Hi what if i like to have default cvddc / mvddc
If you want to keep default memory and core voltages then just don't add -cvddc / -mvddc in your .bat file.
But you will have higher power consumption.
Topic: Overclocking with batchfile (Read 482 times)
If you want to keep default memory and core voltages then just don't add -cvddc / -mvddc in your .bat file.
But you will have higher power consumption.
Okay many thanks. I experienced some crashes at the beginning with 850 so I left the mem and core voltages apart and tweaked the memory and core clocks first, but I'll add the mem and core voltages slowly like you explained.
I want to run my GPUs with only 80% of their original power draw. Should I rather setup -powlim or -cvddc and - mvddc?
-powlim set power limit, from -50 to 50. If not specified, miner will not change power limit. You can also specify values for every card, for example "-powlim 20,-20,0,10".
Note: for NVIDIA cards this option is not supported.
-cvddc set target GPU core voltage, multiplied by 1000. For example, "-cvddc 1050" means 1.05V. You can also specify values for every card, for example "-cvddc 900,950,1000,970". Supports latest AMD 4xx cards only in Windows.
Note: for NVIDIA cards this option is not supported.
-mvddc set target GPU memory voltage, multiplied by 1000. For example, "-mvddc 1050" means 1.05V. You can also specify values for every card, for example "-mvddc 900,950,1000,970". Supports latest AMD 4xx cards only in Windows.
Note: for NVIDIA cards this option is not supported.
What's the difference between target GPU core voltage and memory voltage? I didn't do any voltage settings so far, I only worked with power limit in MSI afterburner so far
They are pretty self explanatory terms, GPU core voltage is for the actual GPU processor itself (the chip) and memory voltage is for the actual memory chips on-board the GPU.
Most of the time these will be set the same values as each other, but for advanced tweaking they can be set to different values with the one caveat that the memory voltage cannot be lower than the core voltage.
To adjust the power level with AMD cards, it is recommend to adjust the voltages. You can probably start safely with 950 for both the core and memory (which represents 950 mv or 0.095 V) and work slowly down from there until your GPUs hang or crash. Then add back another 20 mv and you should be close to the sweet spot as far as energy saving versus power consumption. For example say you make it down to 850 mv before the cards hang, then you would bump your settings to 870 mv and run that for awhile to test for stability. It basically will take some trial and error as each system and graphic card will be different as to how much undervolting it will tolerate.
I want to run my GPUs with only 80% of their original power draw. Should I rather setup -powlim or -cvddc and - mvddc?
-powlim set power limit, from -50 to 50. If not specified, miner will not change power limit. You can also specify values for every card, for example "-powlim 20,-20,0,10".
Note: for NVIDIA cards this option is not supported.
-cvddc set target GPU core voltage, multiplied by 1000. For example, "-cvddc 1050" means 1.05V. You can also specify values for every card, for example "-cvddc 900,950,1000,970". Supports latest AMD 4xx cards only in Windows.
Note: for NVIDIA cards this option is not supported.
-mvddc set target GPU memory voltage, multiplied by 1000. For example, "-mvddc 1050" means 1.05V. You can also specify values for every card, for example "-mvddc 900,950,1000,970". Supports latest AMD 4xx cards only in Windows.
Note: for NVIDIA cards this option is not supported.
What's the difference between target GPU core voltage and memory voltage? I didn't do any voltage settings so far, I only worked with power limit in MSI afterburner so far
Great, many thanks for your posts! Good to know and much easier than I had imagined!
I'll try it out and hope my rig will not crash
I'll try it out and hope my rig will not crash
I want to overclock my RX 480 cards with the .bat file instead of using MSI Afterburner. I have several problems with Afterburner because I use the mining drivers and because I have 2 different GPU brands in my rig (2 XFX GTR with standard core clock 1388 and Powercolor Red Devil with standard core clock 1288) and the rig crashes when I OC different cards.
I found out that you can OC your GPU via the .bat file with this code:
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal ETHEREUM_WALLET.WORKER_NAME -epsw x -tstop 85 -tt 65 -fanmin 60 -fanmax 100 -cclock 1200 -mclock 2250 -cvddc 850 -mvddc 850
I wonder if it's possible to set different overclocks for each card in the .bat file? Is there a guide on using the .bat file overclocking somewhere?
