Topic: Claymores freezes. Help! (Read 509 times)

I'd recommend switching to sgminer-gm.  No dev fee, and better stats for long-term average hashrate and HW errors.

Got it! Thank you. What does it do? Intensity do I loose hashing power?

you let the nvidia run at   91 c


okay  try -ehti 4      at  end of bat  and let me check on that.        typo  it is -ethi 4  look at bold line below


https://bitcointalksearch.org/topic/m.14501372
from link above

COMMAND LINE OPTIONS:

-epool    Ethereum pool address. Only Stratum protocol is supported for pools. Miner supports all pools that are compatible with Dwarfpool proxy and accept Ethereum wallet address directly.
   For solo mining, specify "http://" before address, note that this mode is not intended for proxy or HTTP pools, also "-allpools 1" will be set automatically in this mode.
   Note: The miner supports all Stratum versions for Ethereum, HTTP mode is necessary for solo mining only.
   Using any proxies will reduce effective hashrate by at least 1%, so connect miner to Stratum pools directly. Using HTTP pools will reduce effective hashrate by at least 5%.

-ewal    Your Ethereum wallet address. Also worker name and other options if pool supports it.
   Pools that require "Login.Worker" instead of wallet address are not supported directly currently, but you can use "-allpools 1" option to mine there.

-epsw    Password for Ethereum pool, use "x" as password.

-eworker Worker name, it is required for some pools.

-esm   Ethereum Stratum mode. 0 - eth-proxy mode (for example, dwarpool.com), 1 - qtminer mode (for example, ethpool.org),
   2 - miner-proxy mode (for example, coinotron.com), 3 - nicehash mode. 0 is default.

-etha   Ethereum algorithm mode for AMD cards. 0 - optimized for fast cards, 1 - optimized for slow cards, 2 - for gpu-pro Linux drivers. -1 - autodetect (default, automatically selects between 0 and 1).
   You can also set this option for every card individually, for example "-etha 0,1,0".

-asm   (AMD cards only) enables assembler GPU kernels. In this mode some tuning is required even in ETH-only mode, use "-dcri" option or or "+/-" keys in runtime to set best speed.
   Currently ETH-LBRY mode is not supported in assembler.
   Specify "-asm 0" to disable this option. You can also specify values for every card, for example "-asm 0,1,0". Default value is "1".
   If ASM mode is enabled, miner must show "GPU #x: algorithm ASM" at startup.
   Check "FINE-TUNING" section below for additional notes.
   NEW: added alternative assembler kernels for Tonga and Polaris cards for ETH-only mode. Use them if you get best speed at "-dcri 1" (i.e. you cannot find speed peak), use "-asm 2" option to enable this mode.

-ethi   Ethereum intensity. Default value is 8, you can decrease this value if you don't want Windows to freeze or if you have problems with stability. The most low GPU load is "-ethi 0".
   Also "-ethi" now can set intensity for every card individually, for example "-ethi 1,8,6".
   You can also specify negative values, for example, "-ethi -8192", it exactly means "global work size" parameter which is used in official miner.

-eres   this setting is related to Ethereum mining stability. Every next Ethereum epoch requires a bit more GPU memory, miner can crash during reallocating GPU buffer for new DAG.
   To avoid it, miner reserves a bit larger GPU buffer at startup, so it can process several epochs without buffer reallocation.
   This setting defines how many epochs miner must foresee when it reserves GPU buffer, i.e. how many epochs will be processed without buffer reallocation. Default value is 2.

-allpools Specify "-allpools 1" if miner does not want to mine on specified pool (because it cannot mine devfee on that pool), but you agree to use some default pools for devfee mining.
   Note that if devfee mining pools will stop, entire mining will be stopped too.

-allcoins Specify "-allcoins 1" to be able to mine Ethereum forks, in this mode miner will use some default pools for devfee Ethereum mining.
   Note that if devfee mining pools will stop, entire mining will be stopped too.
   Miner has to use two DAGs in this mode - one for Ethereum and one for Ethereum fork, it can cause crashes because DAGs have different sizes.
   Therefore for this mode it is recommended to specify current Ethereum epoch (or a bit larger value),
   for example, "-allcoins 47" means that miner will expect DAG size for epoch #47 and will allocate appropriate GPU buffer at starting, instead of reallocating bigger GPU buffer (may crash) when it starts devfee mining.
   Another option is to specify "-allcoins -1", in this mode miner will start devfee round immediately after start and therefore will get current epoch for Ethereum, after that it will be able to mine Ethereum fork.
   If you mine Expanse, the best way is to specify "-allcoins exp", in this mode devfee mining will be on Expanse too and DAG won't be recreated at all.

-etht   Time period between Ethereum HTTP requests for new job in solo mode, in milliseconds. Default value is 200ms.

-erate   send Ethereum hashrate to pool. Default value is "1", set "-erate 0" if you don't want to send hashrate.

-estale   send Ethereum stale shares to pool, it can increase effective hashrate a bit. Default value is "1", set "-estale 0" if you don't want to send stale shares.

-dpool    Decred/Siacoin/Lbry/Pascal pool address. Use "http://" prefix for HTTP pools, "stratum+tcp://" for Stratum pools. If prefix is missed, Stratum is assumed.
   Decred: both Stratum and HTTP are supported. Siacoin: both Stratum and HTTP are supported, though note that not all Stratum versions are supported currently. Lbry: only Stratum is supported.

-dwal   Your Decred/Siacoin/Lbry/Pascal wallet address or worker name, it depends on pool.

-dpsw    Password for Decred/Siacoin/Lbry/Pascal pool.

-di    GPU indexes, default is all available GPUs. For example, if you have four GPUs "-di 02" will enable only first and third GPUs (#0 and #2).
   Use "-di detect" value to detect correct GPU order for temperatures management (requires non-zero "-tt" option); note that it will not work properly if you do not want to assign all GPUs to miner (add "-gmap" option to fix it).
   You can also turn on/off cards in runtime with "0"..."9" keys and check current statistics with "s" key.

-gser   this setting can improve stability on multi-GPU systems if miner hangs during startup. It serializes GPUs initalization routines. Use "-gser 1" to serailize some of routines and "-gser 2" to serialize all routines.
   Default value is "0" (no serialization, fast initialization).

-mode   Select mining mode:
   "-mode 0" (default) means dual Ethereum + Decred/Siacoin/Lbry mining mode.
   "-mode 1" means Ethereum-only mining mode. You can set this mode for every card individually, for example, "-mode 1-02" will set mode "1" for first and third GPUs (#0 and #2).

-dcoin   select second coin to mine in dual mode. Possible options are "-dcoin dcr", "-dcoin sc", "-dcoin lbc", "-dcoin pasc". Default value is "dcr".

-dcri   Decred/Siacoin/Lbry/Pascal intensity, or Ethereum fine-tuning value in ETH-only ASM mode. Default value is 30, you can adjust this value to get the best Decred/Siacoin/Lbry mining speed without reducing Ethereum mining speed.
   You can also specify values for every card, for example "-dcri 30,100,50".
   You can change the intensity in runtime with "+" and "-" keys and check current statistics with "s" key.
   For example, by default (-dcri 30) 390 card shows 29MH/s for Ethereum and 440MH/s for Decred. Setting -dcri 70 causes 24MH/s for Ethereum and 850MH/s for Decred.

-dcrt   Time period between Decred/Siacoin HTTP requests for new job, in seconds. Default value is 5 seconds.

-ftime   failover main pool switch time, in minutes, see "Failover" section below. Default value is 30 minutes, set zero if there is no main pool.

-wd    watchdog option. Default value is "-wd 1", it enables watchdog, miner will be closed (or restarted, see "-r" option) if any thread is not responding for 1 minute or OpenCL call failed.
   Specify "-wd 0" to disable watchdog.

-r   Restart miner mode. "-r 0" (default) - restart miner if something wrong with GPU. "-r -1" - disable automatic restarting. -r >20 - restart miner if something
   wrong with GPU or by timer. For example, "-r 60" - restart miner every hour or when some GPU failed.
   "-r 1" closes miner and execute "reboot.bat" file ("reboot.bash" or "reboot.sh" for Linux version) in the miner directory (if exists) if some GPU failed.
   So you can create "reboot.bat" file and perform some actions, for example, reboot system if you put this line there: "shutdown /r /t 5 /f".

-retrydelay   delay, in seconds, between connection attempts. Default values is "20". Specify "-retrydelay -1" if you don't need reconnection, in this mode miner will exit if connection is lost.

-dbg   debug log and messages. "-dbg 0" - (default) create log file but don't show debug messages.
   "-dbg 1" - create log file and show debug messages. "-dbg -1" - no log file and no debug messages.

-logfile debug log file name. After restart, miner will append new log data to the same file. If you want to clear old log data, file name must contain "noappend" string.
   If missed, default file name will be used.

-nofee   set "1" to cancel my developer fee at all. In this mode some optimizations are disabled so mining speed will be slower by about 4%.
   By enabling this mode, I will lose 100% of my earnings, you will lose only 2-3% of your earnings.
   So you have a choice: "fastest miner" or "completely free miner but a bit slower".
   If you want both "fastest" and "completely free" you should find some other miner that meets your requirements, just don't use this miner instead of claiming that I need
   to cancel/reduce developer fee, saying that 1-2% developer fee is too much for this miner and so on.

-benchmark   benchmark mode, specify "-benchmark 1" to see hashrate for your hardware. You can also specify epoch number for benchmark, for example, "-benchmark 110".

-li   low intensity mode. Reduces mining intensity, useful if your cards are overheated. Note that mining speed is reduced too.
   More value means less heat and mining speed, for example, "-li 10" is less heat and mining speed than "-li 1". You can also specify values for every card, for example "-li 3,10,50".
   Default value is "0" - no low intensity mode.

-lidag   low intensity mode for DAG generation, it can help with OC or weak PSU. Supported values are 0, 1, 2, 3, more value means lower intensity. Example: "-lidag 1".
   You can also specify values for every card, for example "-lidag 1,0,3". Default value is "0" (no low intensity for DAG generation).

-tt   set target GPU temperature. For example, "-tt 80" means 80C temperature. You can also specify values for every card, for example "-tt 70,80,75".
   You can also set static fan speed if you specify negative values, for example "-tt -50" sets 50% fan speed. Specify zero to disable control and hide GPU statistics.
   "-tt 1" (default) does not manage fans but shows GPU temperature and fan status every 30 seconds. Specify values 2..5 if it is too often.
   Note: for NVIDIA cards only temperature monitoring is supported, temperature management is not supported.
   Note: for Linux gpu-pro drivers, miner must have root access to manage fans, otherwise only monitoring will be available.

-ttdcr   reduce Decred/Siacoin/Lbry/Pascal intensity automatically if GPU temperature is above specified value. For example, "-ttdcr 80" reduces Decred intensity if GPU temperature is above 80C.
   You can see current Decred intensity coefficients in detailed statistics ("s" key). So if you set "-dcri 50" but Decred/Siacoin intensity coefficient is 20% it means that GPU currently mines Decred/Siacoin at "-dcri 10".
   You can also specify values for every card, for example "-ttdcr 80,85,80". You also should specify non-zero value for "-tt" option to enable this option.
   It is a good idea to set "-ttdcr" value higher than "-tt" value by 3-5C.
   NOTE: Check "KNOWN ISSUES" section. GPU indexes in temperature control sometimes don't match GPU indexes in mining!

-ttli   reduce entire mining intensity (for all coins) automatically if GPU temperature is above specified value. For example, "-ttli 80" reduces mining intensity if GPU temperature is above 80C.
   You can see if intensity was reduced in detailed statistics ("s" key).
   You can also specify values for every card, for example "-ttli 80,85,80". You also should specify non-zero value for "-tt" option to enable this option.
   It is a good idea to set "-ttli" value higher than "-tt" value by 3-5C.
   NOTE: Check "KNOWN ISSUES" section. GPU indexes in temperature control sometimes don't match GPU indexes in mining!

-tstop   set stop GPU temperature, miner will stop mining if GPU reaches specified temperature. For example, "-tstop 95" means 95C temperature. You can also specify values for every card, for example "-tstop 95,85,90".
   This feature is disabled by default ("-tstop 0"). You also should specify non-zero value for "-tt" option to enable this option.
   NOTE: Check "KNOWN ISSUES" section. GPU indexes in temperature control sometimes don't match GPU indexes in mining!
   If it turned off wrong card, it will close miner in 30 seconds.
   You can also specify negative value to close miner immediately instead of stopping GPU, for example, "-tstop -95" will close miner as soon as any GPU reach 95C temperature.

-fanmax   set maximal fan speed, in percents, for example, "-fanmax 80" will set maximal fans speed to 80%. You can also specify values for every card, for example "-fanmax 50,60,70".
   This option works only if miner manages cooling, i.e. when "-tt" option is used to specify target temperature. Default value is "100".
   Note: for NVIDIA cards this option is not supported.

-fanmin   set minimal fan speed, in percents, for example, "-fanmin 50" will set minimal fans speed to 50%. You can also specify values for every card, for example "-fanmin 50,60,70".
   This option works only if miner manages cooling, i.e. when "-tt" option is used to specify target temperature. Default value is "0".
   Note: for NVIDIA cards this option is not supported.

-cclock   set target GPU core clock speed, in MHz. If not specified or zero, miner will not change current clock speed. You can also specify values for every card, for example "-cclock 1000,1050,1100,0".
   Unfortunately, AMD blocked underclocking for some reason, you can overclock only.
   Note: for NVIDIA cards this option is not supported.

-mclock   set target GPU memory clock speed, in MHz. If not specified or zero, miner will not change current clock speed. You can also specify values for every card, for example "-mclock 1200,1250,1200,0".
   Unfortunately, AMD blocked underclocking for some reason, you can overclock only.
   Note: for NVIDIA cards this option is not supported.

-powlim set power limit, from -50 to 50. If not specified, miner will not change power limit. You can also specify values for every card, for example "-powlim 20,-20,0,10".
   Note: for NVIDIA cards this option is not supported.

-cvddc   set target GPU core voltage, multiplied by 1000. For example, "-cvddc 1050" means 1.05V. You can also specify values for every card, for example "-cvddc 900,950,1000,970". Supports latest AMD 4xx cards only in Windows.
   Note: for NVIDIA cards this option is not supported.

-mvddc   set target GPU memory voltage, multiplied by 1000. For example, "-mvddc 1050" means 1.05V. You can also specify values for every card, for example "-mvddc 900,950,1000,970". Supports latest AMD 4xx cards only in Windows.
   Note: for NVIDIA cards this option is not supported.

-mport   remote monitoring/management port. Default value is -3333 (read-only mode), specify "-mport 0" to disable remote monitoring/management feature.
   Specify negative value to enable monitoring (get statistics) but disable management (restart, uploading files), for example, "-mport -3333" enables port 3333 for remote monitoring, but remote management will be blocked.
   You can also use your web browser to see current miner state, for example, type "localhost:3333" in web browser.
   Warning: use negative option value or disable remote management entirely if you think that you can be attacked via this port!
   By default, miner will accept connections on specified port on all network adapters, but you can select desired network interface directly, for example, "-mport 127.0.0.1:3333" opens port on localhost only.

-mpsw   remote monitoring/management password. By default it is empty, so everyone can ask statistics or manage miner remotely if "-mport" option is set. You can set password for remote access (at least EthMan v3.0 is required to support passwords).

-colors enables or disables colored text in console. Default value is "1", use "-colors 0" to disable coloring. Use 2...4 values to remove some of colors.

-v   displays miner version, sample usage: "-v 1".

-gmap   sets GPU order in fan/temperature list. This option is similar to "-di" option, but it manages fan/temperature list.
   For example, if you have two cards, you can change their order by adding "-gmap 10". Another example, reverse order for six cards: "-gmap 543210".
   This option is also useful if you want to exclude some GPUs from the list. For example, if you have four cards, you can exclude first GPU from fan/temperature list with "-gmap 123".

-altnum   alternative GPU indexing. This option does not change GPU order, but just changes GPU indexes that miner displays, it can be useful in some cases. Possible values are:
   0: default GPU indexing. For example, if you specify "-di 05" to select first and last GPUs of six GPUs installed, miner will display these two selected cards as "GPU0" and "GPU1".
   1: same as "0", but start indexes from one instead of zero. For example, if you specify "-di 05" to select first and last GPUs of six GPUs installed, miner will display these two selected cards as "GPU1" and "GPU2".
   2: alternative GPU indexing. For example, if you specify "-di 05" to select first and last GPUs of six GPUs installed, miner will display these two selected cards as "GPU0" and "GPU5".
   3: same as "2", but start indexes from one instead of zero. For example, if you specify "-di 05" to select first and last GPUs of six GPUs installed, miner will display these two selected cards as "GPU1" and "GPU6".
   Default value is "0".

I have 3x 480 and one gtx 1080, it was working fine but i needed to shut of the computer for half an hour because someone was working on my electrical stuff. After i turned it back on a saw a few lines on my monitor during windows 10 loading screen then they were gone. every since i cant get the 4 cards to work, i can load amd just fine, and nvidia separate, cant run both together in one instance of claymore miner.  every time i try and run them both it freezes and i got to restart. I even set the gtx clocks to default. Its god the new amd drivers and 15.2 or wherever the recommended drivers for nvidia.  It has been kind a hot in the room so for a day nvidia ran at 91, i figure its  ok for 2 days until ac is fixed.

   What are my options ?

My monitor goes through nvidia. Could it be bga ? but at 91 for a day ?? People claimed the ran for a week at 90......