http://angryip.org/
Download and run this with and without the miners on .. it will detect any changes
Topic: How to connect 2 Bitmain Antminer S1 machines to mine in one pool w/same network (Read 841 times)
April 11, 2015, 10:10:16 AM
April 10, 2015, 04:17:08 PM
I personally hate DHCP as you never know where the miner is. If done right static is the way I like to go.
I would check and make sure your network is 168.192.1.X - you can use windows and do in cmd window ipconfig. Also for some the default might be 192.168.1.99 or 192.168.0.99.
Do you have a second router you can hook it up to and get it set up on? AT&T Uverse sounds like a pain of a router.
I would check and make sure your network is 168.192.1.X - you can use windows and do in cmd window ipconfig. Also for some the default might be 192.168.1.99 or 192.168.0.99.
Do you have a second router you can hook it up to and get it set up on? AT&T Uverse sounds like a pain of a router.
April 10, 2015, 12:54:45 PM
Hello,
My network will not allow me to connect this second Antminer S1 to begin mining. I was told that I'd have to turn off my old miner and then connect the new miner to my Network and then turn the old S1 one and both would work yet I continue to fail. It there anyone who knows how to do this correctly?
Antminer S1 ...found 192.168.1.XX listed port as friends iPhone
Antminer S3 eventually found 192.168.1.XX via DCHP Client instead of Static Address for IP and it works fine without both Overclocked and Mining normally. This was done because I could not connect and mine BTC via Static IP Address and the Antminer Dealer ( Andre Yates ) whom I bought from.
Note:
04.07.15 - i have a old Antminer S1 running on IP Address 192.168.1.XXX using BTCguild Worker: XXXXXX.btcguild.com:XXXX - XXXXXXXXX_XXXXXXXX - PW = 123 that i have been using.
Note:
04.07.15 - i have my Antminer S3 running on IP Address 192.168.1.XX using BTCGuild Worker: XXXXXX.XXXXXX.XXX:XXXX - XXXXXXXXXX_X - PW = 123
Note: Since 04.01.15 - i have been working to find my IP Address port for a Second Antminer S1 for jdh015232audio on Ebay via my AT&T Uverse Broadband Modem System Device finder IP Address 168.192.1.XXX
So now 04.07.15 I need to connect the new Antminer S1 using BTCguild Worker: XXXXXX.XXXXXX.XXX:XXXX - XXXXXXXXXX_X - PW = 123
Note: When Setting Up an Antminer I had to disconnect to old S1 and turn it off. Then turn on the new S1 and got to Antminer’s S1 website IP 192.168.1.99 and then RESTART the new Antminer S1. Once I did that I added Antminer S1 using BTCguild Worker: XXXXXX.XXXXXX.XXX:XXXX - XXXXXXXXXX_X - PW = 123 . After that I got to SYSTEM and Change the Time to America/ New York Then Save and Apply, Next I clicked on ‘NETWORK’ and under WAN Interface I changed it to DHCP Client instead of it being on Static and press Save and Apply >> this makes the Antminer restart and then I had to find the new IP address. It shoots over to 192.168.1.24 i think but now that’s not it...I’m not into guessing games so i look at my AT&T Uverse IP Address Device finder page to find the new sever server IP address that i just made for the Antminer S1. I and see that my homeboy’s Kay’ iPhone is now at an IP address saying 192.168.1.XXX while his phone was saying 192.168.1.99 when I started this 5 minutes ago.
Once on this is done turn off the New Antminer S1 and turn on the old Antminer S3 I open IP Address 192.168.1.XXX I so I can see how to set 2nd Antmminer S1 to Set to DHCP Client with Hostname antminer MAC - Address 18:C8:E7:81:2E:E9 RX:1.68. MB TX: 579.48.16 KB IPv4 192.168.1.XXX
I've been at this for two going on three weeks now and I can only switch between the two Antminer S1s rather that have them both working w/ my S3. What am I doing wrong or does the Ebay seller wrong in how I should start the process?
My network will not allow me to connect this second Antminer S1 to begin mining. I was told that I'd have to turn off my old miner and then connect the new miner to my Network and then turn the old S1 one and both would work yet I continue to fail. It there anyone who knows how to do this correctly?
Antminer S1 ...found 192.168.1.XX listed port as friends iPhone
Antminer S3 eventually found 192.168.1.XX via DCHP Client instead of Static Address for IP and it works fine without both Overclocked and Mining normally. This was done because I could not connect and mine BTC via Static IP Address and the Antminer Dealer ( Andre Yates ) whom I bought from.
Note:
04.07.15 - i have a old Antminer S1 running on IP Address 192.168.1.XXX using BTCguild Worker: XXXXXX.btcguild.com:XXXX - XXXXXXXXX_XXXXXXXX - PW = 123 that i have been using.
Note:
04.07.15 - i have my Antminer S3 running on IP Address 192.168.1.XX using BTCGuild Worker: XXXXXX.XXXXXX.XXX:XXXX - XXXXXXXXXX_X - PW = 123
Note: Since 04.01.15 - i have been working to find my IP Address port for a Second Antminer S1 for jdh015232audio on Ebay via my AT&T Uverse Broadband Modem System Device finder IP Address 168.192.1.XXX
So now 04.07.15 I need to connect the new Antminer S1 using BTCguild Worker: XXXXXX.XXXXXX.XXX:XXXX - XXXXXXXXXX_X - PW = 123
Note: When Setting Up an Antminer I had to disconnect to old S1 and turn it off. Then turn on the new S1 and got to Antminer’s S1 website IP 192.168.1.99 and then RESTART the new Antminer S1. Once I did that I added Antminer S1 using BTCguild Worker: XXXXXX.XXXXXX.XXX:XXXX - XXXXXXXXXX_X - PW = 123 . After that I got to SYSTEM and Change the Time to America/ New York Then Save and Apply, Next I clicked on ‘NETWORK’ and under WAN Interface I changed it to DHCP Client instead of it being on Static and press Save and Apply >> this makes the Antminer restart and then I had to find the new IP address. It shoots over to 192.168.1.24 i think but now that’s not it...I’m not into guessing games so i look at my AT&T Uverse IP Address Device finder page to find the new sever server IP address that i just made for the Antminer S1. I and see that my homeboy’s Kay’ iPhone is now at an IP address saying 192.168.1.XXX while his phone was saying 192.168.1.99 when I started this 5 minutes ago.
Once on this is done turn off the New Antminer S1 and turn on the old Antminer S3 I open IP Address 192.168.1.XXX I so I can see how to set 2nd Antmminer S1 to Set to DHCP Client with Hostname antminer MAC - Address 18:C8:E7:81:2E:E9 RX:1.68. MB TX: 579.48.16 KB IPv4 192.168.1.XXX
I've been at this for two going on three weeks now and I can only switch between the two Antminer S1s rather that have them both working w/ my S3. What am I doing wrong or does the Ebay seller wrong in how I should start the process?
Jump to: