Topic: Problem with innosillicon T2TH+ 37TH (Read 214 times)

Can you try to flash the miner first you can find the firmware of this miner from innosilicon support below?

- https://www.innosilicon.com/html/support_en/download.html

It might be a program issue since they didn't test it yet above you can try it first before you touch any hardware from your miner.
And then update here if there different results on the log(So make sure to get a copy of your logs before and after firmware flashed.).

Hello,

Did you fixed de problem? I have the same problem Help me

Yeah looks like a dead board.  There are some repair guys that may help are you usa?

this guy has fixed some t1 gear which was made by innosilicon.  as a side note   t1 t2 t3 all made by innosilicon

https://bitcointalksearch.org/topic/fixing-dragonmint-t1-miners-thoughts-and-observations-5225659

you could pm him  see what he says.

I will try...
Now I'm running back at perf-. It's ok with 2 hashboards, its showing and running good.
I've tried on factory mod (I was running for a week on this mod) but no signal of chain1 now.

---

Other modes the hashboard does not work. I've tested with only this hashboard connected, and the miner do not start mining. Just to remember, the others two works well.


This log with reset failed still here.

Shut it off   wait ten min do every mode from

bal--
Bal-
Bal
Bal+
Bal++
factory--
factory-
factory
factory+

if none work all three boards

try one other pool if no go   board may be toast.

what did you used to run it at?

I've tried 3 or 4 modes... no one is working for chain 1. I was running on perf- yesterday and today, it was OK. Then one hash board disappeared.

those miners have a lot of speed settings.

eco             balance           factory     performance

and in between settings

eco

eco+
eco++
bal--
bal-

Bal

bal+
bal++
factory--
factory-

factory

factory+
factory++

proformance

what are you set to?

if you are on factory drop it to bal+

play with the settings  there are about 13-15 of them   you may get one or more setting to make all 3 boards work.

Today I drove from Howell, NJ to Clifton, NJ    and back about 65 miles each way.

I went to my farm and worked on gear.  I left at 6am and drove on an empty highway speed limit is 65 miles an hour I drove 75-80

My Kia Forte can do about 100 miles an hour on a slight down hill straight empty road.  I know I did it once for about 2-3 minutes.

Every time I get a new car I go to a spot where it is easy enough to get you car to max out.

My kia forte is not safe at 100 miles an hour I can feel it lose some grip in the 95-100
speed..

So I do what it can on an empty road 78-82 feels pretty good it ia my second kia forte I have owen them for about 8 years
I had a blow out on an empty highway at 75 and was able to safely spot the car.

See where I am going here.
Try to back your gear off  a few notches it may not like the speed you are doing with it.

I have 3 inno's

t2t24    likes bal bal+ or Bal++
t3t39    Like factory -
t23t50  likes factory +

Hi,

One hashboard doesn't showing anymore in miner status. In this case, I found "error 24" that's mean some problem with hashboard.

Here the log:


Well, the problem is with chain1, it's always shows reset failed many times, after these tries, miner turn off the chain1 and go on with others chains. **The chain 0 and 2 is running OK in all modes. So, the hashboard (chain1) is dead?