Thanks you so much for help guys, appreciate.
Indeed I found the solution, it was the temperature protection which was switching off the hash rate.
Topic: need help with new S9 (Read 189 times)
Hi fanatic 26
Thank you so much for help.
Indeed it works after I waited longer. I got a hardware version and BMiner version on the overview appearing and then some numbers on the miner status.
Unfortunately it seems like I'm facing some other troubles.
The GH/S(RT) goes up to 14.000 for a few seconds then goes to 0.00 on three cards. Then the red fault light on the miner goes on. I tried on reset again once and every time waited around an hour.
Any idea of the problem?
thanks
Thank you so much for help.
Indeed it works after I waited longer. I got a hardware version and BMiner version on the overview appearing and then some numbers on the miner status.
Unfortunately it seems like I'm facing some other troubles.
The GH/S(RT) goes up to 14.000 for a few seconds then goes to 0.00 on three cards. Then the red fault light on the miner goes on. I tried on reset again once and every time waited around an hour.
Any idea of the problem?
thanks
I was get the same problem. the fans or the socket is missing. Or the high and low temperature is taking protection.
Try resetting the machine. from panel: System>upgrage>perform reset
It sounds like a psu problem. Are you running an APW3 on 120V? it won't work, you would need two APW3's to run on 120V
Hi fanatic 26
Thank you so much for help.
Indeed it works after I waited longer. I got a hardware version and BMiner version on the overview appearing and then some numbers on the miner status.
Unfortunately it seems like I'm facing some other troubles.
The GH/S(RT) goes up to 14.000 for a few seconds then goes to 0.00 on three cards. Then the red fault light on the miner goes on. I tried on reset again once and every time waited around an hour.
Any idea of the problem?
thanks
Thank you so much for help.
Indeed it works after I waited longer. I got a hardware version and BMiner version on the overview appearing and then some numbers on the miner status.
Unfortunately it seems like I'm facing some other troubles.
The GH/S(RT) goes up to 14.000 for a few seconds then goes to 0.00 on three cards. Then the red fault light on the miner goes on. I tried on reset again once and every time waited around an hour.
Any idea of the problem?
thanks
The Socket connect failed: connection refused, the missing bmminer version, and hardware version are all connected to bmminer. If it is not running and hashing these errors are all completely normal and not indicative of a problem. Upon first boot, the s9 can take over an hour to run its tests and checks. You just need to be patient and let the miner run for a while.
If it still doesnt connect after letting it run for a few hours then it is time to take a look at the kernel log to see if there are actual errors.
If it still doesnt connect after letting it run for a few hours then it is time to take a look at the kernel log to see if there are actual errors.
Hello everyone, 
I'm new in mining, I just got a new S9 two days ago from bitmain.
Unfortunately I cannot make the S9 working. I still got the message "Socket connect failed: Connection refused" on the system overview page. I also have nothing on BMIner version champ ( i guess it's normal if he cannot connect)
First I didn't have anything on the hardware version line, so I tried to upgrade the firmware, I also upgrade with the fix and then upgrade again. since then I have Socket connect failed: Connection refused
I tried with another network cable
I have a new APW3 psu from bitmain i don't think it would be the problem.
I tried a reset and also reboot.
I also tried like bit main suggests on their website to disconnect the mother board from the cards but the message socket connect failed was still there, so I don't think that one card could be faulty.
Anybody has any clue that could help me?
I wrote to bitmain, but I guess they need a few days to answer
Any suggestion would be welcome as I start to loose hope in mining.
Thanks
I'm new in mining, I just got a new S9 two days ago from bitmain.
Unfortunately I cannot make the S9 working. I still got the message "Socket connect failed: Connection refused" on the system overview page. I also have nothing on BMIner version champ ( i guess it's normal if he cannot connect)
First I didn't have anything on the hardware version line, so I tried to upgrade the firmware, I also upgrade with the fix and then upgrade again. since then I have Socket connect failed: Connection refused
I tried with another network cable
I have a new APW3 psu from bitmain i don't think it would be the problem.
I tried a reset and also reboot.
I also tried like bit main suggests on their website to disconnect the mother board from the cards but the message socket connect failed was still there, so I don't think that one card could be faulty.
Anybody has any clue that could help me?
I wrote to bitmain, but I guess they need a few days to answer
Any suggestion would be welcome as I start to loose hope in mining.
Thanks
Jump to: