Can you please advise which type of cable should I use in place of cable #3?[/b][/color]
#3 is just a molex=>sata adapter (it's obviously detachable). Your riser needs a molex (4-pin) connector, so just use one of the molex cables straight from your PSU. 
Topic: Can you please help me in correcting my understanding (Read 268 times)
Hi,
Can you please help me in correcting my understanding on how riser will be connected on rig.
Please refer the following image:
Thanking you in anticipation.
Regards,
Riz
Can you please help me in correcting my understanding on how riser will be connected on rig.
Please refer the following image:
Thanking you in anticipation.
Regards,
Riz
Riz, i'll save you a world of pain.
Do yourself a favor and throw that #3 SATA cable in the bin.
Then read this link: https://www.reddit.com/r/EtherMining/wiki/hardware/risers
Now repeat after me "Do not use any included harnesses that converts to SATA"
Your local fire department thanks you
Hi bigjee,
Thanks. Great help indeed
Understood that ver007 mustn't be used.
Can you please advise which type of cable should I use in place of cable #3?
Nr 3 connects to the same PSU with the SATA connector.
I recommend not to use this wire that came with the riser but connect directly from your PSU.
Could you write down your model of your PSU?
Then I could make a schematic how to connect all the wires.
I recommend not to use this wire that came with the riser but connect directly from your PSU.
Could you write down your model of your PSU?
Then I could make a schematic how to connect all the wires.
I have Corsair HX1200i. Would really appreciate if you could make a schematic diagram. Risers/GPUs is a big grey area for me and I am full of doubts, fear about that.
Hi,
Can you please help me in correcting my understanding on how riser will be connected on rig.
Please refer the following image:
Thanking you in anticipation.
Regards,
Riz
Can you please help me in correcting my understanding on how riser will be connected on rig.
Please refer the following image:
Thanking you in anticipation.
Regards,
Riz
Riz, i'll save you a world of pain.
Do yourself a favor and throw that #3 SATA cable in the bin.
Then read this link: https://www.reddit.com/r/EtherMining/wiki/hardware/risers
Now repeat after me "Do not use any included harnesses that converts to SATA"
Your local fire department thanks you
The riser pictured is supposed to be powered with a 4-pin molex connector. It's just they already included a molex=>sata adapter as well. Which is not recommended to use unless you 100% sure that your particular card draws very little power via the pci-e slot. Otherwise just disconnect that adapter from the riser and connect the riser to the PSU directly with a molex cable.
Nr 3 connects to the same PSU with the SATA connector.
I recommend not to use this wire that came with the riser but connect directly from your PSU.
Could you write down your model of your PSU?
Then I could make a schematic how to connect all the wires.
I recommend not to use this wire that came with the riser but connect directly from your PSU.
Could you write down your model of your PSU?
Then I could make a schematic how to connect all the wires.
3 is connected to you Power Supply Unit, for sata power, like hdd, ssd
you will see them on your PSU, usually there are a buch of them, like 4-6 pcs and it connects one way only
you will see them on your PSU, usually there are a buch of them, like 4-6 pcs and it connects one way only
Hi,
Can you please help me in correcting my understanding on how riser will be connected on rig.
Please refer the following image:
Thanking you in anticipation.
Regards,
Riz
Can you please help me in correcting my understanding on how riser will be connected on rig.
Please refer the following image:
Thanking you in anticipation.
Regards,
Riz
Jump to: