I may also buy it from you, I can use it with my erupter. You can send me a pm.
you can also try to replace the block erupter with a new one.
Topic: Just got a ASICMiner Tube 800+ GHs but it won't start mining, sitting idle (Read 7094 times)
March 28, 2015, 03:05:37 PM
March 28, 2015, 03:00:13 PM
It may be a software issue. I had problems with the controller as well.
But not 2 minutes, mining was stopping at random times...
The last chance I tried was to use a proxy from Slush's pool. I downloaded the proxy to a pc which is running 7/24
and pointed the erupter to use proxy's IP
After that everthing worked fine...
You may have a power adapter problem which should be 12V 1Amp. Check it out.
That's all I know.
But not 2 minutes, mining was stopping at random times...
The last chance I tried was to use a proxy from Slush's pool. I downloaded the proxy to a pc which is running 7/24
and pointed the erupter to use proxy's IP
After that everthing worked fine...
You may have a power adapter problem which should be 12V 1Amp. Check it out.
That's all I know.
March 21, 2015, 03:47:51 AM
I had ASICMiner Tube 800+ GHs for the last 3 month, now the controller's rebooting every 2Min.
the controller's is working OK when not connecting to the miner, but the moment I connecting it to the miner its start rebooting every 2 Min.
Any idea?
Please HELP!
the controller's is working OK when not connecting to the miner, but the moment I connecting it to the miner its start rebooting every 2 Min.
Any idea?
Please HELP!
November 25, 2014, 08:47:21 PM
It was a PSU ISSUE, It took me this long to convince wifey to buy a Zalman 1250PSU and its chugging away with the settings given to me by philip !!!!!!
Now I've tried my settings from slushies pool and nadda........even tho I use them on other miners,,,,,,,,,
Who can reccd a good pool with easy setup
Now I've tried my settings from slushies pool and nadda........even tho I use them on other miners,,,,,,,,,
Who can reccd a good pool with easy setup
October 08, 2014, 08:52:24 PM
I copied these settings from another user who posted, my settings don't mine either, even tho they work on other miners......
October 08, 2014, 10:05:27 AM
Does ghash allow the password to be d=1024? I always set the difficulty on the worker page. Everything else on the page looks like my tube, so it may be a PSU issue.
October 08, 2014, 08:13:13 AM
I've lower to below stock settings here is a screen shot : https://www.dropbox.com/s/igf3dr81ok981dd/settings.jpg?dl=0
Can anyone spot anything wrong , its still not mining
Can anyone spot anything wrong , its still not mining
October 05, 2014, 10:07:54 AM
Pull the comm cable from the last daisy chained board and try again.
If it holds I'd suggest your PS is not suitable to carry the load of 4 boards.
If it holds I'd suggest your PS is not suitable to carry the load of 4 boards.
what is the op's psu?
change the setting for freq from 290 to 250 if it runs and stays running it means your psu can not handle the power load.
freq 250 will use less power then freq 290
250 is underclocked
270 is stock
290 is overclock
this may be an underpowered psu. I think you may get it running at 250 freq.
October 03, 2014, 06:30:53 PM
Pull the comm cable from the last daisy chained board and try again.
If it holds I'd suggest your PS is not suitable to carry the load of 4 boards.
If it holds I'd suggest your PS is not suitable to carry the load of 4 boards.
October 03, 2014, 08:48:13 AM
I've input your settings, now it boots up and then after about 20secs both it and my 1000watt power supply turn off................... not blaming the settings just reporting......... its on its own circuit so i know its not a power source issue, *bangs head on desk
October 03, 2014, 05:07:05 AM
copy my mining pool see if you get numbers to show it is mining . you need to have all the dip switches done correctly. a good pool entry and correct ip's.
my router is 192.168.0.1 so i can use that for my gateway setting.
if you have a router like mine then make sure you can match it up correctly
I had 2
my router is 192.168.0.1 so i can use that for my gateway setting.
if you have a router like mine then make sure you can match it up correctly
I had 2
October 02, 2014, 09:37:45 PM
and yes I'm connected to UART1
October 02, 2014, 08:31:27 PM
yes I see the boards when I press test they all show 0.00 , I only had one connector coming from it to attach the ethernet controller............ the rest were already hooked daisy chained together........
THANKS so much for your ideas, I'll even pay some btc to get this running.
THANKS so much for your ideas, I'll even pay some btc to get this running.
October 02, 2014, 07:12:03 PM
are you in slot 1 of the controller? also when you hit the test button do you see the boards?
October 01, 2014, 05:23:03 PM
So I got a ASICMiner Tube 800+ GHs from http://www.112bit.com/product/asicminer-tube-800-ghs-sha256-bitcoin-miner-kit/
Had to source my own power adapter for the Ethernet Controller .....no bigs but was "fun"
Now.....I've accessed it thru Chrome and input all my setting and username etc, BUT it does not start mining, just sitting there at 0.00gh
Any ideas? What info should I give you guys to help out ?
Ian
Had to source my own power adapter for the Ethernet Controller .....no bigs but was "fun"
Now.....I've accessed it thru Chrome and input all my setting and username etc, BUT it does not start mining, just sitting there at 0.00gh
Any ideas? What info should I give you guys to help out ?
Ian
Jump to: