Author

Topic: I admit it, I'm confused (Read 593 times)

newbie
Activity: 18
Merit: 0
March 05, 2013, 02:26:43 AM
#9
i've had no problems so far

Me neither
newbie
Activity: 5
Merit: 0
March 05, 2013, 01:37:04 AM
#8
i've had no problems so far
newbie
Activity: 7
Merit: 0
March 04, 2013, 11:55:40 PM
#7
I just tried starting qt from the terminal, but the line you gave didn't work. I normally start qt from the execute icon in the download folder (which is where I extracted it to). To be honest I'm a linux noob as well, haha!
legendary
Activity: 3472
Merit: 4801
March 04, 2013, 11:40:22 PM
#6
Just run Bitcoin-Qt from the command line with a space followed by -rescan added to the end of the command.

Code:
bitcoin-qt -rescan

How do you start it up typically?

Or maybe it is --rescan I can't remember
Code:
bitcoin-qt --rescan
newbie
Activity: 7
Merit: 0
March 04, 2013, 11:39:16 PM
#5
I was trying to find out how to do the rescan thing on a linux system, but all I could find was directions for Windows and Mac. Any ideas?
legendary
Activity: 3472
Merit: 4801
March 04, 2013, 11:32:19 PM
#4
I suspect you need to start Bitcoin-Qt up with the -rescan option:

- snip -
It's about this address:
16wJL3gZkrp2QpkszXFaa53twxodpT2kTP

It says it contains 1 BTC at blockchain.info.
- snip -
But according to QT it has 0 btc on it.
Even if I try to dump the private key it says :
- snip -

Fixed. The rescan option did it.
Should have tried it out before posting.
It didn't even took a long time after all.

Thanks.
========================
When I loaded the secure wallet.dat back into the ./bitcoin directory and launched the program, and waited some 18hrs for the blockchain to download (using bitcoin-qt 0.72) , the balance shows as 0! I expect 0.03 that I sent to be there, as seen here: http://blockexplorer.com/address/1KLzQCkiNpjBVJyEJaLSSUzC63xrG9S6MD

What the hell am I doing wrong?
-snip-
- snip -
If so, I'd suggest running Bitcoin-Qt from a command line with the -rescan option added to the command line.

This won't re-download the entire blockchain, so you won't have to wait the 18 hours again, but it will scan the entire blockchain that you have for any missed transactions.
- snip -
Thanks guys!  DannyHamilton's advice did the trick.  I guess this problem must be rare if the -rescan bit isn't in the wiki?  I believe I followed the steps exactly and still.  Glad these forums exist!
newbie
Activity: 7
Merit: 0
March 04, 2013, 11:23:53 PM
#3
Yep, qt is definitely synced. The client is 0.7.2
legendary
Activity: 1288
Merit: 1227
Away on an extended break
March 04, 2013, 11:19:27 PM
#2
Problem is with your bitcoin-qt client. Is it fully synced? Is there a small green tick by the right bottom corner? What is the block count? Which version is your client?

PS: Your coins are safe if it shows up in the blockchain.info, don't worry.
newbie
Activity: 7
Merit: 0
March 04, 2013, 11:15:35 PM
#1
So I thought I had a pretty good grasp on this whole bitcoin thing. But as it turns out, I guess I don't. I made a couple of "offline" wallets with bitcoin-qt on Ubuntu 12.04.1 LTS using usb drives as a virtual OS. So I made 2 wallets, populated 10 received addresses for each wallet, then saved out the wallet.dat files to another usb drive. So I've been using the addresses to get some free coins from the free bitcoin sites. After a couple of weeks I decided to sync these wallets just to see if things were going as I thought they should. Once I load them, and they are synced, neither of the wallets show any transactions. They both have the addresses I had originally made, so it doesn't seem like the wallet.dat files are bad, or that I messed up backing them up. Perhaps I did and just don't know. Anyway, so I looked up the addresses on blockchain.info and found that transactions had been made with the addresses used.

Here are 2 of the addresses if you'd like to check it out yourselves. Any help would be appreciated. Let me know if anymore info is needed. Thanks!

1AdyosNdGHYzkkMEQK9TkwrPs6NexDxfuY

15Fmaudd57QmZQgCX4o1AVmBFo5HYhir78
Jump to: