Topic: Ducting and Temp Control (Read 220 times)

Those temps are within what I would consider acceptable ranges for sure. Its 50f in the room I have mine in today and im seeing 46-50c PCB and 58-62c on the chips. On a hot day they run into the low 70s on the PCB at their hottest. If the weather will get warmer you might want to think of an exhaust, honestly a small fan in the roof just pulling a bit of air away should be plenty

Why do you need to construct tube directly to the miner? It's not necessary. Here is the simpler scheme for you room. Just put outlet vent in the upper part of the room
You also can calculate required outlet vent airflow if you know air temp at inlet with produced heat amount of 600W. Also inlet dimensions should not be less than outlet.

Thanks !
The Problem is that the duct that I will connect the output of the Y connector to , is 5" , the Solid duct is a bit larger , (not sure how much)  , but the connection towards that solid duct is only 5" , so I am afraid that even if I use a bigger duct (10") , there will be a "Bottleneck" at the solid duct entrance side , and creating a new vent is unfortunatley not an option in my flat

Also need to consider about the static pressure the 5" y splitter will create, and also those bends in the ducting. This will create alot of stress to the fans, might wear them out prematurely.

You are right , I did think about that , and I am not sure if I should do any extra work , or is the current setup OK.
Currently , with the false cieling tiles open and without any ducting or anything , I have the below Temps:
Max PCB Temp: around 50 C.
Max Chip Temp: around 78  C.
Fan Speed on both Miners : 3480 rpm

What do you think ?
Do you mind telling me a bit more about your setup and how is it holding up ?

I am planning to use the ducts as outlets to let the hot air exit the room , the flexible duct will connect the Y connector to the existing solid HVAC duct , for the intake , I will leave some of the false cieling tiles open , so that Air can flow in to the room , Air temp is around 25 C to 30 C this time of year.
Why do you think this will overheat the miners ? and what do you suggest instead ?

The most important thing when mining is just creating a airflow so the heated air would not stay for too long in the mining room. Your diagram seems like this could work .

Do you really need to do that much? z9 minis make almost no heat even when overclocked

Because the room is without AC unit it should create constant air circulation from the outside.
It could be passive inlet and active outlet. 5" (12 cm) outlet fan for 600W (2 Z9 mini) will be very noisy. If it's possible create bigger vent channel better to use 20cm outlet fan

Hello Miners !

I had to move my two Z9 Mini miners lately to a smaller room with no AC or Air Flow , and I am trying to find the best solution to cool and silence the miners as much as possible , I am in a bit of dilemma since I read and watched some conflicting advises about how to do proper ducting for your miners , so I would appreciate if you guys would weigh in and share your information , experinces and advises for my case.

The two Z9 mini's currently reside in a small room (1.5m x 4m) approximatley without AC , I am planning on connecting two 5" ducts to the two miners via 5" Fan Shrouds , combine these two ducts with a Y fitting connector , connect the Y connector to the exisitng HVAC system as shown in the diagram below:

https://ibb.co/fA4gHq

Will connecting the two Z9 mini miners to the same 5" duct (via the Y Connector) cause the miners to heat ?

Currently , I don't have any ducting , I just opened some of these false cieling tiles to allow the hot air to exit , and I can feel that this is working because the room temp. is cooler now , and the miners fans speed has dropped , howerver , I want to overclock the two miners and I want to know if ducting 1) will be much more effective 2) or just as good as opening these tiles ? 3) or if it will actually be worse than the current setup and cause the miners to overheat ?