The "Blades" actually were 2 40-chip units, not a single 80 chip - so chips=40 would be correct.
They hashed in the rough ballpark of 2.6 Mhash/sec (a little over as I recall) at their "stock" 700 Mhz setting.
Topic: Gridseed blade 80 chip scrypt miner - what are these errors? (Read 300 times)
I haven't run one of these in a while but I am pretty sure the chip=xx is telling the software how many chips you have so it needs to equal what the blade actually has which according to your subject is 80.
freq at 850 is probably causing you a LOT of hardware errors.
Those miners were "stock" at 700 but THAT was already a fairly hefty overclock, and tended to overstress the power delivery system.
Those miners were "stock" at 700 but THAT was already a fairly hefty overclock, and tended to overstress the power delivery system.
That was very helpful thank you! I'd hate to burn those chips out.
freq at 850 is probably causing you a LOT of hardware errors.
Those miners were "stock" at 700 but THAT was already a fairly hefty overclock, and tended to overstress the power delivery system.
Those miners were "stock" at 700 but THAT was already a fairly hefty overclock, and tended to overstress the power delivery system.
Hello everyone, I just got my first ASIC miner yesterday. A little used but its hashing steady at 5.692Mh/s on avg. I solo mined with it for a couple of hours this morning and hit one altcoin twice. 
I've been running it in a pool and payments are coming in steady so everything seems great. But under the hood I keep seeing these errors and I can' figure out what they mean. Would someone be kind enough to explain these errors?
[2017-10-08 18:12:21] < (no data)
[2017-10-08 18:12:21] GSD0: GetResults (amt=0 err=-7 ern=0)
[2017-10-08 18:12:21] < (no data)
[2017-10-08 18:12:21] [thread 0: 621954 hashes, 2.8 mhash/sec]
[2017-10-08 18:12:22] GSD1: GetResults (amt=0 err=-7 ern=0)
[2017-10-08 18:12:22] < (no data)
[2017-10-08 18:12:22] [thread 1: 630501 hashes, 2.9 mhash/sec]
[2017-10-08 18:12:22] GSD0: GetResults (amt=0 err=-7 ern=0)
[2017-10-08 18:12:22] < (no data)
I also use this command to start the blade: cgminer --scrypt -o stratum+tcp://miningpool.thruhere.net:7998/#xnsub -u KSDDbiASUGSIdfouAhfohufchoduhvosdvh -p x --gridseed-options=baud=115200,freq=850,chips=40 --hotplug 80
I'm not sure if chips=40 should be set at 40 or 80. I tried it at chips=80 and it hashed just fine at 11.5Mh/s but I worried it might burnout the chip.
I'm also not sure if the --hotplug should be changed from 80 to something else. Any suggestions?
Thanks in advance for any help...
I've been running it in a pool and payments are coming in steady so everything seems great. But under the hood I keep seeing these errors and I can' figure out what they mean. Would someone be kind enough to explain these errors? [2017-10-08 18:12:21] < (no data)
[2017-10-08 18:12:21] GSD0: GetResults (amt=0 err=-7 ern=0)
[2017-10-08 18:12:21] < (no data)
[2017-10-08 18:12:21] [thread 0: 621954 hashes, 2.8 mhash/sec]
[2017-10-08 18:12:22] GSD1: GetResults (amt=0 err=-7 ern=0)
[2017-10-08 18:12:22] < (no data)
[2017-10-08 18:12:22] [thread 1: 630501 hashes, 2.9 mhash/sec]
[2017-10-08 18:12:22] GSD0: GetResults (amt=0 err=-7 ern=0)
[2017-10-08 18:12:22] < (no data)
I also use this command to start the blade: cgminer --scrypt -o stratum+tcp://miningpool.thruhere.net:7998/#xnsub -u KSDDbiASUGSIdfouAhfohufchoduhvosdvh -p x --gridseed-options=baud=115200,freq=850,chips=40 --hotplug 80
I'm not sure if chips=40 should be set at 40 or 80. I tried it at chips=80 and it hashed just fine at 11.5Mh/s but I worried it might burnout the chip.
I'm also not sure if the --hotplug should be changed from 80 to something else. Any suggestions?
Thanks in advance for any help...
Jump to: