My S19 not working | Bitcointalksearch.org

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

Quote from: skytheflash on November 27, 2023, 08:36:52 PM

My S19 has an Amlogic control board and the only choice was to use OTG USB to flash.
No SD card slot.

Have you tried to reflash it again as I suggested in my previous post?
If this issue just came up after you flashed I have a strong feeling this is just a software issue that is why I suggested you try to flash it again but this time use the stock firmware from Bitmain.

If still does not work there's also a TTL method to try but it needs a TTL cable to connect to the control board(RX, TX, and GND).
Check my old post here below.
- https://bitcointalksearch.org/topic/m.62771173

skytheflash

newbie

Activity: 3

Merit: 0

My S19 has an Amlogic control board and the only choice was to use OTG USB to flash.
No SD card slot.

philipma1957

legendary

Activity: 4326

Merit: 8950

'The right to privacy matters'

Quote from: skytheflash on November 27, 2023, 08:27:10 PM

sorry for the confusion,

I have installed it already and it's been 2 months.

Recently, today I realised that no indicator is flashing and the machine is stuck at full fan speed when started and does not even provide IP address.

so did you simply use an sd card or did you foolishly flash the controller.

If you flashed the controller it will be harder to fix.

If you did an sd card just remove the sd card.

skytheflash

newbie

Activity: 3

Merit: 0

sorry for the confusion,

I have installed it already and it's been 2 months.

Recently, today I realised that no indicator is flashing and the machine is stuck at full fan speed when started and does not even provide IP address.

BitMaxz

legendary

Activity: 3472

Merit: 3217

Playbet.io - Crypto Casino and Sportsbook

Do you mean it does not show any light indicator during flashing vnish firmware?
If I'm right the firmware you downloaded might be corrupted or the OTG is faulty.
To fix this redownload the firmware make sure you don't use any download manager like IDM or try to replace the OTG/SD card you use.

If not, try to flash it again through OTG but this time use the stock firmware, and let's see if it would fix the light indicator issue.

skytheflash

newbie

Activity: 3

Merit: 0

Hello,

I have Antminer S19, It has Vanish Firmware installed, and I just realised that after turning it on, it does not show any indicator. (Red and Green)
Fans are fully working but stuck at full speed.

Waited long enough already but still no indicator.

I read about indicators on Bitmain website, per them if both indicators are not showing even once, then the control board is damaged or I need to change firmware/factory reset.

Not sure how to proceed with a factory reset or if need to flash Vanish again!

(If need to install Vanish again, I need the green indicator to understand when to remove and plug USB OTG in the process, hence also the confusion Sad

)

Sources:
(https://support.bitmain.com/hc/en-us/articles/360018826774-What-do-miner-s-signal-lights-mean-)

Fault 4:
The control board is faulty, use the SD card to upgrade the control board or replace the control board.

Indicator light judgment during server operation
Fault light(red)     extinguish   flashing   long light   extinguish   extinguish   flashing
Normal light(green)   flashing   extinguish   long light   long light   extinguish   flashing
Working conditions   normal   fault 1   fault 2   fault 3   fault 4   fault 5

Help me, Thank you

Topic: My S19 not working (Read 99 times)