Topic: Pandaminer -> Linux -> Modded Roms (Read 16210 times)
it will work on simple mining no problem
Is in this chat people who use the program Simplemining on Panda the miner B3+ ?
@Eliovp can you provide a copy of the bios on those GPUs I see they use Hynix memory and I am interested on the timing on those.
Yeah he'll provide a copy once you buy it. lol
Some more results.
So XMR still at 4amps (880watt) after 15hrs.
Picture:
Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..)
I will test with genoil's as well later today.
236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now..
Picture:
Did a testrun for zcash as well.
1730H while consuming 4.9A (1078watt)
Picture:
Then i did some minor modifcations (rom wise)
Improved hashrate and same consumption.
So still 4A (880 watt) but this time hitting 6400h
Picture:
Again, overall, i must say, awesome machine.
This could be seriously interesting for bigger farms.
I made it so that i just plug in the power, it boots and starts mining.
Other algo, no problem. Switch and go.
Greetings!
So XMR still at 4amps (880watt) after 15hrs.
Picture:
Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..)
I will test with genoil's as well later today.
236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now..
Picture:
Did a testrun for zcash as well.
1730H while consuming 4.9A (1078watt)
Picture:
Then i did some minor modifcations (rom wise)
Improved hashrate and same consumption.
So still 4A (880 watt) but this time hitting 6400h
Picture:
Again, overall, i must say, awesome machine.
This could be seriously interesting for bigger farms.
I made it so that i just plug in the power, it boots and starts mining.
Other algo, no problem. Switch and go.
Greetings!
Hi there. Thank you so much for your posts, that's very good info. may I ask, how is working the system so far? It's been a couple of months since you got it right?
Basically let me know what do you think, is very stable? is worth for buying?
Besides XMR / ETH/ ZAC, is there any other cripto you've been able to mine as well?
Thanks in advance for your info!
Running like a champ. I have a few pandas and run XMR. I am about 6400 (800 a card ish) and sub 900 watts. I also had him write me one for my RX 6 card rigs and I am getting 4.5K on 640 watts!
@Eliovp can you provide a copy of the bios on those GPUs I see they use Hynix memory and I am interested on the timing on those.
Some more results.
So XMR still at 4amps (880watt) after 15hrs.
Picture:
Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..)
I will test with genoil's as well later today.
236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now..
Picture:
Did a testrun for zcash as well.
1730H while consuming 4.9A (1078watt)
Picture:
Then i did some minor modifcations (rom wise)
Improved hashrate and same consumption.
So still 4A (880 watt) but this time hitting 6400h
Picture:
Again, overall, i must say, awesome machine.
This could be seriously interesting for bigger farms.
I made it so that i just plug in the power, it boots and starts mining.
Other algo, no problem. Switch and go.
Greetings!
So XMR still at 4amps (880watt) after 15hrs.
Picture:
Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..)
I will test with genoil's as well later today.
236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now..
Picture:
Did a testrun for zcash as well.
1730H while consuming 4.9A (1078watt)
Picture:
Then i did some minor modifcations (rom wise)
Improved hashrate and same consumption.
So still 4A (880 watt) but this time hitting 6400h
Picture:
Again, overall, i must say, awesome machine.
This could be seriously interesting for bigger farms.
I made it so that i just plug in the power, it boots and starts mining.
Other algo, no problem. Switch and go.
Greetings!
Hi there. Thank you so much for your posts, that's very good info. may I ask, how is working the system so far? It's been a couple of months since you got it right?
Basically let me know what do you think, is very stable? is worth for buying?
Besides XMR / ETH/ ZAC, is there any other cripto you've been able to mine as well?
Thanks in advance for your info!
Hello!
how to enter the BIOS boot pandaminer?
that would put the switch on when power on?
enter the BIOS pandaminer
when you push the start button
Hold on delete key
that would put the switch on when power on?
enter the BIOS pandaminer
when you push the start button
Hold on delete key
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
Nope, they're directly connected to the mainboard.
I'm working on a sollution for this as i don't need them to run at 100%
Not going to hurt anything if they do, and helps keep things cooler for better longevity.
Now, if they were the GHE screamers I could see wanting to slow them down!
Have you checked to see if they even have speed control at all (4 wire interface)?
A lot of Deltas are 3-wire "tach output no PWM speed control capability only".
I vaguely recall Phil or someone else mentioning they were 3 pin wire fans, thus no speed control.
Let me look at photos I,took.
3 pin direct to power board two jacks on the power input. The fans appear to daisy chain four push five pull.
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
Nope, they're directly connected to the mainboard.
I'm working on a sollution for this as i don't need them to run at 100%
Not going to hurt anything if they do, and helps keep things cooler for better longevity.
Now, if they were the GHE screamers I could see wanting to slow them down!
Have you checked to see if they even have speed control at all (4 wire interface)?
A lot of Deltas are 3-wire "tach output no PWM speed control capability only".
I vaguely recall Phil or someone else mentioning they were 3 pin wire fans, thus no speed control.
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
Nope, they're directly connected to the mainboard.
I'm working on a sollution for this as i don't need them to run at 100%
Not going to hurt anything if they do, and helps keep things cooler for better longevity.
Now, if they were the GHE screamers I could see wanting to slow them down!
Have you checked to see if they even have speed control at all (4 wire interface)?
A lot of Deltas are 3-wire "tach output no PWM speed control capability only".
I opened a thread up to try to figure funding for Evliop's linux build for the PandaMiner
https://bitcointalksearch.org/topic/interest-thread-for-eliovp-linux-build-for-pandaminer-1740719
https://bitcointalksearch.org/topic/interest-thread-for-eliovp-linux-build-for-pandaminer-1740719
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
Nope, they're directly connected to the mainboard.
I'm working on a sollution for this as i don't need them to run at 100%
Hm seems like fans are not controlable ? Anyone mastered changing fanspeed on this panda ?
op and I have been kicking around ideas of how to work out a linux for pandaminer distribution.
I may start a separate thread.
I may start a separate thread.
if you are in Europe - how much they write on invoice? (because high VAT...)
30 $ for Case
10 $ for Fan
Thanks.
What EU customs code (Taric) you use?
i used nothing DHL showed up on my Door and asked for 37 Euro, i paid them, end of story.
I'm pretty sure Claymore isn't going to release anything for linux anymore. Perhaps he will, but i don't think so..
I'm running claymore's v9.3 ZEC miner on linux (ethOS), but can't speak for any of his other miners running on linux.
Edit: I just upgraded to claymore v9.3 and will check to see what flypool reports as my 24hour hash rate. Currently it reports 141.4 H/s.
upgrade from 9.2 to 9.3 produced a yawn. rate is the same at the pool after almost 24 hours.
if you are in Europe - how much they write on invoice? (because high VAT...)
30 $ for Case
10 $ for Fan
Thanks.
What EU customs code (Taric) you use?
It appears that they changed fans somewhere between the prototype (that used 7x or 8x Delta 60mm screamers - that ARE very good reliability) to 5x of some sort of an 80mm fan?
I've not seen any pictures that actually showed the actual fans on a production unit though.
I've not seen any pictures that actually showed the actual fans on a production unit though.
delta 80 mm they are loud but not nasty pitch they use .8 amps at 12 volt that is about 10 watts a fan
Sounds like one of their mid-range 80mm then - Delta makes a VERY WIDE range of fans - dozens in JUST 80mm alone, and I think a few hundred or so different models in total.
If one of the graphics does not work, can you buy a replacement from the market easily?
It's not that easy to find, but i bet my shirt pandaminer gonna have a parts shop
If one of the graphics does not work, can you buy a replacement from the market easily?
Linux + modded roms make this rig ALOT more interesting & attractive
BUT
i still cringe @ the 6 months warranty, if you don't pay for electricity you can ROI it just @ the end of the warranty, but if you do pay for it, it's gonna be longer. (ok some could argue after 6 months usually computer parts, especially if they ran for 6 months 24/7 shouldn't fail) but it still make me reluctant to try my luck....
Keep up the good work man anyway
BUT
i still cringe @ the 6 months warranty, if you don't pay for electricity you can ROI it just @ the end of the warranty, but if you do pay for it, it's gonna be longer. (ok some could argue after 6 months usually computer parts, especially if they ran for 6 months 24/7 shouldn't fail) but it still make me reluctant to try my luck....
Keep up the good work man anyway
Yeah, it does and thx
Anyhow, they have a good decent product, the only thing they lack is marketing and a decent after sales policy..
We'll see, perhaps they'll come to their senses..
Linux + modded roms make this rig ALOT more interesting & attractive
BUT
i still cringe @ the 6 months warranty, if you don't pay for electricity you can ROI it just @ the end of the warranty, but if you do pay for it, it's gonna be longer. (ok some could argue after 6 months usually computer parts, especially if they ran for 6 months 24/7 shouldn't fail) but it still make me reluctant to try my luck....
Keep up the good work man anyway
BUT
i still cringe @ the 6 months warranty, if you don't pay for electricity you can ROI it just @ the end of the warranty, but if you do pay for it, it's gonna be longer. (ok some could argue after 6 months usually computer parts, especially if they ran for 6 months 24/7 shouldn't fail) but it still make me reluctant to try my luck....
Keep up the good work man anyway
I'm finding it harder and harder to resist ordering one of these from your review and Phil's.
Super!!!
If this Pandaminer hits this high of H/s with 4 to 6 Amps.... and those temperature readings are fantastic for a high end rig.
I can only imagine what alien technology heatsinks are used by Panda.
I think its a very big milestone for GPU farm in terms of hash/power/footprint/serviceability.
What settings sgminer-gm? rawintesity 512 -w 4 -g 2 ?
Cant wait for my Panda arriving tomorrow morning.
If this Pandaminer hits this high of H/s with 4 to 6 Amps.... and those temperature readings are fantastic for a high end rig.
I can only imagine what alien technology heatsinks are used by Panda.
I think its a very big milestone for GPU farm in terms of hash/power/footprint/serviceability.
What settings sgminer-gm? rawintesity 512 -w 4 -g 2 ?
Cant wait for my Panda arriving tomorrow morning.
Lego it is!
Some more modifications (again rom wise)
Almost 800h per card
(not giving up!)
Still 4A!!
Some more modifications (again rom wise)
Almost 800h per card
(not giving up!)Still 4A!!
Lego it is!
Some more modifications (again rom wise)
Almost 800h per card (not giving up!)
Still 4A!!
Some more modifications (again rom wise)
Almost 800h per card
(not giving up!)Still 4A!!
Looks good, are those Chips from the GPU's soldered directly to the Pandaminer board or is it still a modular system with swappable cards ?
They're swappable
Its all lego parts.
Custom mobo with 8 mini-pcie slots and then 8 mobile rx 480s plugged in.
Some more results.
So XMR still at 4amps (880watt) after 15hrs.
Picture:
Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..)
I will test with genoil's as well later today.
236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now..
Picture:
Did a testrun for zcash as well.
1730H while consuming 4.9A (1078watt)
Picture:
Then i did some minor modifcations (rom wise)
Improved hashrate and same consumption.
So still 4A (880 watt) but this time hitting 6400h
Picture:
Again, overall, i must say, awesome machine.
This could be seriously interesting for bigger farms.
I made it so that i just plug in the power, it boots and starts mining.
Other algo, no problem. Switch and go.
Greetings!
So XMR still at 4amps (880watt) after 15hrs.
Picture:
Also did a quick testrun on ethereum using the latest available Claymore miner (bad comparison vs Windows as the latest release there is newer and faster, i tested this and it is faster..)
I will test with genoil's as well later today.
236Mh while consuming 5.3A (1166watt) most consumption i've seen as of now..
Picture:
Did a testrun for zcash as well.
1730H while consuming 4.9A (1078watt)
Picture:
Then i did some minor modifcations (rom wise)
Improved hashrate and same consumption.
So still 4A (880 watt) but this time hitting 6400h
Picture:
Again, overall, i must say, awesome machine.
This could be seriously interesting for bigger farms.
I made it so that i just plug in the power, it boots and starts mining.
Other algo, no problem. Switch and go.
Greetings!
I'm pretty sure Claymore isn't going to release anything for linux anymore. Perhaps he will, but i don't think so..
I'm running claymore's v9.3 ZEC miner on linux (ethOS), but can't speak for any of his other miners running on linux.
Edit: I just upgraded to claymore v9.3 and will check to see what flypool reports as my 24hour hash rate. Currently it reports 141.4 H/s.
It appears that they changed fans somewhere between the prototype (that used 7x or 8x Delta 60mm screamers - that ARE very good reliability) to 5x of some sort of an 80mm fan?
I've not seen any pictures that actually showed the actual fans on a production unit though.
I've not seen any pictures that actually showed the actual fans on a production unit though.
delta 80 mm they are loud but not nasty pitch they use .8 amps at 12 volt that is about 10 watts a fan
possible replacement
https://www.amazon.com/Bgears-Performance-Black-b-PWM-2Ball/dp/B00UTIB994/ref=sr_1_fkmr1_1?
also delta makes a slower fan
if this can run in a 96f garage doing 237mh for eth
commonsense means lower ambient temp would allow for lower fan speed.
I will buy a few fans use them as push.
the unit uses 9 fans
push pull over the gpus and push over the cpu.
WOW - I knew you will mod these 480M sooner or later!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
I can probably do better though..
Ha, yeah, have to admit, the panda is in a warehouse where it's around 5-10 degrees at this moment.
They're still low though, when running stock it was an average of 44 degrees, highest temp is now at 40 and lowest 31
.Will post updates as soon as i can. Busy busy..
my panda is in a 95f garage running the oem windows 10 .
I updated to the latest eth miner from claymore for windows and I am getting 237mh at 1125-1150 watts
every gpu reads 30 or 31 mh
WOW - I knew you will mod these 480M sooner or later!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
I can probably do better though..
Ha, yeah, have to admit, the panda is in a warehouse where it's around 5-10 degrees at this moment.
They're still low though, when running stock it was an average of 44 degrees, highest temp is now at 40 and lowest 31
.Will post updates as soon as i can. Busy busy..
From the pictures - looks like the fans are also good quality.
And Philip said that they don't scream like the ones in Antminers.
Well the most important thing here is that undervolting is possible and temp reporting and controls are also working in Linux.
Claymore says he is prioritizing his XMR v10 miners so I hope much improvement for RX GPU support. Hope he release Linux build for v10.
The fans seem to be indeed of decent quality. This has to be seen in the longer run.
Temp reporting isn't really correct as it has no effect. The fans of the pandaminer are directly connected to the main board.
I'm pretty sure Claymore isn't going to release anything for linux anymore. Perhaps he will, but i don't think so..
Greetings!
Fantastic stuff! Are you going to be selling a copy of your Linux build and the roms with a tutorial on how to do this on a Pandaminer? If you are I may just have to buy a Pandaminer! LOL
It appears that they changed fans somewhere between the prototype (that used 7x or 8x Delta 60mm screamers - that ARE very good reliability) to 5x of some sort of an 80mm fan?
I've not seen any pictures that actually showed the actual fans on a production unit though.
I've not seen any pictures that actually showed the actual fans on a production unit though.
WOW - I knew you will mod these 480M sooner or later!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
I can probably do better though..
Ha, yeah, have to admit, the panda is in a warehouse where it's around 5-10 degrees at this moment.
They're still low though, when running stock it was an average of 44 degrees, highest temp is now at 40 and lowest 31
.Will post updates as soon as i can. Busy busy..
From the pictures - looks like the fans are also good quality.
And Philip said that they don't scream like the ones in Antminers.
Well the most important thing here is that undervolting is possible and temp reporting and controls are also working in Linux.
Claymore says he is prioritizing his XMR v10 miners so I hope much improvement for RX GPU support. Hope he release Linux build for v10.
The fans seem to be indeed of decent quality. This has to be seen in the longer run.
Temp reporting isn't really correct as it has no effect. The fans of the pandaminer are directly connected to the main board.
I'm pretty sure Claymore isn't going to release anything for linux anymore. Perhaps he will, but i don't think so..
Greetings!
WOW - I knew you will mod these 480M sooner or later!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
I can probably do better though..
Ha, yeah, have to admit, the panda is in a warehouse where it's around 5-10 degrees at this moment.
They're still low though, when running stock it was an average of 44 degrees, highest temp is now at 40 and lowest 31
.Will post updates as soon as i can. Busy busy..
From the pictures - looks like the fans are also good quality.
And Philip said that they don't scream like the ones in Antminers.
Well the most important thing here is that undervolting is possible and temp reporting and controls are also working in Linux.
Claymore says he is prioritizing his XMR v10 miners so I hope much improvement for RX GPU support. Hope he release Linux build for v10.
WOW - I knew you will mod these 480M sooner or later!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
I can probably do better though..
Ha, yeah, have to admit, the panda is in a warehouse where it's around 5-10 degrees at this moment.
They're still low though, when running stock it was an average of 44 degrees, highest temp is now at 40 and lowest 31
.Will post updates as soon as i can. Busy busy..
WOW - I knew you will mod these 480M sooner or later!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
What sorcery .... 6200h sgminer-gm XMR at 880 watt ~ 4amps !!!
And those temps -- are you for real? Amazing!
Looks good, are those Chips from the GPU's soldered directly to the Pandaminer board or is it still a modular system with swappable cards ?
They're swappable
Looks good, are those Chips from the GPU's soldered directly to the Pandaminer board or is it still a modular system with swappable cards ?
Small update.
Modified that rom (which was already modified, aka copied straps :p)
I added some custom timings to that and added vddc offset.
Result, so far only xmr
Stock Windows (their tests)
-------------------------------
5890h using claymore so fee as well.. while consuming 1120 watt.
Mine, modified rom :Linux
-----------------------
6200h using sgminer so no fee while consuming 880 watt (4amp)
Screenshot of the miner
Yeah, was only running for 3minutes when i took it but it still going strong.
And those temps :p
here's a picture of my ampclamp
Flashing....
Will report back later!
Modified that rom (which was already modified, aka copied straps :p)
I added some custom timings to that and added vddc offset.
Result, so far only xmr
Stock Windows (their tests)
-------------------------------
5890h using claymore so fee as well.. while consuming 1120 watt.
Mine, modified rom :Linux
-----------------------
6200h using sgminer so no fee while consuming 880 watt (4amp)
Screenshot of the miner
Yeah, was only running for 3minutes when i took it but it still going strong.
And those temps :p
here's a picture of my ampclamp
Flashing....
Will report back later!
if you are in Europe - how much they write on invoice? (because high VAT...)
30 $ for Case
10 $ for Fan
Thank you for sharing your experience with Linux on Pandaminer.
How do you get into the BIOS?
Please elaborate. What difficulties did you encounter?
So you'll have to change bios settings for both of them to work.
How do you get into the BIOS?
No, linux is not a straightforward install. There are several reasons for this and you'll see when you try
Please elaborate. What difficulties did you encounter?
if you are in Europe - how much they write on invoice? (because high VAT...)
If you have a company, are from europa and own a vat number, it'll be an intra-community delivery. In other words, no tax.
Greetings
Send me a pm.
Can you please elaborate on this? What settings? In BIOS/CMOS?
Is the 2nd HDMI connector connected to the onboard system or to one of the GPU?
Is the M.2 SSD slot limited to 42mm?
Can you confirm that there's 2 RAM slots?
Is Linux a straightforward install or is there anything we need to watch out for?
I just ordered 1 PandaMiner, had I seen your thread earlier I would have ordered more to save on shipping.
I'll try to put esxi on and enable GPU passthrough so I have the flexibility of switching OS quickly.
Is the 2nd HDMI connector connected to the onboard system or to one of the GPU?
Is the M.2 SSD slot limited to 42mm?
Can you confirm that there's 2 RAM slots?
Is Linux a straightforward install or is there anything we need to watch out for?
I just ordered 1 PandaMiner, had I seen your thread earlier I would have ordered more to save on shipping.
I'll try to put esxi on and enable GPU passthrough so I have the flexibility of switching OS quickly.
Of course.
Bios settings are a big factor yes.
Both HDMI jacks are connected to the mainboard, the mainboard is some sort of a pci switch.
So you'll have to change bios settings for both of them to work.
No, linux is not a straightforward install. There are several reasons for this and you'll see when you try
if you are in Europe - how much they write on invoice? (because high VAT...)
If you have a company, are from europa and own a vat number, it'll be an intra-community delivery. In other words, no tax.
Greetings
In this Internet and Bitcoin era....
... why cant we just download the image and pay in BTC?
... saves time, save counterparty charges, supports Bitcoin and blockchain.
Haha, if everything would just be so easy..
I'll think about it.. very hard..
if you are in Europe - how much they write on invoice? (because high VAT...)
If you have a company, are from europa and own a vat number, it'll be an intra-community delivery. In other words, no tax.
Greetings
In this Internet and Bitcoin era....
... why cant we just download the image and pay in BTC?
... saves time, save counterparty charges, supports Bitcoin and blockchain.
what was wrong with the HDMI ports?
Settings were all messed up Is the 2nd HDMI connector connected to the onboard system or to one of the GPU?
Is the M.2 SSD slot limited to 42mm?
Can you confirm that there's 2 RAM slots?
Is Linux a straightforward install or is there anything we need to watch out for?
I just ordered 1 PandaMiner, had I seen your thread earlier I would have ordered more to save on shipping.
I'll try to put esxi on and enable GPU passthrough so I have the flexibility of switching OS quickly.
whats the boot up key to access BIOS?
DEL?
F12?
if you are in Europe - how much they write on invoice? (because high VAT...)
If you have a company, are from europa and own a vat number, it'll be an intra-community delivery. In other words, no tax.
Greetings
Great that you have got the Linux up and running.
Can you run some test on XMR mining with sgminer-gm and wolf XMR miner?
Claymore should be updating his Cryptonight miner soon, hope he will have Linux version by then.
Surprised that you haven't started modding the 480M yet.... maybe a 480MlowenergyOK.rom ?
Thanks - great job!
Can you run some test on XMR mining with sgminer-gm and wolf XMR miner?
Claymore should be updating his Cryptonight miner soon, hope he will have Linux version by then.
Surprised that you haven't started modding the 480M yet.... maybe a 480MlowenergyOK.rom ?
Thanks - great job!
100% that standard roms will not work with mobile ones. And in case of firing cards - the restoration will be way too complicated
Great that you have got the Linux up and running.
Can you run some test on XMR mining with sgminer-gm and wolf XMR miner?
Claymore should be updating his Cryptonight miner soon, hope he will have Linux version by then.
Surprised that you haven't started modding the 480M yet.... maybe a 480MlowenergyOK.rom ?
Thanks - great job!
Can you run some test on XMR mining with sgminer-gm and wolf XMR miner?
Claymore should be updating his Cryptonight miner soon, hope he will have Linux version by then.
Surprised that you haven't started modding the 480M yet.... maybe a 480MlowenergyOK.rom ?
Thanks - great job!
what was wrong with the HDMI ports?
Settings were all messed up Is the 2nd HDMI connector connected to the onboard system or to one of the GPU?
Is the M.2 SSD slot limited to 42mm? wrong it is a msata
Can you confirm that there's 2 RAM slots? wrong 1 slot
Is Linux a straightforward install or is there anything we need to watch out for?
I just ordered 1 PandaMiner, had I seen your thread earlier I would have ordered more to save on shipping.
I'll try to put esxi on and enable GPU passthrough so I have the flexibility of switching OS quickly.
photos of the msata and ram are posted on my review thread.
https://bitcointalksearch.org/topic/m.17366877
but op is the man as a working linux is gold and he can lower fan speeds as the fans can do 70% (a guess by me).
he mentions he can lower fan speed and that his gpus are only 40c.
this machine will be even better then hoped for. if fans run at 60% and temps are 55c for the gpus.
what was wrong with the HDMI ports?
Settings were all messed up Is the 2nd HDMI connector connected to the onboard system or to one of the GPU?
Is the M.2 SSD slot limited to 42mm?
Can you confirm that there's 2 RAM slots?
Is Linux a straightforward install or is there anything we need to watch out for?
I just ordered 1 PandaMiner, had I seen your thread earlier I would have ordered more to save on shipping.
I'll try to put esxi on and enable GPU passthrough so I have the flexibility of switching OS quickly.
if you are in Europe - how much they write on invoice? (because high VAT...)
If you have a company, are from europa and own a vat number, it'll be an intra-community delivery. In other words, no tax.
Greetings
if you are in Europe - how much they write on invoice? (because high VAT...)
what was wrong with the HDMI ports?
Settings were all messed up can you access BIOS?
Yes i can.can plug a Linux boot thumb drive from USB?
Yes i can I have a new hero!
I put your thread link here
https://bitcointalk.org/index.php?topic=1584973.new#new
Cheers!I put your thread link here
https://bitcointalk.org/index.php?topic=1584973.new#new
I need a copy of that software
My windows build does not show temps or fan speeds. his linux does
at op I am doing around 1730h and 1062 watts with an evga 1600 g2 psu. and around 1200 watt with their stock gpu.
how much watts are you using for your 1696h?
The fans are full speed and may be able to drop to 70% which would really be good.
The unit has 9 fans at 10 watts each. That comes to 90 watts since fans are full speed.
Lowering of the fans could save 30 watts.
I have no idea about the consumption right now. I will have more detailed info tomorrow.My windows build does not show temps or fan speeds. his linux does
at op I am doing around 1730h and 1062 watts with an evga 1600 g2 psu. and around 1200 watt with their stock gpu.
how much watts are you using for your 1696h?
The fans are full speed and may be able to drop to 70% which would really be good.
