Author

Topic: graphics card in PCI x1 (Read 950 times)

sr. member
Activity: 547
Merit: 253
June 25, 2011, 06:47:03 PM
#10
I have nine 6950s on three total rigs (three each) and they are all connected via dual cross-fire cables. So no additional external monitors or dummy plugs are needed.

I thought this was a good design to save on monitor costs.

Ya but really your losing hashs by running them crossfire, ur better off with dummy's.
legendary
Activity: 2492
Merit: 1473
LEALANA Bitcoin Grim Reaper
June 25, 2011, 06:38:20 PM
#9
I have nine 6950s on three total rigs (three each) and they are all connected via dual cross-fire cables. So no additional external monitors or dummy plugs are needed.

I thought this was a good design to save on monitor costs.
newbie
Activity: 15
Merit: 0
June 25, 2011, 04:45:20 PM
#8
wouldnt be doing all this right now....if i could have got linux coin going
newbie
Activity: 15
Merit: 0
June 25, 2011, 04:43:03 PM
#7
yes i turned on the monitor.....it only shows orange light...screen wont come on

also it still no showing up in my device manager

i restarted cleaned it out....the fan is still running non stop
member
Activity: 119
Merit: 10
June 25, 2011, 04:30:46 PM
#6
Did you turn on the old monitor? You can't just leave it off otherwise the circuit is not complete. Think about it for a second. It's like you screwed in a light bulb and expect it to turn on without flipping the switch.


P.S: Another thing you can do is start the mining software with the primary card hooked up to your main monitor, then switch that primary monitor to the secondary card and it should detect it.
newbie
Activity: 15
Merit: 0
June 25, 2011, 04:00:40 PM
#5
ok so hook up an old monitor i had but nothing...downloaded and installed drivers for just incase but still nothing....althought the fan on it is running non stop and fast....does that mean anything.....


as far as the connection goes i can take it out again....but i made sure and cleaned as much of it as i could
full member
Activity: 148
Merit: 100
June 25, 2011, 03:51:50 PM
#4
I've been using dremeled 1x extenders and here is my experience:

on an older motherboard (asus p5k deluxe) none of the cards were detected.  

on my miner with a newer mobo (asrock something) one card was detected right away and the other one I had to reseat several times and restart the computer each time before it finally recognized the card attached.  Im afraid to move that card/extender because it might sever the connection.

so check the connection, or maybe it's a motherboard problem.  You do need a dummy plug or you can make your own with resistors, but even without a plug, the device should show in device manager.
newbie
Activity: 15
Merit: 0
June 25, 2011, 03:48:51 PM
#3
ok cool...i had heard about those...dont have any resistors yet i will hook a monitor to it real quick...
member
Activity: 119
Merit: 10
June 25, 2011, 03:46:19 PM
#2
The secondary card needs to be hooked up to a display or a dummy plug, otherwise the graphics driver will not initialize it.
newbie
Activity: 15
Merit: 0
June 25, 2011, 03:30:57 PM
#1
 I had heard that you could fit a PCI x16 card into the PCI x1 slot.....i know most poeple use any exterder but i dont have one yet....so i looked it up all you had to do was have alittle fun with the drimel tool and it would fit....

so i did that....i have a 5830 in the 16 slot....and a 5770 in the x1 slot....but its not showing up my device manager ....or in guiminer....

is there something i have to do to make it see the card....

the 5770 is just to mine of course



i know this is more of a tech problem...but can only post here
Jump to: