broken. Try to run them one by one to check which detected normally and then swap PSU wires and cables to other hashboard that are not detected to the detected one to test.

ben120

newbie

Activity: 5

Merit: 0

Hello! I'm not sure I understand everything, but your miner seems to work, it looks like a configuration problem, I'll leave you these few links, maybe they can help you, I had an avalon usb miner, but that's all what I can do

https://github.com/Canaan-Creative

https://download.canaan-creative.com/

https://holybitcoin.com/avalon-nano-setup-guide/

on github or on the "holy bitcoin store" you could be informed

SunGlassesRon

newbie

Activity: 20

Merit: 1

Hello All
I bought 2 of these miners from Aliexpress AvalonMiner 1246 they both where mining fine till one packed up after a week and a half. They did not overheat as I live in UK and it is cold in my garage the hottest board was around 70 to 72 I have been back and forth with seller but they either are useless or know what problem is and don't care I am no expert but I thought since I had two the first thing I swapped was the PSU with no success so today I swapped the control board still no good. My problem is I cant understand how all 3 boards could go down I am contemplating swapping a board but I know there are experts here so I thought I could show log and someone could point me in right direction.
Many thanks for any advice

https://www.dropbox.com/s/a3qx9wkj45k9yyw/Screenshot%202022-12-07%2013.05.20.png?dl=0

https://www.dropbox.com/s/66kirln63bdke18/Screenshot%202022-12-07%2013.05.12.png?dl=0

Topic: AvalonMiner 1246 (Read 254 times)