They're also particularly well suited to high-density 3U/4U rackmount servers where noise isn't a real concern - a couple of these will keep a server full of high-load HDDs nice and frosty.
At 65dB+ they're not exactly meant to be in the rig under your desk.
Topic: Opinions on running delta fans at max load 24/7 (Read 1553 times)
Deltas and other 38mm thick fans have high AIR PRESSURE. So they will have a higher load per cubic foot than other fans optimized for volume over pressure.
Do you need high air pressure? It depends on what you are using the fan for. If just using it to blow across an unrestricted space to move hot air well no. There is very little reistence and the increased air pressure is wasted. If you are trying to blow across a restricted space (like force air through a high fin density radiator, or force more air through heatsink fins of a GPU then high air pressure may be worth it.
Do you need high air pressure? It depends on what you are using the fan for. If just using it to blow across an unrestricted space to move hot air well no. There is very little reistence and the increased air pressure is wasted. If you are trying to blow across a restricted space (like force air through a high fin density radiator, or force more air through heatsink fins of a GPU then high air pressure may be worth it.
The Deltas are no joke - I'm not surprised to see 24W at all.
Most normal high-flow case fans pull between 5-10W - for example I have a bunch of these 110CFM Scythe slipstreams that are about 6.3W each: http://www.sidewindercomputers.com/sc12slsy110c.html
[edit] Indeed, you need to be careful to balance power for the Deltas - most fan controllers will allow about 20W per channel - a single one of those Deltas at full-speed/12V can burn out your controller
[edit] bad math - the scythes are 6.3W, not 8.6W - which makes the Delta's draw even more crazy
Most normal high-flow case fans pull between 5-10W - for example I have a bunch of these 110CFM Scythe slipstreams that are about 6.3W each: http://www.sidewindercomputers.com/sc12slsy110c.html
[edit] Indeed, you need to be careful to balance power for the Deltas - most fan controllers will allow about 20W per channel - a single one of those Deltas at full-speed/12V can burn out your controller
[edit] bad math - the scythes are 6.3W, not 8.6W - which makes the Delta's draw even more crazy
Well its what I got when I googled 120mm delta fans that matched ~190cfm. I found this one:
http://www.sidewindercomputers.com/delffb1212eh.html
They may have more power efficient fans, but no fan is going to sip power and achieve that kind of airflow.
http://www.sidewindercomputers.com/delffb1212eh.html
They may have more power efficient fans, but no fan is going to sip power and achieve that kind of airflow.
Really? I thought they were 8 - 10w. I will have to revisit those fans and see. Jeez... 24w each?
I'm only running two per rig, but that still adds up across 6 rigs.
I'm only running two per rig, but that still adds up across 6 rigs.
Just as a side remark, those fans will use up to 24W each. Thats ~100W per rig for case fans only. Not nothing. You sure you need that much? If you have to pay for electricty Id (re)consider open frame rigs.
Quote
Great fans. Just secure them where you expect them to go. Otherwise you end up a fucking angry catfish with two expensive fans with snapped blades because they were balanced on two crappy XFX cards that were overheating, wiggled a bit and the rotor smacked into something hard.
The plastic the fans use is brittle and a slight impact at the speed they go will destroy them instantly. I know this through experience.
I've pretty much lost half my mining profit now due to hardware failures - most due to XFX, but self-destructing fans aren't fun either.
The plastic the fans use is brittle and a slight impact at the speed they go will destroy them instantly. I know this through experience.
I've pretty much lost half my mining profit now due to hardware failures - most due to XFX, but self-destructing fans aren't fun either.
At least you only lost hardware... I have scars on my fingers from almost losing them in the fans
Quote
Great fans. Just secure them where you expect them to go. Otherwise you end up a fucking angry catfish with two expensive fans with snapped blades because they were balanced on two crappy XFX cards that were overheating, wiggled a bit and the rotor smacked into something hard.
The plastic the fans use is brittle and a slight impact at the speed they go will destroy them instantly. I know this through experience.
I've pretty much lost half my mining profit now due to hardware failures - most due to XFX, but self-destructing fans aren't fun either.
The plastic the fans use is brittle and a slight impact at the speed they go will destroy them instantly. I know this through experience.
I've pretty much lost half my mining profit now due to hardware failures - most due to XFX, but self-destructing fans aren't fun either.
XFX man, same here, Im laiden with a 6870 and 6950 cause of XFX's failing on me. Got 1 left and it didnt sound healthy this morning tbh. Bit of a squel from the fan..... AGAIN! Let this be a warning to people
Sapphire have really impressed me in hardware/price(most times) and OC'ing ability and there trixx is alright. Nice and easy. Back on topic, Delta's are ACE
I had a delta years back. Awesome fans, NOISEY AS HELL, but if thats not an issue, you dont get better. Man, i put in on the CPU the wrong way, Was like a tornado Had to change it as it was for a gaming PC and could hear it downstairs even when throttled lol
Had to change it as it was for a gaming PC and could hear it downstairs even when throttled lol
Deltas are beasts and are meant to have long lifetimes under full load.
Keep them clean, and keep them lubricated, and they'll last you next to forever.
There's usually a lubricant port underneath the sticker on the hub, just squeeze in a drop every 3-6 mo or so, you can probably go a lot longer but hey, it's a cheap way to keep 'em spinning for a long, long time.
Keep them clean, and keep them lubricated, and they'll last you next to forever.
There's usually a lubricant port underneath the sticker on the hub, just squeeze in a drop every 3-6 mo or so, you can probably go a lot longer but hey, it's a cheap way to keep 'em spinning for a long, long time.
Delta is like server quality. server fans run at 100% 24/7/365 and they don't have problems. fwiw I have this http://www.sidewindercomputers.com/de12tfexhisp.html
Is there anyone here running delta fans on their rigs? I have four on each rig moving 192cfm of cool air over the cards at fairly high pressure.
These 120mm delta fans are ball bearing type and are at max load - Will I have any problems running them at max load like this all the time?
Thanks.
These 120mm delta fans are ball bearing type and are at max load - Will I have any problems running them at max load like this all the time?
Thanks.
Jump to: