Do you have a Solution for your Problem?
I've got 16 Blades, and since a couple of days, i've got exact the same problem.
The Proxy is jumping around from *.1 to *.2 - No matter what i change...
Topic: Erupter Blade - Repeatedly Switching Proxy (Read 2751 times)
Is there anyone that can help with this issue?
ok - thanks. I also have webEx - so I could let them direct me to places, but stay in control.
Happy to start up a Team Viewer Session if anyone is interested in poking around.
That can be dangerous. Make sure you are fully aware of what the other party is doing and don't let them execute unknown commands. Be ready to disconnect if necessary.
Re-Post from Newbie section:
Firstly, I searched every article I could on this forum and couldn't find a solution. I then spoke for hours in Slush's IRC chat to no avail.
After hours of troubleshooting I'm still having the same problem, though I have a lot more detail on what is happening. In a nutshell the blades continuously switch between the listed Server Addresses.
I have Slush's mining_proxy.exe configured on two local computers - both desktops, both configured not to Sleep.
Total MHS: 05121
Received: 0000062580
Accepted: 0000040226
Per Minute: 070.82
Efficiency: 064.27%
Up Time: 0d,09h,28m,00s
Current Server: 10.1.10.11:8332
Chip: OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
IP: 10.1.10.54
Mask: 255.255.255.0
Gateway: 10.1.10.1
WEB Port: 80
Primary DNS: 10.1.10.1
Secondary DNS: 10.1.10.1
Ports : 8332,8332
Server addresses : 10.1.10.11,10.1.10.10
user:pass : Any.worker1:xxxxxx,Any.worker1:xxxxxx
I have 10 blades on a backplane with an HP ATSN 7001044-Y000 979124-001 Power Supply, all of them act identical. They act the same weather I have 1 blade connected to the backplane or all 10.
I have tested switching out the proxy for 32bit bfgminer, linux bfgminer on a BBB, and different proxy software on each computer.
The voltage reads 12.81v, however I have not tested amperage as I'm not familiar enough with electricity to tinker that deep.
The blades to NOT restart - they just switch between the two servers (proxies) and remain around 5000 mh/s.
If I configure the blades with the same server separated by commas (e.g. 10.1.10.11,10.1.10.11), the blades will continuously reset after just over 2 minutes.
Happy to start up a Team Viewer Session if anyone is interested in poking around.
Many thanks to dmelvin, minigpenguin, MoonCat, bitguy, urgodfather, and honkeylips for helping me get this far.
New Info: I appears that one of the proxy servers does in fact go into hibernation. When this happens the the blade does process on the primary proxy and appears to stay at around 9800mhs. But again, if I start the place with the same server proxy IP listed twice, the blade just restarts over and over after a couple minutes.
Firstly, I searched every article I could on this forum and couldn't find a solution. I then spoke for hours in Slush's IRC chat to no avail.
After hours of troubleshooting I'm still having the same problem, though I have a lot more detail on what is happening. In a nutshell the blades continuously switch between the listed Server Addresses.
I have Slush's mining_proxy.exe configured on two local computers - both desktops, both configured not to Sleep.
Total MHS: 05121
Received: 0000062580
Accepted: 0000040226
Per Minute: 070.82
Efficiency: 064.27%
Up Time: 0d,09h,28m,00s
Current Server: 10.1.10.11:8332
Chip: OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO
IP: 10.1.10.54
Mask: 255.255.255.0
Gateway: 10.1.10.1
WEB Port: 80
Primary DNS: 10.1.10.1
Secondary DNS: 10.1.10.1
Ports : 8332,8332
Server addresses : 10.1.10.11,10.1.10.10
user:pass : Any.worker1:xxxxxx,Any.worker1:xxxxxx
I have 10 blades on a backplane with an HP ATSN 7001044-Y000 979124-001 Power Supply, all of them act identical. They act the same weather I have 1 blade connected to the backplane or all 10.
I have tested switching out the proxy for 32bit bfgminer, linux bfgminer on a BBB, and different proxy software on each computer.
The voltage reads 12.81v, however I have not tested amperage as I'm not familiar enough with electricity to tinker that deep.
The blades to NOT restart - they just switch between the two servers (proxies) and remain around 5000 mh/s.
If I configure the blades with the same server separated by commas (e.g. 10.1.10.11,10.1.10.11), the blades will continuously reset after just over 2 minutes.
Happy to start up a Team Viewer Session if anyone is interested in poking around.
Many thanks to dmelvin, minigpenguin, MoonCat, bitguy, urgodfather, and honkeylips for helping me get this far.
New Info: I appears that one of the proxy servers does in fact go into hibernation. When this happens the the blade does process on the primary proxy and appears to stay at around 9800mhs. But again, if I start the place with the same server proxy IP listed twice, the blade just restarts over and over after a couple minutes.
Jump to: