Author

Topic: No hasboard after power shortage - Antminer S9 (Read 224 times)

legendary
Activity: 2030
Merit: 1569
CLEAN non GPL infringing code made in Rust lang
Thank you everyone for answering. I figured out that dusting was the issue. Its just weird because like 15 miners went situation like that at the same time. The issue is resolved by cleaning them up nicely. Did not know these devices are so sensitive to dusting

Eh? Well if you are in a low humidity climate dust might cause static, but it also prevents proper heat dissipation. Schedule periodic cleaning to all your miners, and remember to never let any fans spin (while connected) when cleaning with air blower, etc.
jr. member
Activity: 60
Merit: 1
Thank you everyone for answering. I figured out that dusting was the issue. Its just weird because like 15 miners went situation like that at the same time. The issue is resolved by cleaning them up nicely. Did not know these devices are so sensitive to dusting
legendary
Activity: 2394
Merit: 6581
be constructive or S.T.F.U
If this happened right after a power outage, then chances are PSU and/or those boards are toasted, but you need to go through the normal procedure of troubleshooting, in this order

1- Try a working PSU.
2- Try a working Control Board.
3- Different Firmware.
4- Reset.


if i had one shot, i would go for PSU , but it could be anything else, so after having done the basic troubleshooting, let us know the results.
legendary
Activity: 2030
Merit: 1569
CLEAN non GPL infringing code made in Rust lang
Hello, one of my miners does not have Hashboard found and has 0 TH/s after power shortage. Also 3 of them has 1-2 hashboards. Before that power shortage(Power went off and then back on after some while) all miners were working just fine with 3 boards 13.5 TH/s.
Here kernel log of 0 Hash board S9;
I hope someone knows what the issue is and give me some opinions..

Take a working miner, take all its asic boards out, and then test them all the asic boards from all your miners one by one there, so you can know for sure which ones are working.

After that, with a single known working asic board, test your controllers, also one by one (either move the asic board around or the controller, doesn't matter.

Its important to test them one by one before continuing, so you know what works and what doesn't.

Finally, with a known working controller with its 3 asic working boards, test each psu from all your miners one by one.

At the end you are going to know exactly what (if any) asic boards, controllers, and PSUs got damaged (if any), and take informed decisions.


Of course this is only with faulty miners plus a good one, if you have several good ones there is no need to check those.
legendary
Activity: 3374
Merit: 3095
Playbet.io - Crypto Casino and Sportsbook
There are two possible reasons why you are getting 0TH/s or no ASIC on all chains.

- The miner might have corrupted program
- Hardware issue on the hashboard or control board or possible PSU not giving enough power.


The first thing you need to do to troubleshoot and solve the issue is to follow my procedure below.

- First do a hard reset by holding the IPreport/reset button for 15 to 20 seconds it will automatically reboot. Make sure you run the miner in 5 minutes before you perform this hard reset. Set the pool then test

- Flash the miner with "Antminer-S9-all-201711171757-autofreq-user-Update2UBI-NF.tar.gz" then test it again.


If these method doesn't work you might have a hardware issue.

Try this method below.

- If you have extra miner try to swap the PSU and test.
- Check the 18 pin ribbon cable replace them with working one.
- Or test the hashboard one by one follow the procedure here Test hash board one by one if you have working s9 swap the hashboard then test.
jr. member
Activity: 60
Merit: 1
Hello, one of my miners does not have Hashboard found and has 0 TH/s after power shortage. Also 3 of them has 1-2 hashboards. Before that power shortage(Power went off and then back on after some while) all miners were working just fine with 3 boards 13.5 TH/s.
Here kernel log of 0 Hash board S9;
I hope someone knows what the issue is and give me some opinions..

Code:
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.0-xilinx-g16220c3 (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #83 SMP PREEMPT Thu Jul 12 11:42:53 CST 2018
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Xilinx Zynq
[    0.000000] cma: CMA: reserved 128 MiB at 16800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 126976
[    0.000000] free_area_init_node: node 0, pgdat c074ac00, node_mem_map debd8000
[    0.000000]   Normal zone: 992 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 126976 pages, LIFO batch:31
[    0.000000] PERCPU: Embedded 8 pages/cpu @debc1000 s9088 r8192 d15488 u32768
[    0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 125984
[    0.000000] Kernel command line: noinitrd mem=496M console=ttyPS0,115200 root=ubi0:rootfs ubi.mtd=1 rootfstype=ubifs rw rootwait
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 364316K/507904K available (5057K kernel code, 284K rwdata, 1928K rodata, 204K init, 258K bss, 143588K reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xdf800000 - 0xff000000   ( 504 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xdf000000   ( 496 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06da8ac   (6987 kB)
[    0.000000]       .init : 0xc06db000 - 0xc070e380   ( 205 kB)
[    0.000000]       .data : 0xc0710000 - 0xc0757138   ( 285 kB)
[    0.000000]        .bss : 0xc0757144 - 0xc0797bfc   ( 259 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[    0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] ps7-slcr mapped to df802000
[    0.000000] zynq_clock_init: clkc starts at df802100
[    0.000000] Zynq clock init
[    0.000014] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[    0.000295] ps7-ttc #0 at df804000, irq=43
[    0.000600] Console: colour dummy device 80x30
[    0.000630] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[    0.040199] pid_max: default: 32768 minimum: 301
[    0.040406] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.040425] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.042605] CPU: Testing write buffer coherency: ok
[    0.042927] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.042984] Setting up static identity map for 0x4cb118 - 0x4cb170
[    0.043203] L310 cache controller enabled
[    0.043223] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[    0.120986] CPU1: Booted secondary processor
[    0.210220] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.210351] Brought up 2 CPUs
[    0.210369] SMP: Total of 2 processors activated.
[    0.210378] CPU: All CPU(s) started in SVC mode.
[    0.211031] devtmpfs: initialized
[    0.213465] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    0.214666] regulator-dummy: no parameters
[    0.221672] NET: Registered protocol family 16
[    0.223906] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.226179] cpuidle: using governor ladder
[    0.226192] cpuidle: using governor menu
[    0.233585] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[    0.235102] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.235115] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.235228] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xdf880000
[    0.256831] bio: create slab at 0
[    0.258215] vgaarb: loaded
[    0.258898] SCSI subsystem initialized
[    0.259790] usbcore: registered new interface driver usbfs
[    0.259960] usbcore: registered new interface driver hub
[    0.260179] usbcore: registered new device driver usb
[    0.261576] media: Linux media interface: v0.10
[    0.261735] Linux video capture interface: v2.00
[    0.261982] pps_core: LinuxPPS API ver. 1 registered
[    0.261994] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[    0.262116] PTP clock support registered
[    0.262462] EDAC MC: Ver: 3.0.0
[    0.263649] Advanced Linux Sound Architecture Driver Initialized.
[    0.266384] DMA-API: preallocated 4096 debug entries
[    0.266398] DMA-API: debugging enabled by kernel config
[    0.266470] Switched to clocksource arm_global_timer
[    0.286548] NET: Registered protocol family 2
[    0.287201] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    0.287258] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.287343] TCP: Hash tables configured (established 4096 bind 4096)
[    0.287390] TCP: reno registered
[    0.287407] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.287439] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.287677] NET: Registered protocol family 1
[    0.288011] RPC: Registered named UNIX socket transport module.
[    0.288023] RPC: Registered udp transport module.
[    0.288031] RPC: Registered tcp transport module.
[    0.288039] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.288052] PCI: CLS 0 bytes, default 64
[    0.288480] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    0.290488] futex hash table entries: 512 (order: 3, 32768 bytes)
[    0.292571] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.292751] msgmni has been set to 967
[    0.293512] io scheduler noop registered
[    0.293525] io scheduler deadline registered
[    0.293566] io scheduler cfq registered (default)
[    0.302403] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[    0.302423] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[    0.425893] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[    0.993072] console [ttyPS0] enabled
[    0.997341] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to df866000
[    1.004947] [drm] Initialized drm 1.1.0 20060810
[    1.022031] brd: module loaded
[    1.031536] loop: module loaded
[    1.040936] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    1.046938] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    1.054679] libphy: XEMACPS mii bus: probed
[    1.059081] ------------- phy_id = 0x3625e62
[    1.063785] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[    1.072395] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.079172] ehci-pci: EHCI PCI platform driver
[    1.086384] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[    1.093218] usbcore: registered new interface driver usb-storage
[    1.100082] mousedev: PS/2 mouse device common for all mice
[    1.106155] i2c /dev entries driver
[    1.113077] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[    1.118594] cpufreq_cpu0: failed to get cpu0 regulator: -19
[    1.124469] Xilinx Zynq CpuIdle Driver started
[    1.129355] sdhci: Secure Digital Host Controller Interface driver
[    1.135450] sdhci: Copyright(c) Pierre Ossman
[    1.139877] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.145605] mmc0: no vqmmc regulator found
[    1.149647] mmc0: no vmmc regulator found
[    1.186490] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[    1.195160] usbcore: registered new interface driver usbhid
[    1.200670] usbhid: USB HID core driver
[    1.205378] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    1.211672] nand: Micron MT29F2G08ABAEAWP
[    1.215640] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    1.221585] Bad block table found at page 131008, version 0x01
[    1.227801] Bad block table found at page 130944, version 0x01
[    1.233849] 3 ofpart partitions found on MTD device pl353-nand
[    1.239616] Creating 3 MTD partitions on "pl353-nand":
[    1.244721] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[    1.252792] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[    1.260109] 0x00000b000000-0x000010000000 : "upgrade-rootfs"
[    1.270866] TCP: cubic registered
[    1.274100] NET: Registered protocol family 17
[    1.278790] Registering SWP/SWPB emulation handler
[    1.284680] regulator-dummy: disabling
[    1.289011] UBI: attaching mtd1 to ubi0
[    1.816634] UBI: scanning is finished
[    1.828278] UBI: attached mtd1 (name "angstram-rootfs", size 144 MiB) to ubi0
[    1.835330] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.842127] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.848802] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.855641] UBI: good PEBs: 1152, bad PEBs: 0, corrupted PEBs: 0
[    1.861651] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.868762] UBI: max/mean erase counter: 12/7, WL threshold: 4096, image sequence number: 1885751282
[    1.877878] UBI: available PEBs: 0, total reserved PEBs: 1152, PEBs reserved for bad PEB handling: 40
[    1.887095] UBI: background thread "ubi_bgt0d" started, PID 1084
[    1.887100] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.891062] ALSA device list:
[    1.891065]   No soundcards found.
[    1.907409] UBIFS: background thread "ubifs_bgt0_0" started, PID 1086
[    1.978249] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.984173] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    1.993321] UBIFS: FS size: 128626688 bytes (122 MiB, 1013 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
[    2.003197] UBIFS: reserved for root: 0 bytes (0 KiB)
[    2.008232] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 169D5274-BC1D-448D-AF98-689AB312947D, small LPT model
[    2.019555] VFS: Mounted root (ubifs filesystem) on device 0:11.
[    2.026744] devtmpfs: mounted
[    2.029850] Freeing unused kernel memory: 204K (c06db000 - c070e000)
[    2.863296] random: dd urandom read with 1 bits of entropy available
[    3.246515]
[    3.246515] bcm54xx_config_init
[    3.856514]
[    3.856514] bcm54xx_config_init
[    6.857355] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[    6.863448] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[   21.147789] In axi fpga driver!
[   21.150857] request_mem_region OK!
[   21.154247] AXI fpga dev virtual address is 0xdf9fe000
[   21.159388] *base_vir_addr = 0xc51e
[   21.174131] In fpga mem driver!
[   21.177479] request_mem_region OK!
[   21.180987] fpga mem virtual address is 0xe2000000
[   21.985889]
[   21.985889] bcm54xx_config_init
[   22.615808]
[   22.615808] bcm54xx_config_init
[   25.616363] xemacps e000b000.ps7-ethernet: Set clk to 24999999 Hz
[   25.622381] xemacps e000b000.ps7-ethernet: link up (100/FULL)
[  272.639803] random: nonblocking pool is initialized
log_level = 4
This is XILINX board. Totalram:       507486208
Detect 512MB control board of XILINX
mmap axi_fpga_addr = 0xb6ff4000
axi_fpga_addr data = 0xc51e
mmap fpga_mem_addr = 0xb5ded000
forceFreq=-1 forceFlag=0
min work minertest[0]:912


DETECT HW version=0000c51e
miner ID : 80124d2e2c00885c
Miner Type = S9
AsicType = 1387
real AsicNum = 63
use critical mode to search freq...
get PLUG ON=0x000000e0
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x03
Check chain[6] PIC fw version=0x03
Check chain[7] PIC fw version=0x03
read pic freq and badcore num...
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[0] has core num=1
Chain[5] ASIC[1] has core num=1
Chain[5] ASIC[2] has core num=1
Chain[5] ASIC[3] has core num=1
Chain[5] ASIC[5] has core num=2
Chain[5] ASIC[6] has core num=1
Chain[5] ASIC[7] has core num=2
Chain[5] ASIC[8] has core num=1
Chain[5] ASIC[9] has core num=2
Chain[5] ASIC[10] has core num=1
Chain[5] ASIC[12] has core num=1
Chain[5] ASIC[13] has core num=1
Chain[5] ASIC[14] has core num=1
Chain[5] ASIC[15] has core num=1
Chain[5] ASIC[16] has core num=2
Chain[5] ASIC[17] has core num=1
Chain[5] ASIC[18] has core num=2
Chain[5] ASIC[19] has core num=1
Chain[5] ASIC[21] has core num=1
Chain[5] ASIC[22] has core num=1
Chain[5] ASIC[23] has core num=1
Chain[5] ASIC[24] has core num=1
Chain[5] ASIC[25] has core num=1
Chain[5] ASIC[26] has core num=1
Chain[5] ASIC[27] has core num=1
Chain[5] ASIC[28] has core num=1
Chain[5] ASIC[29] has core num=9
Chain[5] ASIC[30] has core num=1
Chain[5] ASIC[31] has core num=1
Chain[5] ASIC[32] has core num=1
Chain[5] ASIC[33] has core num=2
Chain[5] ASIC[34] has core num=1
Chain[5] ASIC[35] has core num=1
Chain[5] ASIC[36] has core num=1
Chain[5] ASIC[37] has core num=1
Chain[5] ASIC[38] has core num=1
Chain[5] ASIC[39] has core num=1
Chain[5] ASIC[40] has core num=1
Chain[5] ASIC[41] has core num=1
Chain[5] ASIC[42] has core num=1
Chain[5] ASIC[43] has core num=2
Chain[5] ASIC[44] has core num=1
Chain[5] ASIC[45] has core num=2
Chain[5] ASIC[46] has core num=1
Chain[5] ASIC[47] has core num=1
Chain[5] ASIC[48] has core num=2
Chain[5] ASIC[49] has core num=1
Chain[5] ASIC[50] has core num=1
Chain[5] ASIC[51] has core num=1
Chain[5] ASIC[52] has core num=1
Chain[5] ASIC[53] has core num=1
Chain[5] ASIC[54] has core num=1
Chain[5] ASIC[55] has core num=1
Chain[5] ASIC[56] has core num=1
Chain[5] ASIC[57] has core num=1
Chain[5] ASIC[58] has core num=1
Chain[5] ASIC[59] has core num=1
Chain[5] ASIC[60] has core num=1
Chain[5] ASIC[61] has core num=1
Chain[5] ASIC[62] has core num=1
Check chain[5] PIC fw version=0x03
read pic freq and badcore num...
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[5] has core num=1
Chain[6] ASIC[6] has core num=3
Chain[6] ASIC[10] has core num=1
Chain[6] ASIC[12] has core num=1
Chain[6] ASIC[14] has core num=1
Chain[6] ASIC[16] has core num=1
Chain[6] ASIC[18] has core num=1
Chain[6] ASIC[21] has core num=2
Chain[6] ASIC[22] has core num=5
Chain[6] ASIC[23] has core num=1
Chain[6] ASIC[24] has core num=1
Chain[6] ASIC[25] has core num=1
Chain[6] ASIC[26] has core num=15
Chain[6] ASIC[27] has core num=1
Chain[6] ASIC[28] has core num=1
Chain[6] ASIC[29] has core num=1
Chain[6] ASIC[31] has core num=1
Chain[6] ASIC[32] has core num=1
