Nanofury NF1 not working on Raspbian

Wongi

newbie

Activity: 49

Merit: 0

Mineforeman made an update to Minepeon 0.2.4.3
Now Nanofury is supported without hidapi.

http://minepeon.com/forums/viewtopic.php?f=4&t=666&start=50

http://minepeon.com/index.php/Cgminer-HEXu

Still need the USB1 workaround:
sudo nano /boot/cmdline.txt
then add dwc_otg.speed=1 at the end of line

It's working like a charm in Minepeon now

http://s7.directupload.net/images/140108/temp/lxhkbgra.jpg

http://s1.directupload.net/images/140108/temp/bfi72ctj.jpg

Taint

member

Activity: 60

Merit: 10

There's a patch for cgminer listed in the main 'Nanofury Project - Open Source Design' Topic.

Tested on a linux miner, I haven't tested it under raspian.

I'm seeing considerably higher performance and no more 'Frequency Drop' messages.

snoopy_nzl

member

Activity: 67

Merit: 10

Quote from: derjanb on December 05, 2013, 03:10:27 PM

Working fine here after hours of trying... Grin

At least I get ~2.3 GH/s out of the Nanofury.

I'm using bfgminer 3.8.0 (latest git version) and all you have to do (after compiling) is to enforce the USB 2.0 low speed mode to make the USB communication stable. Note: this will also limit the network speed of your Raspi!

The slowdown can be achieved by putting dwc_otg.speed=1 into /boot/cmdline.txt. Note: all statements need to be at one line.

See this page for more infomation: http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=53832#sig411106 (the last section at the bottom.

Question: what does

Quote

NFY 0: Frequency drop over 50% detected, reinitialising

mean? I see a lot of these messages.

is it possible to slowdown on windows as well? I see the same frequency issue id love to fix.

infinitecoin1993

member

Activity: 107

Merit: 10

Got the miners working in putty,

But how i make it working from the web interface? Because its showing no devices.

Wongi

newbie

Activity: 49

Merit: 0

For me bfg miner 3.6.0 is working.

http://s1.directupload.net/images/131221/q535fouy.jpg

hammer

newbie

Activity: 18

Merit: 0

Same by me. Many Reinitialising Huh

Have a man a solution for this?

achib

newbie

Activity: 51

Merit: 0

This looks great .. at least it works now !
But look at this:

--------------------------------------------------------------------------------
NFY 0: | 2.18/ 2.09/ 1.89Gh/s | A:11 R:0+0(none) HW: 5/4.5%
BPM 0: | 2.37/ 2.36/ 2.07Gh/s | A: 7 R:0+0(none) HW:51/ 30%
--------------------------------------------------------------------------------
[2013-12-12 18:53:47] NFY 0: Frequency drop over 50% detected, reinitialising
[2013-12-12 18:53:53] Accepted 07cf16ff NFY 0 Diff 32/16
[2013-12-12 18:53:57] NFY 0: Frequency drop over 50% detected, reinitialising
[2013-12-12 18:54:05] NFY 0: Frequency drop over 50% detected, reinitialising
[2013-12-12 18:54:13] Accepted 04ae5508 BPM 0 Diff 54/16
[2013-12-12 18:54:19] NFY 0: Frequency drop over 50% detected, reinitialising
[2013-12-12 18:54:20] Stratum from pool 0 requested work update
[2013-12-12 18:54:25] Accepted 0e87703f NFY 0 Diff 17/16
[2013-12-12 18:54:29] Accepted 04844e77 NFY 0 Diff 56/16
[2013-12-12 18:54:37] NFY 0: Frequency drop over 50% detected, reinitialising
[2013-12-12 18:54:42] Accepted 0624290d NFY 0 Diff 41/16
[2013-12-12 18:54:44] NFY 0: Frequency drop over 50% detected, reinitialising
[2013-12-12 18:54:44] Accepted 0a8e4540 BPM 0 Diff 24/16
[2013-12-12 18:54:52] NFY 0: Frequency drop over 50% detected, reinitialising

Any idea how to get them work correct ? If i plug them to my windows machine it works without any errors Sad

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: Haribo1980 on December 11, 2013, 12:29:14 PM

yeeeeehaaaw.... IT WORKS !!!! You're my daily HERO Zich !!!!!! Grin

Thanks a lot... !!!!

No problem dude, but i can't take all credit Wink

. All credit go to derjanb who discover the usb speed problem Grin

Haribo1980

newbie

Activity: 3

Merit: 0

yeeeeehaaaw.... IT WORKS !!!! You're my daily HERO Zich !!!!!! Grin

Thanks a lot... !!!!

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: Haribo1980 on December 10, 2013, 10:50:25 AM

Hello,

could anyone sent me a kind of tutorial how to get the nanofury working on rasberry pi? I dont know much about linux.

Raspian ist still installed, and networkspeed ist reduced like in your messages. But which bfgminer version should I install (link?). What do you mean with "after comiling"

are there any other settings do do? ... I tryed lots of versions but nothing works... A small tutorial would save my next 5 evenings Cheesy

Greetings from Germany

First you need to install needed library

Code:

1. sudo aptitude update
2. sudo aptitude install libudev-dev libusb-1.0-0-dev libfox-1.6-dev autotools-dev autoconf automake libtool libncurses-dev yasm curl libcurl4-openssl-dev libjansson-dev pkg-config uthash-dev make pkg-config yasm

Second download HIDAPI from git

Code:

1. git clone git://github.com/signal11/hidapi.git hidapi
2. cd hidapi
3. ./bootstrap
4. ./configure --prefix=/usr
5. make
6. sudo make install

Third download bfgminer to some directory(in this example is "miner")

Code:

1. mkdir miner
2. cd miner
3. wget http://luke.dashjr.org/programs/bitcoin/files/bfgminer/3.8.1/bfgminer-3.8.1.tbz2
4. tar xvf bfgminer-3.8.1.tbz2
5. cd bfgminer-3.8.1
6. ./configure 
7. make

You can enable or disable some miner while run ./configure bfgminer with this options
Example: ./configure --enable-bfsb --disable-bitforce

Code:

	--disable-avalon        Compile support for Avalon (default enabled)
	--enable-cpumining      Build with cpu mining support(default disabled)
	--enable-opencl         Compile support for OpenCL (default disabled)
	--disable-adl           Build without ADL monitoring (default enabled)
	--disable-bitfury       Compile support for Bitfury (default enabled)
	--enable-bfsb           Compile support for BFSB (default disabled)
	--disable-bigpic        Compile support for Big Picture Mining USB (default enabled)
	--disable-littlefury    Compile support for LittleFury (default enabled)
	--disable-nanofury      Compile support for NanoFury (default enabled)
	--disable-hashbuster    Compile support for HashBuster Nano (default enabled)
	--disable-hashbuster2   Compile support for HashBuster Micro (default if libusb)
	--enable-metabank       Compile support for Metabank (default disabled)
	--disable-bitforce      Compile support for BitForce (default enabled)
	--disable-icarus        Compile support for Icarus (default enabled)
	--disable-klondike      Compile support for Klondike (default enabled)
	--enable-knc            Compile support for KnC (default disabled)
	--disable-modminer      Compile support for ModMiner (default enabled)
	--disable-x6500         Compile support for X6500 (default enabled)
	--disable-ztex          Compile support for ZTEX (default if libusb)
	--enable-scrypt         Compile support for scrypt mining (default disabled)
	--with-system-libblkmaker  Use system libblkmaker rather than bundled one (default disabled)
	--without-sensors       Build with libsensors monitoring (default enabled)
	--without-curses        Compile support for curses TUI (default enabled)
	--without-libmicrohttpd Compile support for libmicrohttpd getwork server (default enabled)
	--without-libevent      Compile support for libevent stratum server (default enabled)
	--without-libusb        Compile using libusb (default enabled)
	--without-libudev       Autodetect FPGAs using libudev (default enabled)

Then change usb speed to usb 1 with text editor nano

Code:

1. sudo nano /boot/cmdline.txt
then add dwc_otg.speed=1 at the end of line

To run bfgminer just go to the directory

Code:

1. cd miner
2. cd bfgminer-3.8.1
3. sudo ./bfgminer

That was the summary i colected from other thread since i am also linux noob Grin

Haribo1980

newbie

Activity: 3

Merit: 0

Hello,

could anyone sent me a kind of tutorial how to get the nanofury working on rasberry pi? I dont know much about linux.

Raspian ist still installed, and networkspeed ist reduced like in your messages. But which bfgminer version should I install (link?). What do you mean with "after comiling"

are there any other settings do do? ... I tryed lots of versions but nothing works... A small tutorial would save my next 5 evenings Cheesy

Greetings from Germany

thedue

hero member

Activity: 662

Merit: 500

NFY 0: Frequency drop over 50% detected, reinitialising

---

I´m getting those too with my NF1... any idea of what this should tell us?!

Zich

legendary

Activity: 1190

Merit: 1000

Quote from: derjanb on December 05, 2013, 03:10:27 PM

Working fine here after hours of trying... Grin

At least I get ~2.3 GH/s out of the Nanofury.

I'm using bfgminer 3.8.0 (latest git version) and all you have to do (after compiling) is to enforce the USB 2.0 low speed mode to make the USB communication stable. Note: this will also limit the network speed of your Raspi!

The slowdown can be achieved by putting dwc_otg.speed=1 into /boot/cmdline.txt. Note: all statements need to be at one line.

See this page for more infomation: http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=53832#sig411106 (the last section at the bottom.

Question: what does

Quote

NFY 0: Frequency drop over 50% detected, reinitialising

mean? I see a lot of these messages.

Thanks a lot derjanb. It work Grin

RicRock

sr. member

Activity: 290

Merit: 250

Quote from: derjanb on December 05, 2013, 03:10:27 PM

Working fine here after hours of trying... Grin

At least I get ~2.3 GH/s out of the Nanofury.

I'm using bfgminer 3.8.0 (latest git version) and all you have to do (after compiling) is to enforce the USB 2.0 low speed mode to make the USB communication stable. Note: this will also limit the network speed of your Raspi!

The slowdown can be achieved by putting dwc_otg.speed=1 into /boot/cmdline.txt. Note: all statements need to be at one line.

See this page for more infomation: http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=53832#sig411106 (the last section at the bottom.

Question: what does

Quote

NFY 0: Frequency drop over 50% detected, reinitialising

mean? I see a lot of these messages.

Good job! never occurred to me to try setting low speed mode.

Unfortunately, I sold mine off so can't test it out

derjanb

newbie

Activity: 24

Merit: 0

Working fine here after hours of trying... Grin

At least I get ~2.3 GH/s out of the Nanofury.

I'm using bfgminer 3.8.0 (latest git version) and all you have to do (after compiling) is to enforce the USB 2.0 low speed mode to make the USB communication stable. Note: this will also limit the network speed of your Raspi!

The slowdown can be achieved by putting dwc_otg.speed=1 into /boot/cmdline.txt. Note: all statements need to be at one line.

See this page for more infomation: http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=53832#sig411106 (the last section at the bottom.

Question: what does

Quote

NFY 0: Frequency drop over 50% detected, reinitialising

mean? I see a lot of these messages.

RicRock

sr. member

Activity: 290

Merit: 250

Quote from: Aggrophobia on November 07, 2013, 03:37:06 PM

Quote from: RicRock on November 07, 2013, 11:56:27 AM

Same problem.

detecting them but not assigning a device (i.e. /dev/ttyUSB0 for erupters, /dev/ttyACM0 for blue fury)

What device should they appear as?

/dev/ttyNFY0

do you really see that device in the /dev directory?

I'm thinking it's /dev/hidraw0 but I'm unclear.

Anyone else having luck?

Edit:

If it is hidraw* they are created upon boot with owners root:root instead of root:dialout and 600 permissions with no T sticky bit set.

Even manually changing those things makes no difference to bfgminer

neoneos

newbie

Activity: 6

Merit: 0

I noticed that when I connect Nanofury to Raspberry running Minepeon I see Microchip Technology Inc. in a list by lsusb command. So I think Nanofury is detected, but it is not working. How do I specify options to make it work?

Aggrophobia

legendary

Activity: 1106

Merit: 1001

Quote from: RicRock on November 07, 2013, 11:56:27 AM

Same problem.

detecting them but not assigning a device (i.e. /dev/ttyUSB0 for erupters, /dev/ttyACM0 for blue fury)

What device should they appear as?

/dev/ttyNFY0

RicRock

sr. member

Activity: 290

Merit: 250

Same problem.

detecting them but not assigning a device (i.e. /dev/ttyUSB0 for erupters, /dev/ttyACM0 for blue fury)

What device should they appear as?

neoneos

newbie

Activity: 6

Merit: 0

I now installed Minepeon and still Nanofury doesn't work.

neoneos

newbie

Activity: 6

Merit: 0

Same. Not working.

Beastlymac

hero member

Activity: 630

Merit: 501

Miner Setup And Reviews. WASP Rep.

Update to bfgminer 3.5.1

neoneos

newbie

Activity: 6

Merit: 0

Not working. Raspbian still doesn't see Nanofury. The LED on Nanofury is not on. When I connect it to Windows, it comes on after bfgminer starts.

viriat0

hero member

Activity: 1008

Merit: 501

Try this:

bfgminer.exe -o stratum+tcp://pool -u user -p password -G -S all --set-device NFY:osc6_bits=52

neoneos

newbie

Activity: 6

Merit: 0

Hello.

I can't get Nanofury NF1 to work on Raspbian. I have been successfully using Block Erupters and Nanofury works excellent on Windows. I am using -S auto on Windows and -S all command on Raspbian, and it does detect Erupters, but not Nanofury. I am using bfgminer 3.4.0. Waiting for your advice.

Thanks.

Topic: Nanofury NF1 not working on Raspbian (Read 6554 times)