The unit has 9 fans at 10 watts each. That comes to 90 watts since fans are full speed.
Lowering of the fans could save 30 watts.
Yes they are set at 100%, i can lower them though.. Temperature of the gpu's is around 40 degrees average at this moment.
greetings!
nice project - sure better then chinese Win10
I need a copy of that software
My windows build does not show temps or fan speeds. his linux does
at op I am doing around 1730h and 1062 watts with an evga 1600 g2 psu. and around 1200 watt with their stock gpu.
how much watts are you using for your 1696h?
The fans are full speed and may be able to drop to 70% which would really be good.
The unit has 9 fans at 10 watts each. That comes to 90 watts since fans are full speed.
Lowering of the fans could save 30 watts.
nice project - sure better then chinese Win10
Hey guys!
As i've mentioned earlier, i also ordered a pandaminer.
It arrived today! Yey.
I took the time to boot the original ssd into that awesome Chinese Windows 10 and it took me around 10 minutes to turn it off again and to replace that ssd with a new one.
Of course i played around with it and installed linux on it (ps. i also fixed both the hdmi outputs, both are working fine now)
Here are some pictures.
Will post power / speed results later. Will also fetch that rom and modify the hell out of it.. "later.. :p"
If this runs smooth for more than 2 days, i will consider making this commercial, i mean: the pandaminer modified with modified roms. (only europe "for now")..
Pictures: (i'm just posting the links because i hate the fact that pictures will make me have to scroll like a madman to get to the bottom of the page..)
They box :p
Box
Messed around with it and running on linux
Linux
More info coming later!
Greetings!
As i've mentioned earlier, i also ordered a pandaminer.
It arrived today! Yey.
I took the time to boot the original ssd into that awesome Chinese Windows 10 and it took me around 10 minutes to turn it off again and to replace that ssd with a new one.
Of course i played around with it and installed linux on it
(ps. i also fixed both the hdmi outputs, both are working fine now)Here are some pictures.
Will post power / speed results later. Will also fetch that rom and modify the hell out of it.. "later.. :p"
If this runs smooth for more than 2 days, i will consider making this commercial, i mean: the pandaminer modified with modified roms. (only europe "for now")..
Pictures: (i'm just posting the links because i hate the fact that pictures will make me have to scroll like a madman to get to the bottom of the page..)
They box :p
Box
Messed around with it and running on linux
Linux
More info coming later!
Greetings!
I have a new hero!
I put your thread link here
https://bitcointalk.org/index.php?topic=1584973.new#new
what was wrong with the HDMI ports?
can you access BIOS?
can plug a Linux boot thumb drive from USB?
can you access BIOS?
can plug a Linux boot thumb drive from USB?
Edit: For updates and more info -> Here and scroll down..
Hey guys!
As i've mentioned earlier, i also ordered a pandaminer.
It arrived today! Yey.
I took the time to boot the original ssd into that awesome Chinese Windows 10 and it took me around 10 minutes to turn it off again and to replace that ssd with a new one.
Of course i played around with it and installed linux on it (ps. i also fixed both the hdmi outputs, both are working fine now)
Here are some pictures.
Will post power / speed results later. Will also fetch that rom and modify the hell out of it.. "later.. :p"
If this runs smooth for more than 2 days, i will consider making this commercial, i mean: the pandaminer modified with modified roms. (only europe "for now")..
Pictures: (i'm just posting the links because i hate the fact that pictures will make me have to scroll like a madman to get to the bottom of the page..)
They box :p
Box
Messed around with it and running on linux
Linux
More info coming later!
Greetings!
Hey guys!
As i've mentioned earlier, i also ordered a pandaminer.
It arrived today! Yey.
I took the time to boot the original ssd into that awesome Chinese Windows 10 and it took me around 10 minutes to turn it off again and to replace that ssd with a new one.
Of course i played around with it and installed linux on it
(ps. i also fixed both the hdmi outputs, both are working fine now)Here are some pictures.
Will post power / speed results later. Will also fetch that rom and modify the hell out of it.. "later.. :p"
If this runs smooth for more than 2 days, i will consider making this commercial, i mean: the pandaminer modified with modified roms. (only europe "for now")..
Pictures: (i'm just posting the links because i hate the fact that pictures will make me have to scroll like a madman to get to the bottom of the page..)
They box :p
Box
Messed around with it and running on linux
Linux
More info coming later!
Greetings!
Jump to: