It seems according to your logs it is a front0 fan that doesn't have RPM
So there's a slight difference from the result you edited above.
fan_id = 0 = Front0 = top front
fan_id = 1 = Front1 = bottom front
If I'm wrong, you can also try to check the right location of the fan under the miners status, or a better way is to remove the fans one by one and then look for the logs to see if there's a change on the RPM to all fans so that you know which fan exactly is the broken one.
Topic: New S19k Pro Stopped Working after 1 week (Read 51 times)
It's surprisingly difficult to figure out what fan is what and there is a serious lack of information about it.
According to Bitmain
J12 = fan_id = 3
J13 = fan_id = 2
J15 = fan_id = 0
J14 = fan_id = 1
But I have J11, J12, J13, J14, and according to the labels on the control board
J11 = Fan 1
J12 = Fan 3
J13 = Fan 2
J14 = Fan 4
So do I assume Fan 2 = fan_id = 1 = J13 = Rear0 = bottom back?
UPDATE: trail & error results:
J11 = fan_id = 1 = Fan 1 = Front0 = bottom front
J12 = fan_id = 0 = Fan 3 = Front1 = top front
J13 = fan_id = 3 = Fan 2 = Rear0 = bottom back
J14 = fan_id = 2 = Fan 4 = Rear1 = top back
According to Bitmain
J12 = fan_id = 3
J13 = fan_id = 2
J15 = fan_id = 0
J14 = fan_id = 1
But I have J11, J12, J13, J14, and according to the labels on the control board
J11 = Fan 1
J12 = Fan 3
J13 = Fan 2
J14 = Fan 4
So do I assume Fan 2 = fan_id = 1 = J13 = Rear0 = bottom back?
UPDATE: trail & error results:
J11 = fan_id = 1 = Fan 1 = Front0 = bottom front
J12 = fan_id = 0 = Fan 3 = Front1 = top front
J13 = fan_id = 3 = Fan 2 = Rear0 = bottom back
J14 = fan_id = 2 = Fan 4 = Rear1 = top back
you lost a fan it happens. buy a fan and replace it.
https://altairtech.io/product/antminer-120mm-replacement-fan-for-s19-s17-s11-s15-and-s9-series/
make sure you get a square pin if the bad fan has a square pin
make sure you get a rectangle pin if the bad fan has a rectangular pin.
https://altairtech.io/product/antminer-120mm-replacement-fan-for-s19-s17-s11-s15-and-s9-series/
make sure you get a square pin if the bad fan has a square pin
make sure you get a rectangle pin if the bad fan has a rectangular pin.
Hmm, maybe just getting the fan is less trouble than trying to work with the vendor I purchased from.
I wonder... I have a ton of spare fans from L3's and S9's. Will they work here?
maybe the s9 fan is fast enough.
if it tops out at 4500 rpm it will likely not work but if it goes to 500 or more it should be good
you lost a fan it happens. buy a fan and replace it.
https://altairtech.io/product/antminer-120mm-replacement-fan-for-s19-s17-s11-s15-and-s9-series/
make sure you get a square pin if the bad fan has a square pin
make sure you get a rectangle pin if the bad fan has a rectangular pin.
https://altairtech.io/product/antminer-120mm-replacement-fan-for-s19-s17-s11-s15-and-s9-series/
make sure you get a square pin if the bad fan has a square pin
make sure you get a rectangle pin if the bad fan has a rectangular pin.
Hmm, maybe just getting the fan is less trouble than trying to work with the vendor I purchased from.
I wonder... I have a ton of spare fans from L3's and S9's. Will they work here?
you lost a fan it happens. buy a fan and replace it.
https://altairtech.io/product/antminer-120mm-replacement-fan-for-s19-s17-s11-s15-and-s9-series/
make sure you get a square pin if the bad fan has a square pin
make sure you get a rectangle pin if the bad fan has a rectangular pin.
https://altairtech.io/product/antminer-120mm-replacement-fan-for-s19-s17-s11-s15-and-s9-series/
make sure you get a square pin if the bad fan has a square pin
make sure you get a rectangle pin if the bad fan has a rectangular pin.
Applied a firmware update (Antminer-S19k-Pro-merge-release-20240409060820.bmu), now I get:
So I got a unit with a bad fan? Is the ASIC fine?
Code:
2025-01-08 18:42:54 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 4
2025-01-08 18:42:54 start do_core_reset
2025-01-08 18:43:06 end do_core_reset
2025-01-08 18:43:06 noraml inc freq voltage
2025-01-08 18:43:06 set_voltage_by_steps to 1500.
2025-01-08 18:43:10 Version num 65536
2025-01-08 18:43:10 Mask num 0x1fffe000
2025-01-08 18:43:10 opt_multi_version = 65536, interval timeout = 2620657
2025-01-08 18:43:10 freq = 590, percent = 90, hcn = 4442, timeout = 2620657
2025-01-08 18:43:10 (null)
2025-01-08 18:43:21 freq 200 waiting board temp to 35,curr temp 24
2025-01-08 18:43:23 Error, fan lost, only find 3 (< 4)
2025-01-08 18:43:23 fan_id = 0, fan_speed = 1990
2025-01-08 18:43:23 fan_id = 1, fan_speed = 0
2025-01-08 18:43:23 fan_id = 2, fan_speed = 2400
2025-01-08 18:43:23 fan_id = 3, fan_speed = 2400
2025-01-08 18:43:23 Sweep error string = F:1.
2025-01-08 18:43:23 ERROR_FAN_LOST: fan lost
2025-01-08 18:43:23 stop_mining: fan lost
2025-01-08 18:43:23 uninit_temp_info
2025-01-08 18:43:23 do not read temp anymore...
2025-01-08 18:43:23 cancel thread
2025-01-08 18:43:23 cancel thread
2025-01-08 18:43:23 ****power off hashboard****
2025-01-08 18:43:23 power off
2025-01-08 18:43:25 temp monitor thread exit
2025-01-08 18:43:31 freq 200 waiting board temp to 35,curr temp 24
2025-01-08 18:43:42 Sweep error string = P:2.
2025-01-08 18:43:42 ERROR_TEMP_TOO_LOW: protect machine!
2025-01-08 18:43:42 stop_mining: protect machine!
2025-01-08 18:43:42 ****power off hashboard****
2025-01-08 18:43:42 power off
So I got a unit with a bad fan? Is the ASIC fine?
It was working fine for about 4 days. Put it on sleep mode about a day ago, and turned it back on. Now, it's giving this:
Also noticed this in the historical log
What happened? The room temperature never exceeds 75F, and the current room temp is 61F. Other S19k's still humming along nicely.
Did I receive a bad unit?
Firmware Version Mon Mar 4 16:03:40 CST 2024
Already tried the basic troubleshooting (reboot, factory reset, power cycle)
Code:
2025-01-08 17:51:00 no board pluged in socket 432
...
2025-01-08 17:51:51 Error, fan lost, only find 3 (< 4)
2025-01-08 17:51:51 fan_id = 0, fan_speed = 7000
2025-01-08 17:51:51 fan_id = 1, fan_speed = 3440
2025-01-08 17:51:51 fan_id = 2, fan_speed = 5168
2025-01-08 17:51:51 fan_id = 3, fan_speed = 6020
2025-01-08 17:51:51 Sweep error string = F:1.
2025-01-08 17:51:51 ERROR_FAN_LOST: fan lost
2025-01-08 17:51:51 stop_mining: fan lost
2025-01-08 17:51:51 cancel thread
2025-01-08 17:51:51 ****power off hashboard****
2025-01-08 17:51:51 power off
2025-01-08 17:51:52 ERROR_SOC_INIT: soc init failed!
2025-01-08 17:51:52 stop_mining: soc init failed!
2025-01-08 17:51:52 ****power off hashboard****
2025-01-08 17:51:52 power off
Also noticed this in the historical log
Code:
2025-01-05 19:04:20 chain[2] asic[5] [215] [0]
2025-01-05 19:04:20 chain[2] bad asic num: 6 6 0
2025-01-05 19:04:20 chain[2] asic[5] [215] 28651771-28651556 [0] 62-62
What happened? The room temperature never exceeds 75F, and the current room temp is 61F. Other S19k's still humming along nicely.
Did I receive a bad unit?
Firmware Version Mon Mar 4 16:03:40 CST 2024
Already tried the basic troubleshooting (reboot, factory reset, power cycle)
Jump to: