Nvidia GTX1060 + AMD RX580 Claymore ETHOS

mcoevoet

newbie

Activity: 5

Merit: 0

For those who could be interested, I finally succeed to run GTX1060 and RX580 together, via the config file Claymore.stub.conf:

-tt -70
-tt 30

Both parameters are usefull. It runs for more than 36 hours!

Happy new year ;-)!

Max

FalconZA

member

Activity: 182

Merit: 12

It could be the miner you using. I'm not familiar with Ethos, but this shouldn't be a problem on Windows with Claymore.

Perhaps load Windows with Claymore as a secondary boot option and see if it works?

storeship

newbie

Activity: 41

Merit: 0

I have 2 x GTX 1070 and 2 x RX 580 on my rig and only mines with the 580's it doesnt seem to want me to mix the GPU's?
If i remove the 580's it works with just the 1070's
It recognises all 4 cards when booting up?
I was under the impression you can mix cards on Ethos?

FalconZA

member

Activity: 182

Merit: 12

Quote from: mcoevoet on December 18, 2017, 10:19:44 AM

I have tried with only 1 GTX 1060 and 1 RX 580 in place of 2 RX 580 + 1 GTX 1050.

So, it seems the power supply has enough power to support at least 3 GPU ...

It mines correctly, until GPU temperature reach 61°C ... what is strange is that "-t 50" does not help in this configuration.
It works fine if GTX 1060 is alone ...

If someone understands this behavior ;-)

Regards,

Maxime

Did you place a temperature limit on your MSI afterburner?
Make -t 80 and see if temps still go that high.
What PSU do you have?

mcoevoet

newbie

Activity: 5

Merit: 0

I have tried with only 1 GTX 1060 and 1 RX 580 in place of 2 RX 580 + 1 GTX 1050.

So, it seems the power supply has enough power to support at least 3 GPU ...

It mines correctly, until GPU temperature reach 61°C ... what is strange is that "-t 50" does not help in this configuration.
It works fine if GTX 1060 is alone ...

If someone understands this behavior ;-)

Regards,

Maxime

FalconZA

member

Activity: 182

Merit: 12

That doesn't sound right? You sure your PSU could handle the loads to both GPUs? I had 580s and 1060 running fine together in the past. R9 280X with 1060s also.

mcoevoet

newbie

Activity: 5

Merit: 0

Thanks!

I already tried ... my conclusions are that RX580 + GTX1060 does not work ... it's fine with GTX1050, but not 1060.
I have configured a second miner so for NVIDIA ...

Maxime

0xcosmos

full member

Activity: 585

Merit: 110

Quote from: mcoevoet on December 11, 2017, 08:13:58 AM

Hi,

thanks for proposals.
I did used this config: https://www.zotac.com/us/product/graphics_card/zotac-geforce-gtx-1060-amp-edition#spec
I started with the smallest frequency without any success.

Unfortunately, there are not a lot of tools to check the GPU fan speed under ETHOS.

Does Claymore should be able to work with this config from a technical point of view?

Best regards,

Maxime

yes you can use claymore miner to set fan speeds for your gpus
just add this syntax -ti -50
for 50 percent fan speed
and you can also use it for underclock and overclock too

mcoevoet

newbie

Activity: 5

Merit: 0

Hi,

thanks for proposals.
I did used this config: https://www.zotac.com/us/product/graphics_card/zotac-geforce-gtx-1060-amp-edition#spec
I started with the smallest frequency without any success.

Unfortunately, there are not a lot of tools to check the GPU fan speed under ETHOS.

Does Claymore should be able to work with this config from a technical point of view?

Best regards,

Maxime

0xcosmos

full member

Activity: 585

Merit: 110

i hope you are not overclocking much
did you check the memory vendor of your gtx 1060?
is it hynix or micron or samsung or elphida?
because how much a card can overclock will depend on it

FalconZA

member

Activity: 182

Merit: 12

I've never experienced this before. Best way would be to manually set your GPU fan speed on afterburner (or whatever overclocking tool you use). Keep it at a % that keep your temps where you want them (50-65 C). That way you can ensure you card doesn't overheat and give you those errors. If that doesn't work you could ask on their Discord channel.

mcoevoet

newbie

Activity: 5

Merit: 0

Hi,

I spent a long time to succeed mining with a mix of NVIDIA + AMD card (GTX 1060 + RX 580).

Everything goes fine until GTX 1060 reach 61°C ... then fan speed is about 11%, and after 1 or 2 minutes, GPU crash!
I get this error message: "nvml cannot get current temperature error 15".

Reboot, and back again to crash after a while.

I tried to adjust parameters in local.conf to reduce memClock or coreClock ... unsuccessfull.
I tried different solution in claymore.stub.conf ... same results.

Does someone did experiment same config, issue? (ethos, NVIDIA + AMD using Claymore).
Do I have to use another miner algo?

Many thanks!

Maxime

Topic: Nvidia GTX1060 + AMD RX580 Claymore ETHOS (Read 360 times)