I found out that you can OC your GPU via the .bat file with this code:
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal ETHEREUM_WALLET.WORKER_NAME -epsw x -tstop 85 -tt 65 -fanmin 60 -fanmax 100 -cclock 1200 -mclock 2250 -cvddc 850 -mvddc 850
I wonder if it's possible to set different overclocks for each card in the .bat file? Is there a guide on using the .bat file overclocking somewhere?
Yes it is possible to set overclock settings in the batchfile, but I, myself, am having trouble making the clock settings on batchfile to work on AMD cards. Is this because the rig has a combination of both NVidia and AMD cards?
Anyway, in order to do this, just add a "," after the first clock value.
For example -cclock 1200,1100,1300 -mclock 2100,2000,2100
Same applies to -cvddc -mvddc and other parameters like the intensity settings for single mining and dual mining. You can set all these settings individually in the batch file.
I want to overclock my RX 480 cards with the .bat file instead of using MSI Afterburner. I have several problems with Afterburner because I use the mining drivers and because I have 2 different GPU brands in my rig (2 XFX GTR with standard core clock 1388 and Powercolor Red Devil with standard core clock 1288) and the rig crashes when I OC different cards.
I found out that you can OC your GPU via the .bat file with this code:
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal ETHEREUM_WALLET.WORKER_NAME -epsw x -tstop 85 -tt 65 -fanmin 60 -fanmax 100 -cclock 1200 -mclock 2250 -cvddc 850 -mvddc 850
I wonder if it's possible to set different overclocks for each card in the .bat file? Is there a guide on using the .bat file overclocking somewhere?
I found out that you can OC your GPU via the .bat file with this code:
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal ETHEREUM_WALLET.WORKER_NAME -epsw x -tstop 85 -tt 65 -fanmin 60 -fanmax 100 -cclock 1200 -mclock 2250 -cvddc 850 -mvddc 850
I wonder if it's possible to set different overclocks for each card in the .bat file? Is there a guide on using the .bat file overclocking somewhere?
That line of code is used with the Claymore Ethereum miner and there is a ReadMe file inside its folder detailing each of the available commands.
To apply different settings to multiple cards, you simply separate the values for each card, so in your case with three cards with one of them being different, your batch file would look something like:
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal ETHEREUM_WALLET.WORKER_NAME -epsw x -tstop 85 -tt 65 -fanmin 60 -fanmax 100 -cclock 1200,1200,1100 -mclock 2250,2250,2000 -cvddc 850,850,900 -mvddc 850,850,900
I simply used random values for the clocks and voltages to give you an idea as you would need to use your own unique values, but in my example above the last value in -cclock would be for GPU 2 (counting starts at 0 as in 0,1,2), same for the other values. Since you have 3 cards you need three values, if you had 6 cards you would need 6 values and so on.
Also for any settings that will be the same for all your cards, like the tstop, tt, fanmin and fanmax, you can leave it a single number. A single value behind a parameter indicates it will apply to all the cards. Again, if you want different settings for each different card you would put multiple values behind the parameter as well, one for each card.
So the basic premise is one value following a parameter applies to all GPUs and if you want to have different values for for each card you would need to have a separate value for as many GPUs as you have.
I want to overclock my RX 480 cards with the .bat file instead of using MSI Afterburner. I have several problems with Afterburner because I use the mining drivers and because I have 2 different GPU brands in my rig (2 XFX GTR with standard core clock 1388 and Powercolor Red Devil with standard core clock 1288) and the rig crashes when I OC different cards.
I found out that you can OC your GPU via the .bat file with this code:
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal ETHEREUM_WALLET.WORKER_NAME -epsw x -tstop 85 -tt 65 -fanmin 60 -fanmax 100 -cclock 1200 -mclock 2250 -cvddc 850 -mvddc 850
I wonder if it's possible to set different overclocks for each card in the .bat file? Is there a guide on using the .bat file overclocking somewhere?
I found out that you can OC your GPU via the .bat file with this code:
EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal ETHEREUM_WALLET.WORKER_NAME -epsw x -tstop 85 -tt 65 -fanmin 60 -fanmax 100 -cclock 1200 -mclock 2250 -cvddc 850 -mvddc 850
I wonder if it's possible to set different overclocks for each card in the .bat file? Is there a guide on using the .bat file overclocking somewhere?
Jump to: