Configuring new Antminer | Bitcointalksearch.org

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

Quote from: DonAlexio on April 12, 2019, 04:46:31 PM

Thank you so much! Now I can go on the webpage and I follow a video to basically configure it.
So can you help me to do it better please ?

The next thing you need to do is set the pool and ignore setting up the network setting just keep it in DHCP mode then reboot and start to run the miner.

If you can't still be satisfied you can check this (Review/Guide) Antminer S9 13.5 Th/s, 1320 W Bitcoin (SHA-256) ASIC miner

Quote from: DonAlexio on April 12, 2019, 04:46:31 PM

Hi,
Ok thank you I didn't know that!
And you were right, i didn't follow carefully how to reset and by your help I finally made it.
But I don't remember what I put on network setting

I'm glad that it fixed you don't need to put the network settings run now just ignore the remaining settings to DHCP.

DonAlexio

newbie

Activity: 12

Merit: 0

Thank you so much! Now I can go on the webpage and I follow a video to basically configure it.
So can you help me to do it better please ?
Thank you again!

I Took screeshot and I post it on this website :
http://zupimages.net/viewer.php?id=19/15/t0zn.png
http://zupimages.net/viewer.php?id=19/15/nwim.png
http://zupimages.net/viewer.php?id=19/15/iwz1.png
http://zupimages.net/viewer.php?id=19/15/y4ch.png

Quote from: BitMaxz on April 12, 2019, 04:40:46 PM

[...]

Hi,
Ok thank you I didn't know that!
And you were right, i didn't follow carefully how to reset and by your help I finally made it.
But I don't remember what I put on network setting.

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

Quote from: DonAlexio on April 12, 2019, 10:24:32 AM

I change the protocol on "static" but now I can't go on the IP address and my Antminer is in grey in "Advanced IP scanner" and "inactive" even if the green light on the machine is on.

Honestly, you don't need to change the protocol from DHCP to static you only need this if you are running multiple miners in the same network and if there is a miner with the same mac address with other devices connected to the same network you will experience some network issue but since you are beginner I think you are running only single miner?

If you can still remember what you put under static protocol you must post it here.

Code:

IP:
Netmask:
Gateway:
DNS Server:

I'm sure you didn't follow carefully how to reset the miner to the factory settings you don't need to follow the web GUI reset procedure what you need to do is to hard reset the miner through "reset button" or the "IP report button" make sure that you run the miner first for 10 minutes before you perform the hard reset.

mikeywith

legendary

Activity: 2436

Merit: 6643

be constructive or S.T.F.U

Quote from: DonAlexio on April 12, 2019, 01:00:08 PM

Yes I reset the antminer but the webpage still inaccessible. I can’t Go on this page even after reset the antminer
(Sorry for my English)

you need to use Advanced IP scanner again, because now your miner has a new IP address. if it does not appear, try to reset using reset method number 2.

DonAlexio

newbie

Activity: 12

Merit: 0

Yes I reset the antminer but the webpage still inaccessible. I can’t Go on this page even after reset the antminer
(Sorry for my English)

mikeywith

legendary

Activity: 2436

Merit: 6643

be constructive or S.T.F.U

you do not need to access the web page to reset the miner, simply find the small whole on the right side of the network port "reset", take a needle or something thin, insert it there for 5 seconds until the lights blink

there are other ways to reset too, but this is the easiest.

you can also go to this guide by bitmain to reset your miner > https://support.bitmain.com/hc/en-us/articles/115003595387-How-to-reset-miner-to-factory-settings-

after you have reset your miners, post the screenshot and i will guide you through it, it's pretty simple so don't panic.

DonAlexio

newbie

Activity: 12

Merit: 0

Hi mikeywith,
Thank you for your answer and for your help.
I try to reset but I can’t access to to website

mikeywith

legendary

Activity: 2436

Merit: 6643

be constructive or S.T.F.U

I know exactly what you did, you made a mistake in one of the network fields.

Do this

1- reset the miner ( google it )

2- go to your miner network setting and take a screenshot, post it here so someone can guide you on what to type in each filed.

Or see this https://bitcointalksearch.org/topic/if-your-miner-is-not-showing-on-the-network-here-is-what-you-doing-wrong-5094311.

DonAlexio

newbie

Activity: 12

Merit: 0

Hello,

I bought an Antminer S9 and I'm new with mining so I've got some problem to configure my Antminer.
I created an account on bitmain, next i found my IP adress on "Advanced IP scanner" and as the tutorial say I change the protocol on "static" but now I can't go on the IP adresse and my Antminer is in grey in "Advanced IP scanner" and "inactive" even if the green light on the machine is on.
Please help me and sorry for my english

Thank you

Topic: Configuring new Antminer (Read 215 times)