You will be very lucky if you get that rock solid at that mem clock. But it has been known to happen on here.
I wish so. 
I will post my updates (by checking on ethminer) once I check the same 
Topic: My Ethereum mining stats suck- what am I doing wrong? (Read 401 times)
I will post my updates (by checking on ethminer) once I check the same
You will be very lucky if you get that rock solid at that mem clock. But it has been known to happen on here.
Okay, so I have swapped the wireless with LAN and it looks much stable for the last half an hour.
Also I have modified my OC as below
Driver: 372.54
Power : 65%
Core : -200
Mem: +1000
fan speed : auto
Miner used : Claymore v9.7 - with Eth only Mining on ethermine.
Now my 2 GTX 1060 GPUs run at 50 MH/s which I believe are amazing results. Haven't thought of taking remote fearing it would crash.
Need to test on GTX 1060 optimized ethminer. I believe it would run better
-pr0ximus
Also I have modified my OC as below
Driver: 372.54
Power : 65%
Core : -200
Mem: +1000
fan speed : auto
Miner used : Claymore v9.7 - with Eth only Mining on ethermine.
Now my 2 GTX 1060 GPUs run at 50 MH/s which I believe are amazing results. Haven't thought of taking remote fearing it would crash.
Need to test on GTX 1060 optimized ethminer. I believe it would run better
-pr0ximus
Run the cards at stock speeds for a while, it might well be that overclock.
Hello All,
Good day.
I am new to the forum (so please be gentle to me).Not sure if this is the right place to ask but I have successfully setup my 2 GPUs for Ethereum Mining and running for few days now. My stats doesn't seem promising.
Below are the details that could help you help me.
GPU : 2x Zotac GTX 1060 6Gb Amp! Edition
Driver version: 384.76
Mining pool tested: Nanopool (will share the stats below) and F2Pool (lot of rejections)
Mining software : Claymore dual mining v9.6
OC settings : Power : 60%, Core +100, mem +900 (4704mhz), fan auto.
Connected to wireless internet.
hash rate : 46+mh/s
Initially it was running without any troubles but now I couldn't figure out what makes it look like below: Nanopool stats.
As you could see, it constantly runs at 46+mh/s from GPU while the accepted shares are not even half of it.
Even with f2pool, i get a lot of rejections.
I searched all over the internet and couldn't find a solution. I felt this is the right place to seek help. (I've been a silent observer these days). Could someone let me know how i could increase the success rate or where am I doing wrong (if any)..
Thanks in advance
-pr0ximus
Good day.
I am new to the forum (so please be gentle to me
).Not sure if this is the right place to ask but I have successfully setup my 2 GPUs for Ethereum Mining and running for few days now. My stats doesn't seem promising. Below are the details that could help you help me.
GPU : 2x Zotac GTX 1060 6Gb Amp! Edition
Driver version: 384.76
Mining pool tested: Nanopool (will share the stats below) and F2Pool (lot of rejections)
Mining software : Claymore dual mining v9.6
OC settings : Power : 60%, Core +100, mem +900 (4704mhz), fan auto.
Connected to wireless internet.
hash rate : 46+mh/s
Initially it was running without any troubles but now I couldn't figure out what makes it look like below: Nanopool stats.
As you could see, it constantly runs at 46+mh/s from GPU while the accepted shares are not even half of it.
Even with f2pool, i get a lot of rejections.
I searched all over the internet and couldn't find a solution. I felt this is the right place to seek help. (I've been a silent observer these days). Could someone let me know how i could increase the success rate or where am I doing wrong (if any)..
Thanks in advance
-pr0ximus
Jump to: