Topic: HELP: {AntMiner S1} TOO High HW error (Read 977 times)
Try to do an hard reset, i had the same problem with an ant, and after a complete reset it turned again extremely low HW error count (1-2 per day).
Enhance heat dissipation, replace the power supply, which is the only thing you can do, in fact, you can improve performance by overclocking to make up part of HW
Do I need to replace my 750w PSU even though kill-a-watt reads at 376w only? I won't OC for I'm in a testmode so far, also don't want to void my warranty.
I didn't touch anything & it's in stock settings.
My PSU is CS750M & only mined 0.0093btc @ multipool.us
Any recommended pools?
TIA for the help.
My PSU is CS750M & only mined 0.0093btc @ multipool.us
Any recommended pools?
TIA for the help.
dont use multipool.us they have big mining fee
use eligius.st, ghash.io, polmine.pl or other one with small fee and merge mining coins
Thanks for the tips, I'll try to look for those pools.
That's a 0.34% HW rate. It's nothing.
Did you re-tighten the heat sinks?
Did you re-check the power supply?
Just enjoy the 0.0012 btc your S1 is bringing you every day.
Did you re-tighten the heat sinks?
Did you re-check the power supply?
Just enjoy the 0.0012 btc your S1 is bringing you every day.
0.012 BTC you mean?
Enhance heat dissipation, replace the power supply, which is the only thing you can do, in fact, you can improve performance by overclocking to make up part of HW
I didn't touch anything & it's in stock settings.
My PSU is CS750M & only mined 0.0093btc @ multipool.us
Any recommended pools?
TIA for the help.
My PSU is CS750M & only mined 0.0093btc @ multipool.us
Any recommended pools?
TIA for the help.
dont use multipool.us they have big mining fee
use eligius.st, ghash.io, polmine.pl or other one with small fee and merge mining coins
I didn't touch anything & it's in stock settings.
My PSU is CS750M & only mined 0.0093btc @ multipool.us
Any recommended pools?
TIA for the help.
My PSU is CS750M & only mined 0.0093btc @ multipool.us
Any recommended pools?
TIA for the help.
That's a 0.34% HW rate. It's nothing.
Did you re-tighten the heat sinks?
Did you re-check the power supply?
Just enjoy the 0.0012 btc your S1 is bringing you every day.
Did you re-tighten the heat sinks?
Did you re-check the power supply?
Just enjoy the 0.0012 btc your S1 is bringing you every day.
Good day to all miners,
I purchased my first AntMiner S1 & got it work smoothly but my problem is I'm having a too high HW & more rejections.
http://s27.postimg.org/51l6cu5yb/Ant_Miner_HW.png
Is this normal? or I'm having a misconfiguration? Any suggestions to lower my HW ratio?
I've been searching for same topic & found out simon66 post is much better than my problem.
https://bitcointalksearch.org/topic/antminer-s1-high-hw-error-537685
Thanks a lot.
I purchased my first AntMiner S1 & got it work smoothly but my problem is I'm having a too high HW & more rejections.
http://s27.postimg.org/51l6cu5yb/Ant_Miner_HW.png
Is this normal? or I'm having a misconfiguration? Any suggestions to lower my HW ratio?
I've been searching for same topic & found out simon66 post is much better than my problem.
https://bitcointalksearch.org/topic/antminer-s1-high-hw-error-537685
Thanks a lot.
Jump to: