Tengo un Antminer S9 13,5 T y desde hace unos dias ha dejado de funcionar.
Describo a continuacion el problema con la mayor cantidad de informacion posible.
El equipo presenta los siguientes sintomas:
(No se si hubo algun fallo electrico, estaba bien revise antes de salir, al llegar estaba asi)
1.- Las luces delanteras correspondientes (Roja) Fault y (Verde) Normal , no encienden ninguna de las dos.
2.- Las luces Verdes de la controladora encienden las 3, una de ellas titila.
3.- Las luces rojas de las HashBoards tienen el siguiente comportamiento.
a.- Aveces enciende una sola y queda encendida.
b.- Aveces encienden las 3 y quedan encendidas, cuando hago un reset (aveces no encienden)
c.- Aveces no enciende ninguna de las 3.
d.- Aveces enciende una y a los pocos segundos se apaga.
4.- Si Puedo acceder al sistema del minero con el navegador sin problemas con su ip, una vez dentro del sistema ocurre esto:
a.- En la pestaña Overview, Hardware Version y BBMiner Version estan en blanco, es decir no dice nada.
b.- En la pestaña Status, todo esta en blanco, no hay informacion.
5.- El minero al encenderlo la luz roja prende por un instante muy corto, diria milisegundos.
6.- Los ventiladores parecen funcionar a velocidad normal por lo menos no se aprecia ningun detalle.
Describo a continuacion las puebas que he hecho:
1.- He probado la funte de poder con multimetro y todos los terminales dan 12,25 voltios, parece estar bien.
2.- He reseteado la maquina de tres formas diferentes.
a.- Con el boton de reset.
b.- Desde el navegador entrando al sistema, pestaña upgrade>reset.
c.- Con el boton de ip Report, con la maquina apagada presiono el boton al mismo tiempo la enciendo y lo dejo rpesionado por 5 segundos.
Con este ultimo procedimiendo a veces encienden las 3 luces de las hasboards.
3.- Desconecte todos los cables, de la fuente, los ventiladores y los cables de datos de la controladora a la hashBoards. deje un rato y volvi a conectar.
4.- Probe conectando las hashBoards individualmente una por una.
5.- Probe usando otra acometida electrica, (Uso 220v), tambien probe un protector electrico diferente. La acometida entrega a la fuente de poder (227 - 230v)
6.- Como ultima opcion he actualizado el firmware, he descargado desde la pagina oficial de bitmain Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz
El proceso de actualizacion se realizo sin ningun problema, lo hizo perfecto, sin embargo el equipo quedo exactamente igual sin ningun cambio.
Acontinuacion dejo algunas imagenes realcionadas a la falla:
Trajeta Controladora:
https://imguh.com/image/8Ap0Q
Panel Delantero
https://imguh.com/image/8AEgM
HashBoards
https://imguh.com/image/8AgCz
Status:
https://imguh.com/image/8A6lZ
Overview.
https://imguh.com/image/8AYMX
Entonces:
Bueno no me queda mas que recurrir a los expertos en estos temas para que me puedan orientar de acuerdo a sus conocimietos y experiencias de fallas parecidas.
Tambien dejo el Kernel Log:
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-ge8a2f71-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #82 SMP PREEMPT Tue May 16 19:49:53 CST 2017
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 16800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 126976
[ 0.000000] free_area_init_node: node 0, pgdat c0740a40, node_mem_map debd8000
[ 0.000000] Normal zone: 992 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 126976 pages, LIFO batch:31
[ 0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc:
- 0
- 1
[ 0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 364356K/507904K available (5032K kernel code, 283K rwdata, 1916K rodata, 204K init, 258K bss, 143548K reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06d1374 (6949 kB)
[ 0.000000] .init : 0xc06d2000 - 0xc0705380 ( 205 kB)
[ 0.000000] .data : 0xc0706000 - 0xc074cf78 ( 284 kB)
[ 0.000000] .bss : 0xc074cf84 - 0xc078d9fc ( 259 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to df802000
[ 0.000000] zynq_clock_init: clkc starts at df802100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000310] ps7-ttc #0 at df804000, irq=43
[ 0.000615] Console: colour dummy device 80x30
[ 0.000647] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040209] pid_max: default: 32768 minimum: 301
[ 0.040429] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.040449] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.042577] CPU: Testing write buffer coherency: ok
[ 0.042909] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042968] Setting up static identity map for 0x4c4b00 - 0x4c4b58
[ 0.043195] L310 cache controller enabled
[ 0.043215] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121034] CPU1: Booted secondary processor
[ 0.210229] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210359] Brought up 2 CPUs
[ 0.210379] SMP: Total of 2 processors activated.
[ 0.210387] CPU: All CPU(s) started in SVC mode.
[ 0.211049] devtmpfs: initialized
[ 0.213464] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214677] regulator-dummy: no parameters
[ 0.222358] NET: Registered protocol family 16
[ 0.224643] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226939] cpuidle: using governor ladder
[ 0.226952] cpuidle: using governor menu
[ 0.234390] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235915] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235929] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.236044] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[ 0.257608] bio: create slab
[ 0.259032] vgaarb: loaded
[ 0.259751] SCSI subsystem initialized
[ 0.260795] usbcore: registered new interface driver usbfs
[ 0.260966] usbcore: registered new interface driver hub
[ 0.261322] usbcore: registered new device driver usb
[ 0.261848] media: Linux media interface: v0.10
[ 0.262006] Linux video capture interface: v2.00
[ 0.262244] pps_core: LinuxPPS API ver. 1 registered
[ 0.262256] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.262384] PTP clock support registered
[ 0.262743] EDAC MC: Ver: 3.0.0
[ 0.263795] Advanced Linux Sound Architecture Driver Initialized.
[ 0.266642] DMA-API: preallocated 4096 debug entries
[ 0.266656] DMA-API: debugging enabled by kernel config
[ 0.266732] Switched to clocksource arm_global_timer
[ 0.287600] NET: Registered protocol family 2
[ 0.288257] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.288314] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.288399] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.288442] TCP: reno registered
[ 0.288460] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288492] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.288728] NET: Registered protocol family 1
[ 0.289072] RPC: Registered named UNIX socket transport module.
[ 0.289084] RPC: Registered udp transport module.
[ 0.289093] RPC: Registered tcp transport module.
[ 0.289101] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.289114] PCI: CLS 0 bytes, default 64
[ 0.289555] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.291559] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.293662] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.293862] msgmni has been set to 967
[ 0.294637] io scheduler noop registered
[ 0.294649] io scheduler deadline registered
[ 0.294687] io scheduler cfq registered (default)
[ 0.309791] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.309812] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.432094] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.000350] console [ttyPS0] enabled
[ 1.004623] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[ 1.012261] [drm] Initialized drm 1.1.0 20060810
[ 1.029390] brd: module loaded
[ 1.038770] loop: module loaded
[ 1.048567] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.054312] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.062248] libphy: XEMACPS mii bus: probed
[ 1.066621] ------------- phy_id = 0x3625e62
[ 1.071520] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.080129] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.086777] ehci-pci: EHCI PCI platform driver
[ 1.093985] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.100820] usbcore: registered new interface driver usb-storage
[ 1.107686] mousedev: PS/2 mouse device common for all mice
[ 1.113780] i2c /dev entries driver
[ 1.120758] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.126242] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.132154] Xilinx Zynq CpuIdle Driver started
[ 1.137055] sdhci: Secure Digital Host Controller Interface driver
[ 1.143152] sdhci: Copyright(c) Pierre Ossman
[ 1.147580] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.153312] mmc0: no vqmmc regulator found
[ 1.157362] mmc0: no vmmc regulator found
[ 1.196749] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.205427] usbcore: registered new interface driver usbhid
[ 1.210945] usbhid: USB HID core driver
[ 1.215666] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.221964] nand: Micron MT29F2G08ABAEAWP
[ 1.225928] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.231866] Bad block table found at page 131008, version 0x01
[ 1.238086] Bad block table found at page 130944, version 0x01
[ 1.244137] 3 ofpart partitions found on MTD device pl353-nand
[ 1.249920] Creating 3 MTD partitions on "pl353-nand":
[ 1.255010] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.263068] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.270390] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[ 1.279358] TCP: cubic registered
[ 1.282591] NET: Registered protocol family 17
[ 1.287305] Registering SWP/SWPB emulation handler
[ 1.293186] regulator-dummy: disabling
[ 1.297509] UBI: attaching mtd1 to ubi0
[ 1.605773] UBI: scanning is finished
[ 1.626285] UBI: volume 0 ("rootfs") re-sized from 192 to 1108 LEBs
[ 1.633411] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[ 1.640493] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 1.647255] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 1.653920] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 1.660798] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[ 1.666778] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[ 1.673886] UBI: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1134783803
[ 1.682928] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[ 1.692144] UBI: background thread "ubi_bgt0d" started, PID 1080
[ 1.692150] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.696052] ALSA device list:
[ 1.696055] No soundcards found.
[ 1.714656] UBIFS: background thread "ubifs_bgt0_0" started, PID 1082
[ 1.786778] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[ 1.792705] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 1.801836] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[ 1.811723] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.816762] UBIFS: media format: w4/r0 (latest is w4/r0), UUID B079DD56-06BB-4E31-8F5E-A6604F480DB2, small LPT model
[ 1.838261] VFS: Mounted root (ubifs filesystem) on device 0:11.
[ 1.980840] devtmpfs: mounted
[ 1.983946] Freeing unused kernel memory: 204K (c06d2000 - c0705000)
[ 3.316456] random: dd urandom read with 0 bits of entropy available
[ 3.936774]
[ 3.936774] bcm54xx_config_init
[ 4.716749]
[ 4.716749] bcm54xx_config_init
[ 7.717614] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 7.723702] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 21.871123] In axi fpga driver!
[ 21.874193] request_mem_region OK!
[ 21.877620] AXI fpga dev virtual address is 0xdf9fc000
[ 21.882691] *base_vir_addr = 0x8c510
[ 21.898476] In fpga mem driver!
[ 21.901544] request_mem_region OK!
[ 21.905105] fpga mem virtual address is 0xe2000000
[ 22.686775]
[ 22.686775] bcm54xx_config_init
[ 23.316782]
[ 23.316782] bcm54xx_config_init
[ 26.317607] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[ 26.323629] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[ 701.334814] random: nonblocking pool is initialized
This is XILINX board. Totalram: 507527168
Detect 512MB control board of XILINX
DETECT HW version=0008c510
miner ID : 8158ed0e7680881c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
set_reset_allhashboard = 0x0000ffff
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[1] has core num=1
Chain[5] ASIC[2] has core num=1
Chain[5] ASIC[3] has core num=1
Chain[5] ASIC[4] has core num=1
Chain[5] ASIC[7] has core num=1
Chain[5] ASIC[8] has core num=1
Chain[5] ASIC[9] has core num=1
Chain[5] ASIC[10] has core num=1
Chain[5] ASIC[11] has core num=1
Chain[5] ASIC[12] has core num=1
Chain[5] ASIC[13] has core num=1
Chain[5] ASIC[14] has core num=1
Chain[5] ASIC[15] has core num=3
Chain[5] ASIC[17] has core num=1
Chain[5] ASIC[18] has core num=1
Chain[5] ASIC[20] has core num=5
Chain[5] ASIC[21] has core num=2
Chain[5] ASIC[22] has core num=1
Chain[5] ASIC[23] has core num=1
Chain[5] ASIC[24] has core num=1
Chain[5] ASIC[25] has core num=1
Chain[5] ASIC[26] has core num=2
Chain[5] ASIC[27] has core num=1
Chain[5] ASIC[28] has core num=1
Chain[5] ASIC[29] has core num=1
Chain[5] ASIC[30] has core num=1
Chain[5] ASIC[31] has core num=1
Chain[5] ASIC[32] has core num=2
Chain[5] ASIC[33] has core num=1
Chain[5] ASIC[34] has core num=1
Chain[5] ASIC[36] has core num=1
Chain[5] ASIC[37] has core num=1
Chain[5] ASIC[38] has core num=2
Chain[5] ASIC[39] has core num=1
Chain[5] ASIC[40] has core num=2
Chain[5] ASIC[41] has core num=1
Chain[5] ASIC[42] has core num=1
Chain[5] ASIC[43] has core num=1
Chain[5] ASIC[44] has core num=1
Chain[5] ASIC[45] has core num=2
Chain[5] ASIC[47] has core num=1
Chain[5] ASIC[48] has core num=2
Chain[5] ASIC[49] has core num=1
Chain[5] ASIC[50] has core num=1
Chain[5] ASIC[51] has core num=1
Chain[5] ASIC[52] has core num=1
Chain[5] ASIC[53] has core num=1
Chain[5] ASIC[54] has core num=1
Chain[5] ASIC[55] has core num=2
Chain[5] ASIC[56] has core num=2
Chain[5] ASIC[57] has core num=1
Chain[5] ASIC[59] has core num=1
Chain[5] ASIC[61] has core num=1
Chain[5] ASIC[62] has core num=1
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[0] has core num=1
Chain[6] ASIC[1] has core num=1
Chain[6] ASIC[2] has core num=1
Chain[6] ASIC[5] has core num=1
Chain[6] ASIC[8] has core num=1
Chain[6] ASIC[11] has core num=1
Chain[6] ASIC[14] has core num=1
Chain[6] ASIC[16] has core num=2
Chain[6] ASIC[17] has core num=2
Chain[6] ASIC[19] has core num=2
Chain[6] ASIC[20] has core num=1
Chain[6] ASIC[23] has core num=1
Chain[6] ASIC[26] has core num=1
Chain[6] ASIC[32] has core num=1
Chain[6] ASIC[35] has core num=1
Chain[6] ASIC[38] has core num=1
Chain[6] ASIC[41] has core num=1
Chain[6] ASIC[44] has core num=2
Chain[6] ASIC[47] has core num=1
Chain[6] ASIC[50] has core num=1
Chain[6] ASIC[51] has core num=3
Chain[6] ASIC[52] has core num=2
Chain[6] ASIC[53] has core num=1
Chain[6] ASIC[54] has core num=1
Chain[6] ASIC[55] has core num=1
Chain[6] ASIC[56] has core num=1
Chain[6] ASIC[57] has core num=1
Chain[6] ASIC[58] has core num=1
Chain[6] ASIC[59] has core num=1
Chain[6] ASIC[60] has core num=1
Chain[6] ASIC[61] has core num=3
Chain[6] ASIC[62] has core num=1
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[26] has core num=1
Chain[7] ASIC[34] has core num=1
Check chain[7] PIC fw version=0x03
get PIC voltage=125 on chain[5], value=870
get PIC voltage=125 on chain[6], value=870
get PIC voltage=125 on chain[7], value=870
set_reset_allhashboard = 0x00000000
chain[5] temp offset record: 62,-2,0,0,0,0,33,0
chain[5] temp chip I2C addr=0x98
chain[6] temp offset record: 62,-4,0,0,0,0,33,0
chain[6] temp chip I2C addr=0x98
chain[7] temp offset record: 62,-5,0,0,0,0,33,0
chain[7] temp chip I2C addr=0x98
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
CRC error counter=0
set command mode to VIL
--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
search freq for 1 times, completed chain = 3, total chain num = 3
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found= 1495 root 0:00 grep bmminer
bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Fri Nov 17 17:57:49 CST 2017 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 8158ed0e7680881c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[2] speed=4560
get fan[4] speed=960
get fan[2] speed=4560
get fan[4] speed=960
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=1920
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
get fan[2] speed=4560
get fan[4] speed=960
get fan[5] speed=2040
Fatal Error: some Fan lost or Fan speed low!
Aqui en la ultima linea del Log parece haber un problema con un ventilador, en tal caso, como puedo probarlos porque
aparentemente funcionan bien como siempre.
Estare agradecido me puedan ayudar a diagnosticar el problema.
Gracias y saludos a todos.