how do I wire 2 block erupter cubes to a single supply

Meech

hero member

Activity: 924

Merit: 1000

Quote from: sandman102 on April 25, 2014, 11:38:15 AM

I was planning on using a old xp box thats just sitting around and mining-proxy. What are the advantages to using the pi?

Thanks

Sandman102

The mining proxy is super easy to use but is limited in the info it gives. You can use either 1 cable with 2 6 pin connectors or 2 cables with 1 6 pin connector for each unit.

Chris_Sabian

legendary

Activity: 896

Merit: 1001

Quote from: sandman102 on April 25, 2014, 11:38:15 AM

I was planning on using a old xp box thats just sitting around and mining-proxy. What are the advantages to using the pi?

Thanks

Sandman102

Uses less power (something like 10 watts) than computer (100-500 watts).

sandman102

newbie

Activity: 6

Merit: 0

I was planning on using a old xp box thats just sitting around and mining-proxy. What are the advantages to using the pi?

Thanks

Sandman102

Chris_Sabian

legendary

Activity: 896

Merit: 1001

Also, if you wanted to use a raspberry pi as the proxy and bfgminer here is the code:

sudo apt-get update
sudo apt-get install autoconf automake libtool pkg-config libcurl4-gnutls-dev libjansson-dev uthash-dev libmicrohttpd-dev unzip
wget http://luke.dashjr.org/programs/bitcoin/files/bfgminer/3.8.0/bfgminer-3.8.0.zip
unzip bfgminer-3.8.0.zip
cd bfgminer-3.8.0
./configure
make
make install
./bfgminer -o pool -O user:pass --http-port 8330

**replace pool and user:pass as necessary**
Example ./bfgminer -o stratum.btcguild.com:3333 -O minerguy_1:12345 --http-port 8330

Chris_Sabian

legendary

Activity: 896

Merit: 1001

Quote from: sandman102 on April 25, 2014, 10:38:00 AM

My power supply comes with 4 6+2 PCI cables, am I correct in assuming that each erupter requires 2 separate cables?

The reason I ask is because on each of my cables, there are are 2 6 pin connectors at the end of each of cables. Am I correct in assuming that I use 2 cables for each erupter, and not use the second connecter on the cable?

Thanks

Sandman

You can go either way. Ideally you would use 2 cables though.

I have a cube running with 2 cables and I have another cube running with 1 cable - 2 connectors (each cable has 2 connectors for power)

sandman102

newbie

Activity: 6

Merit: 0

My power supply comes with 4 6+2 PCI cables, am I correct in assuming that each erupter requires 2 separate cables?

The reason I ask is because on each of my cables, there are are 2 6 pin connectors at the end of each of cables. Am I correct in assuming that I use 2 cables for each erupter, and not use the second connecter on the cable?

Thanks

Sandman

Chris_Sabian

legendary

Activity: 896

Merit: 1001

Quote from: cinnamon_carter on April 24, 2014, 09:54:22 PM

i don't have one but i have seen some impressive set up's with a raspberry pi running a load of these, ( i have raspberry pi not eruptors !)

I have a raspberry pi acting as a proxy and running bfgminer with several cubes. I have been running it for months. No problems other than the very very intermittent bfgminer crash/restart

cinnamon_carter

legendary

Activity: 1148

Merit: 1018

It's about time -- All merrit accepted !!!

i don't have one but i have seen some impressive set up's with a raspberry pi running a load of these, ( i have raspberry pi not eruptors !)

Meech

hero member

Activity: 924

Merit: 1000

Power is provided by 2 pci-e connectors from psu. You can also use molex to pci-e adapter. I believe for each cube you would need to run a separate mining proxy. I may be wrong. Shocked

Chris_Sabian

legendary

Activity: 896

Merit: 1001

Quote from: mojacho on April 24, 2014, 10:28:46 AM

have you read below tutorial? Hope its help

https://bitcointalksearch.org/topic/guide-dogies-comprehensive-asicminer-cube-setup-hd-352658

This tutorial is very good.

I have 2 cubes running off a Corsair Gold RM850. The PS has 2 PIC/E power lines. Each cube is attached to one.

mojacho

newbie

Activity: 137

Merit: 0

have you read below tutorial? Hope its help

https://bitcointalksearch.org/topic/guide-dogies-comprehensive-asicminer-cube-setup-hd-352658

sandman102

newbie

Activity: 6

Merit: 0

I am new to mining, just ordered my first cube and I have a Corsair RM1000 PS from another project.

If I want to add a second cube, can I add it to the same PS?

What kind of cable harness do I need t split the supply, and are there harness's available commercially, or do I need to make one?

Thanks

sandman102

Topic: how do I wire 2 block erupter cubes to a single supply (Read 538 times)