Chain[6] ASIC[33] has core num=2
Chain[6] ASIC[34] has core num=2
Chain[6] ASIC[35] has core num=1
Chain[6] ASIC[36] has core num=1
Chain[6] ASIC[37] has core num=1
Chain[6] ASIC[38] has core num=1
Chain[6] ASIC[39] has core num=1
Chain[6] ASIC[40] has core num=1
Chain[6] ASIC[41] has core num=15
Chain[6] ASIC[42] has core num=5
Chain[6] ASIC[43] has core num=2
Chain[6] ASIC[44] has core num=2
Chain[6] ASIC[47] has core num=1
Chain[6] ASIC[50] has core num=1
Chain[6] ASIC[51] has core num=3
Chain[6] ASIC[53] has core num=5
Chain[6] ASIC[56] has core num=3
Chain[6] ASIC[57] has core num=2
Chain[6] ASIC[60] has core num=1
Check chain[6] PIC fw version=0x03
read pic freq and badcore num...
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Chain[7] ASIC[0] has core num=1
Chain[7] ASIC[1] has core num=1
Chain[7] ASIC[2] has core num=1
Chain[7] ASIC[3] has core num=2
Chain[7] ASIC[4] has core num=1
Chain[7] ASIC[5] has core num=1
Chain[7] ASIC[7] has core num=1
Chain[7] ASIC[8] has core num=1
Chain[7] ASIC[9] has core num=1
Chain[7] ASIC[10] has core num=1
Chain[7] ASIC[13] has core num=5
Chain[7] ASIC[14] has core num=1
Chain[7] ASIC[15] has core num=1
Chain[7] ASIC[16] has core num=1
Chain[7] ASIC[18] has core num=1
Chain[7] ASIC[19] has core num=1
Chain[7] ASIC[20] has core num=1
Chain[7] ASIC[21] has core num=1
Chain[7] ASIC[22] has core num=1
Chain[7] ASIC[23] has core num=1
Chain[7] ASIC[24] has core num=1
Chain[7] ASIC[25] has core num=1
Chain[7] ASIC[26] has core num=2
Chain[7] ASIC[27] has core num=3
Chain[7] ASIC[28] has core num=1
Chain[7] ASIC[29] has core num=8
Chain[7] ASIC[30] has core num=2
Chain[7] ASIC[33] has core num=1
Chain[7] ASIC[34] has core num=1
Chain[7] ASIC[35] has core num=1
Chain[7] ASIC[36] has core num=1
Chain[7] ASIC[37] has core num=1
Chain[7] ASIC[38] has core num=1
Chain[7] ASIC[39] has core num=1
Chain[7] ASIC[41] has core num=1
Chain[7] ASIC[43] has core num=1
Chain[7] ASIC[44] has core num=1
Chain[7] ASIC[45] has core num=7
Chain[7] ASIC[46] has core num=1
Chain[7] ASIC[47] has core num=1
Chain[7] ASIC[48] has core num=2
Chain[7] ASIC[51] has core num=1
Chain[7] ASIC[52] has core num=1
Chain[7] ASIC[53] has core num=1
Chain[7] ASIC[54] has core num=1
Chain[7] ASIC[56] has core num=1
Chain[7] ASIC[57] has core num=1
Chain[7] ASIC[58] has core num=1
Chain[7] ASIC[60] has core num=1
Chain[7] ASIC[61] has core num=1
Chain[7] ASIC[62] has core num=1
Check chain[7] PIC fw version=0x03
get PIC voltage=6 on chain[5], value=940
get PIC voltage=6 on chain[6], value=940
get PIC voltage=6 on chain[7], value=940
chain[5] temp offset record: 62,0,0,0,0,0,35,28
chain[5] temp chip I2C addr=0x98
chain[5] has no middle temp, use special fix mode.
chain[6] temp offset record: 62,0,0,0,0,0,35,28
chain[6] temp chip I2C addr=0x98
chain[6] has no middle temp, use special fix mode.
chain[7] temp offset record: 62,0,0,0,0,0,35,28
chain[7] temp chip I2C addr=0x98
chain[7] has no middle temp, use special fix mode.
total_exist_chain_num = 3
CRC error counter=0
set command mode to VIL

--- check asic number
After Get ASIC NUM CRC error counter=0
set_baud=0
The min freq=700
set real timeout 52, need sleep=379392
After TEST CRC error counter=0
search freq for 1 times, completed chain = 3, total chain num = 3
single_board_frq_tuning enter
min_rate, des_rate, fix_volt:13800, 14000, 880
force_freq not set, don't need tuning
restart Miner chance num=2
waiting for receive_func to exit!
waiting for pic heart to exit!
bmminer not found=17065 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found=  763 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
bmminer not found=10108 root       0:00 grep bmminer

bmminer not found, restart bmminer ...
This is user mode for mining
Detect 512MB control board of XILINX
Miner Type = S9
Miner compile time: Mon Mar 4 11:37:08 CST 2019 type: Antminer S9set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
set_reset_allhashboard = 0x0000ffff
miner ID : 80124d2e2c00885c
set_reset_allhashboard = 0x0000ffff
Checking fans!get fan[4] speed=6000
get fan[4] speed=6000
get fan[4] speed=6000
get fan[5] speed=4320
get fan[4] speed=6000
get fan[5] speed=4320
get fan[4] speed=6000
get fan[5] speed=4320
chain[5]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J6] has backup chain_voltage=870
Check chain[5] PIC fw version=0x03
chain[6]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J7] has backup chain_voltage=870
Check chain[6] PIC fw version=0x03
chain[7]: [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255] [63:255]
Detect: use voltage limit rules on single board!
Detect: S9_63 use voltage level=3 : 0
Chain[J8] has backup chain_voltage=890
Check chain[7] PIC fw version=0x03
Chain[J6] orignal chain_voltage_pic=6 value=940
Chain[J6] will use backup chain_voltage_pic=870 [125]
Chain[J6] get working chain_voltage_pic=125
Chain[J7] orignal chain_voltage_pic=6 value=940
Chain[J7] will use backup chain_voltage_pic=870 [125]
Chain[J7] get working chain_voltage_pic=125
Chain[J8] orignal chain_voltage_pic=6 value=940
Chain[J8] will use backup chain_voltage_pic=890 [91]
Chain[J8] get working chain_voltage_pic=91
set_reset_allhashboard = 0x0000ffff
set_reset_allhashboard = 0x00000000
Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
set_reset_hashboard = 0x00000020
set_reset_hashboard = 0x00000000
retry Chain[J6] has 0 asic
Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
set_reset_hashboard = 0x00000040
set_reset_hashboard = 0x00000000
retry Chain[J7] has 0 asic
Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
set_reset_hashboard = 0x00000080
set_reset_hashboard = 0x00000000
retry Chain[J8] has 0 asic
miner total rate=0GH/s fixed rate=0GH/s

Miner fix freq ...
max freq = 100
set baud=1
do heat board 8xPatten for 1 times
setStartTimePoint total_tv_start_sys=1024 total_tv_end_sys=1025
restartNum = 2 , auto-reinit enabled...
do read_temp_func once...
do check_asic_reg 0x08
Done check_asic_reg
set FAN speed according to: temp_highest=0 temp_top1[PWM_T]=0 temp_top1[TEMP_POS_LOCAL]=0 temp_change=0 fix_fan_steps=0
set full FAN speed...
FAN PWM: 100
read_temp_func Done!
CRC error counter=0
Jump to: