Finally figured it out !!!
On some miners you need to plug in a dummy DVI plug or a monitor cable to one of the video cards. Dont ask me why because i have a ton of miners that do need this. Once i did this and disabled the onboard video card the miner started working.
Topic: Claymore 11.7 miner starts then PAUSES...does not close ! (Read 187 times)
Guys,
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
have you tried running 1 GPU on PCIex16 slot? dont use riser
I have a feeling that one of your hardware might caused your issue
i havent but i will give it a try..whats strange is that they were all working before the windows update....thanks
Let me know if you figure it out. Im having the same issue and im ready to thrown my rig out of the window.
Guys,
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
have you tried running 1 GPU on PCIex16 slot? dont use riser
I have a feeling that one of your hardware might caused your issue
i havent but i will give it a try..whats strange is that they were all working before the windows update....thanks
I'm glad someone else brought this up. I have the EXACT same issue. It runs and runs, than pauses.
Guys,
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
have you tried running 1 GPU on PCIex16 slot? dont use riser
I have a feeling that one of your hardware might caused your issue
Guys,
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
I have one miner that i cannot figure out. Mind you i have 30+ but yes i cannot figure this one out, and its driving me nuts.
The issue is that after the Windows 10 April update the miner will start but pauses....it does not close. I have tried everything i know and nothing. So i went ahead and installed a clean version of 1709 build with all of its updates.
I have reinstalled 11.7(which was working with no issues prior) and still nothing. I have tried adrenaline 18.2 and even downgraded to the blockchain drivers and still nothing. The motherboard is up to date, windows sees all the cards...no issues there. I have patched the drivers...etc...etc...
These are AMD RX560's that have been modded...and again these were working fine before the darn update got me.....I have also excluded the claymore folder in defender, set a pause for 30 seconds etc...
Im hoping someone out there has run into this prior....
Any help would be appreciated
Thanks
Jump to: