Topic: MSI 5850 (ref) Volterra problem (Read 1683 times)
legendary
Activity: 1862
Merit: 1011
Reverse engineer from time to time
My 5850 is pretty much the same. High VRM temps, high AMPs whereas the 5870 is waaay below these temps/amps.
68 amps draw for 0.875v and 400mhz core is an EXTREME amount... my 5970 cores only draw 53 amps with 1v and 755 core.
Good point, so maybe the problem is N.2 i.e. VRM 1 is shorted or faulty, maybe I'll try to isolate it and see what happens. Does anybody know how to do that, to cut power supply to that VT1157SF
Edit: after some more serching I found almost the same story:
Quote
Hello
I have problem with my Radeon 5970. On the master GPU have VDDC Phase #2 Temperature very high, but all other temp. is good. When load GPU to 99% temp. rise more 120 and crash my system. VDDC Current is ~ 80A load and ~12A idle. On the slave GPU all is good. VDDC Current is ~ 54A load, and temp. is good. I change one VT1157SF from PCB (U72) but this not fix my problem. When I remove (U72) card work, but available only one GPU (slave), and not crash when load 99%. Anyone known where is located sensor "VDDS Phase #2" for master GPU? Maybe Master GPU is broken? I need fix my card but can't locate where is the problem. If anyone have information which parts more I need check please help.
Regards
Sakura
I have problem with my Radeon 5970. On the master GPU have VDDC Phase #2 Temperature very high, but all other temp. is good. When load GPU to 99% temp. rise more 120 and crash my system. VDDC Current is ~ 80A load and ~12A idle. On the slave GPU all is good. VDDC Current is ~ 54A load, and temp. is good. I change one VT1157SF from PCB (U72) but this not fix my problem. When I remove (U72) card work, but available only one GPU (slave), and not crash when load 99%. Anyone known where is located sensor "VDDS Phase #2" for master GPU? Maybe Master GPU is broken? I need fix my card but can't locate where is the problem. If anyone have information which parts more I need check please help.
Regards
Sakura
68 amps draw for 0.875v and 400mhz core is an EXTREME amount... my 5970 cores only draw 53 amps with 1v and 755 core.
Hi,
I bought this card as faulty several months ago, First run - it starts, but there was a very strange noise from the mobo's speaker. Then I noticed that one of the voltera's Capacitors was blown away (see pic1). I had to do a bridge for re soldering the new Capacitor as the pcb path was missing anyway this was done and now the card works without the creepy speaker noise from the mobo. The problem is that when you load the card VRM 1 starts overheating to extreme while VRM 2 and 3 stays cold, but eventuaaly gets heated by the PCB and cooling plate. At stock freq/voltage VRM gets above 140C in no time and card shutdown itself. I managed to get it to stable values for mining at the lowest 0.875 V and 430Mhz (177MH/s
) the VRM stays around 109C and that way the card is stable and mining for more than 4 months without a glitch. It can go higher freq, but the VRM gets too hot, more than ~120C
IMO there are two possible scenarios here
1. VRM 2 and 3 are not working at all and the power is driven by VRM 1 which can't handle the full power requirements of the chip.
2. VRM 1 is shorted or just faulty and thats why it overheats.
What is your oppinion, now that the GPU mining is going to end I have more time to experiment with this.
Not actual pictures
Edit: I remember now that same Capacitor (pic1) was desoldered for VRM 3 too.
P.S.
===
This is not a cooling problem
I bought this card as faulty several months ago, First run - it starts, but there was a very strange noise from the mobo's speaker. Then I noticed that one of the voltera's Capacitors was blown away (see pic1). I had to do a bridge for re soldering the new Capacitor as the pcb path was missing anyway this was done and now the card works without the creepy speaker noise from the mobo. The problem is that when you load the card VRM 1 starts overheating to extreme while VRM 2 and 3 stays cold, but eventuaaly gets heated by the PCB and cooling plate. At stock freq/voltage VRM gets above 140C in no time and card shutdown itself. I managed to get it to stable values for mining at the lowest 0.875 V and 430Mhz (177MH/s
) the VRM stays around 109C and that way the card is stable and mining for more than 4 months without a glitch. It can go higher freq, but the VRM gets too hot, more than ~120CQuote
Device [1]: Cypress [Radeon HD 5800 Series]
Current core voltage: 0.8750 V
Presets: 0.8750 / 0.8750 / 0.8750 / 0.8750 V
Core power draw: 68.81 A (60.21 W)
VRM temperatures: 109 / 58 / 50 C
Current core voltage: 0.8750 V
Presets: 0.8750 / 0.8750 / 0.8750 / 0.8750 V
Core power draw: 68.81 A (60.21 W)
VRM temperatures: 109 / 58 / 50 C
IMO there are two possible scenarios here
1. VRM 2 and 3 are not working at all and the power is driven by VRM 1 which can't handle the full power requirements of the chip.
2. VRM 1 is shorted or just faulty and thats why it overheats.
What is your oppinion, now that the GPU mining is going to end I have more time to experiment with this.
Not actual pictures
Edit: I remember now that same Capacitor (pic1) was desoldered for VRM 3 too.
P.S.
===
This is not a cooling problem
Jump to: