Help needed with use of 1x slot to add third 5830 in LinuxCoin

Crypt_Current

hero member

Activity: 686

Merit: 500

Shame on everything; regret nothing.

Quote from: jjiimm_64 on October 20, 2011, 08:54:16 PM

Quote from: Crypt_Current on October 06, 2011, 03:56:59 PM

I just tried to use the pci-e 1x for another 5830 in my 2x5830 rig using a 1x to 16x cable (which would make it into a 3x5830 rig).
I had partial luck...
The rig runs LinuxCoin. What happened was "aticonfig --lsa" listed all three devices, but "AMDOverdriveCtrl -h" only listed the ones plugged into 16x slots, even though it had a couple more entries in its table than usual.

When I tried to run phoenix miner on the DEVICE 2 that "aticonfig --lsa" listed, it tried to use the CPU... Angry

If anyone could help me with my particular LinuxCoin issue, that'd be great!

It's not much, but I can offer 0.5 BTC for a complete solution.

if aticonfig sees the card, I think it is initialized OK. try a different miner. I use cgminer, which would also negate your need for amdoverdirve too. cgminer will clock and fan control your cards.

Hmm thanks, I'll give that a go and post results :-)

jjiimm_64

legendary

Activity: 1876

Merit: 1000

Quote from: Crypt_Current on October 06, 2011, 03:56:59 PM

I just tried to use the pci-e 1x for another 5830 in my 2x5830 rig using a 1x to 16x cable (which would make it into a 3x5830 rig).
I had partial luck...
The rig runs LinuxCoin. What happened was "aticonfig --lsa" listed all three devices, but "AMDOverdriveCtrl -h" only listed the ones plugged into 16x slots, even though it had a couple more entries in its table than usual.

When I tried to run phoenix miner on the DEVICE 2 that "aticonfig --lsa" listed, it tried to use the CPU... Angry

If anyone could help me with my particular LinuxCoin issue, that'd be great!

It's not much, but I can offer 0.5 BTC for a complete solution.

if aticonfig sees the card, I think it is initialized OK. try a different miner. I use cgminer, which would also negate your need for amdoverdirve too. cgminer will clock and fan control your cards.

DeathAndTaxes

donator

Activity: 1218

Merit: 1079

Gerald Davis

Quote from: Crypt_Current on October 17, 2011, 11:55:58 AM

Forgive my being naive, but how exactly would I go about doing that?

Get a piece of insulated wire, strip the ends of it. Connect exactly those two pins in the slot. Don't misconnect it or your card and/or MB can go poof.

Crypt_Current

hero member

Activity: 686

Merit: 500

Shame on everything; regret nothing.

Forgive my being naive, but how exactly would I go about doing that?

d.james

sr. member

Activity: 280

Merit: 250

Firstbits: 12pqwk

I think what you need to do is this:
connect these 2 pins on your 1X adapter, your 2nd gpu shall be properly initialized.

Crypt_Current

hero member

Activity: 686

Merit: 500

Shame on everything; regret nothing.

I just tried to use the pci-e 1x for another 5830 in my 2x5830 rig using a 1x to 16x cable (which would make it into a 3x5830 rig).
I had partial luck...
The rig runs LinuxCoin. What happened was "aticonfig --lsa" listed all three devices, but "AMDOverdriveCtrl -h" only listed the ones plugged into 16x slots, even though it had a couple more entries in its table than usual.

When I tried to run phoenix miner on the DEVICE 2 that "aticonfig --lsa" listed, it tried to use the CPU... Angry

If anyone could help me with my particular LinuxCoin issue, that'd be great!

It's not much, but I can offer 0.5 BTC for a complete solution.

Topic: Help needed with use of 1x slot to add third 5830 in LinuxCoin (Read 1464 times)