Topic: Problems with the boards after burning a fan! (Read 149 times)

I actually run up to 575! The auto-tune chooses the best voltages for each card and then I reduce it from 575 until I leave each chip with few errors! I try never to miss 0.1%!
 I tried to buy these at 7500rpm, because it's been 40 degrees and what actually spoils our machines are the temperatures and humidity, it's not what we pull for it! They always told me that!
 I live in Europe and the boards around here are crazy...I bought the L3+ for 390e and people are now selling each board for 300e!
 I tried using a method that results in a T15 that I have! I cleaned the board with isopropyl alcohol, then I used wd-40 electrical contact cleaner and finally I am moving the frequencies and it is recovering! In this one I already result in two of the boards! Just this third... It might just be luck, but I was left thinking it might be some software error that could lead to a hardware error! Also because in the Kernel it continues to appear "local0.err cgminer[5120]: Get [1]Temp Data Failed!"

What did you run at?

freq 384 or lower?

freq 400 or higher?


are you usa based?


my thoughts are

like the words from an old rock and rock song.

“Nah Nah Na Na say hey goodby.”

looks like you fried it all.

but the hope would be that a proper fan and not a crazy stupid burn the controller board could help.

So detach the 7500 rpm monster over kill fan and stop taxing the controller.

find a proper fan and try again.

good luck as you will need it.


you could look in the marketplace here and see if anyone is selling L3+ gear.

hint some one is.

he is a usa based seller.

it is me.

I also am selling working L3+ boards.

and I could toss in a proper fan.

Its my Kernal

Jul 18 14:53:53 (none) local0.notice cgminer: Entering probe_pools_inst
Jul 18 14:53:54 (none) local0.notice cgminer: Pool 3 is alive, going further
Jul 18 14:53:54 (none) local0.notice cgminer: Probe pools done
Jul 18 14:53:54 (none) local0.notice cgminer[3689]:  detected at /sys/class/gpio/gpio51/value  chain 0
Jul 18 14:53:54 (none) local0.notice cgminer[3689]:  detected at /sys/class/gpio/gpio48/value  chain 1
Jul 18 14:53:54 (none) local0.notice cgminer[3689]:  detected at /sys/class/gpio/gpio47/value  chain 2
Jul 18 14:53:54 (none) local0.notice cgminer[3689]:  detected at /sys/class/gpio/gpio44/value  chain 3
Jul 18 14:53:54 (none) local0.notice cgminer[3689]: detect total chain num 4
Jul 18 14:53:54 (none) local0.notice cgminer[3689]: i2c init ok
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: in tty_init
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: tty_init 0
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: Start A New Asic Response.Chain Id:[0]
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: tty_init 1
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: Start A New Asic Response.Chain Id:[1]
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: tty_init 2
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: Start A New Asic Response.Chain Id:[2]
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: tty_init 3
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: Start A New Asic Response.Chain Id:[3]
Jul 18 14:54:04 (none) local0.notice cgminer[3689]: open device over
Jul 18 14:54:05 (none) local0.notice cgminer[3689]: chain[0] set voltage = 1381.503211  real:125 mv
Jul 18 14:54:05 (none) local0.notice cgminer[3689]: chain[1] set voltage = 1381.503211  real:125 mv
Jul 18 14:54:05 (none) local0.notice cgminer[3689]: chain[2] set voltage = 1381.503211  real:125 mv
Jul 18 14:54:05 (none) local0.notice cgminer[3689]: chain[3] set voltage = 1381.503211  real:125 mv
Jul 18 14:54:06 (none) local0.notice cgminer[3689]: send cmd to get chip address
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 31 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 36 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 40 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 44 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 63 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 87 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 100 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 108 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 118 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859800
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 123 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg,crc5 error,should be 00,but check as 10 133 182
Jul 18 14:54:06 (none) local0.err cgminer[3689]: bitmain_scanreg: reg_value = 0x14859c00
Jul 18 14:54:08 (none) local0.notice cgminer[3689]: Chain 0 ASIC 21 !!!
Jul 18 14:54:08 (none) local0.notice cgminer[3689]: Chain 1 ASIC 17 !!!
Jul 18 14:54:08 (none) local0.notice cgminer[3689]: Chain 2 ASIC 72 !!!
Jul 18 14:54:08 (none) local0.notice cgminer[3689]: Chain 3 ASIC 72 !!!
Jul 18 14:54:08 (none) local0.notice cgminer[3689]: Need to recheck asic num !!!
...
Jul 18 14:54:26 (none) local0.err cgminer[4043]: bitmain_scanreg: reg_value = 0x14859800
Jul 18 14:54:28 (none) local0.notice cgminer[4043]: Chain 0 ASIC 21 !!!
Jul 18 14:54:28 (none) local0.notice cgminer[4043]: Chain 1 ASIC 41 !!!
Jul 18 14:54:28 (none) local0.notice cgminer[4043]: Chain 2 ASIC 72 !!!
Jul 18 14:54:28 (none) local0.notice cgminer[4043]: Chain 3 ASIC 72 !!!
Jul 18 14:54:28 (none) local0.notice cgminer[4043]: Need to recheck asic num !!!
...
Jul 18 14:54:30 (none) local0.notice cgminer[4043]: Chain 0 ASIC 21 !!!
Jul 18 14:54:30 (none) local0.notice cgminer[4043]: Chain 1 ASIC 44 !!!
Jul 18 14:54:30 (none) local0.notice cgminer[4043]: Chain 2 ASIC 72 !!!
Jul 18 14:54:30 (none) local0.notice cgminer[4043]: Chain 3 ASIC 72 !!!
Jul 18 14:54:30 (none) local0.notice cgminer[4043]: Need to recheck asic num !!!
...
Jul 18 14:54:32 (none) local0.notice cgminer[4043]: Chain 0 ASIC 21 !!!
Jul 18 14:54:32 (none) local0.notice cgminer[4043]: Chain 1 ASIC 40 !!!
Jul 18 14:54:32 (none) local0.notice cgminer[4043]: Chain 2 ASIC 72 !!!
Jul 18 14:54:32 (none) local0.notice cgminer[4043]: Chain 3 ASIC 72 !!!
Jul 18 14:54:32 (none) local0.notice cgminer[4043]: addrInterval = '3'
Jul 18 14:54:32 (none) local0.notice cgminer[4043]: software_set_address: chain 0 has 21 ASIC, and addrInterval is 3
Jul 18 14:54:32 (none) local0.notice cgminer[4043]: Now Set

• Chain Address

Jul 18 14:54:33 (none) local0.notice cgminer[4043]: software_set_address: chain 1 has 40 ASIC, and addrInterval is 3
Jul 18 14:54:33 (none) local0.notice cgminer[4043]: Now Set [1] Chain Address
Jul 18 14:54:34 (none) local0.notice cgminer[4043]: software_set_address: chain 2 has 72 ASIC, and addrInterval is 3
Jul 18 14:54:34 (none) local0.notice cgminer[4043]: Now Set [2] Chain Address
Jul 18 14:54:35 (none) local0.notice cgminer[4043]: software_set_address: chain 3 has 72 ASIC, and addrInterval is 3
Jul 18 14:54:35 (none) local0.notice cgminer[4043]: Now Set [3] Chain Address
Jul 18 14:54:36 (none) local0.notice cgminer[4043]: Set freq 384 on chain 0
...
ul 18 14:54:37 (none) local0.notice cgminer[4043]: Set freq 384 on chain 1
Jul 18 14:54:37 (none) local0.notice cgminer[4043]: Set freq 512 on chain 2
Jul 18 14:54:38 (none) local0.notice cgminer[4043]: Set freq 512 on chain 3
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: bitmain_L3_init: fan_eft : 0  fan_pwm : 30
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: chain 0, frequency = '384'
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: chain 0, dev.timeout = 19
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: chain 1, frequency = '384'
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: chain 1, dev.timeout = 19
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: chain 2, frequency = '509'
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: chain 2, dev.timeout = 14
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: chain 3, frequency = '511'
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: chain 3, dev.timeout = 14
Jul 18 14:54:39 (none) local0.notice cgminer[4043]: opt_bitmain_L3_core_temp : 2
...
Jul 18 14:54:40 (none) local0.err cgminer[4043]: Get [1]Temp Data Failed!
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg,crc5 error,should be 04,but check as 09 1 4
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg: reg_value = 0x0198011b
Jul 18 14:54:41 (none) local0.notice cgminer[4043]: Chain 2 chip 0 RemoteTemp 0x0
Jul 18 14:54:41 (none) local0.notice cgminer[4043]: Chain 3 chip 0 RemoteTemp 0x0
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg,crc5 error,should be 00,but check as 1d 0 6
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg: reg_value = 0x01980100
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg,crc5 error,should be 00,but check as 1a 3 6
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg: reg_value = 0x41980100
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg,crc5 error,should be 00,but check as 1a 0 6
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg: reg_value = 0x41980100
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg,crc5 error,should be 00,but check as 1a 3 6
Jul 18 14:54:41 (none) local0.err cgminer[4043]: bitmain_scanreg: reg_value = 0x41980100
Jul 18 14:54:41 (none) local0.notice cgminer[4043]: Remote = 0 Chain 2 chip 0 local 0x20 remote 0x0 offset 0xffffffd8
Jul 18 14:54:41 (none) local0.notice cgminer[4043]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0xffffffd8
Jul 18 14:54:41 (none) local0.notice cgminer[4043]: Remote = 0 Chain 3 chip 0 local 0x1f remote 0x0 offset 0xffffffd8
Jul 18 14:54:41 (none) local0.notice cgminer[4043]: Remote = 0 Chain 3 chip 1 local 0x0 remote 0x0 offset 0xffffffd8
...
Jul 18 14:55:15 (none) local0.notice cgminer[4641]: send cmd to get chip address
Jul 18 14:55:17 (none) local0.notice cgminer[4641]: Chain 0 ASIC 21 !!!
Jul 18 14:55:17 (none) local0.notice cgminer[4641]: Chain 1 ASIC 72 !!!
Jul 18 14:55:17 (none) local0.notice cgminer[4641]: Chain 2 ASIC 72 !!!
Jul 18 14:55:17 (none) local0.notice cgminer[4641]: Chain 3 ASIC 72 !!!
Jul 18 14:55:17 (none) local0.notice cgminer[4641]: Need to recheck asic num !!!
Jul 18 14:55:35 (none) local0.err cgminer: Miner compile time: Thu Feb 18 14:03:24 UTC 2021 type: Antminer L3+ Hiveon
Jul 18 14:55:35 (none) local0.warn cgminer: Started cgminer 4.9.0 rwglr
Jul 18 14:55:35 (none) local0.notice cgminer: Entering probe_pools_inst
Jul 18 14:55:36 (none) local0.notice cgminer: Pool 3 is alive, going further
Jul 18 14:55:36 (none) local0.notice cgminer: Probe pools done
Jul 18 14:55:36 (none) local0.notice cgminer[5120]:  detected at /sys/class/gpio/gpio51/value  chain 0
Jul 18 14:55:36 (none) local0.notice cgminer[5120]:  detected at /sys/class/gpio/gpio48/value  chain 1
Jul 18 14:55:36 (none) local0.notice cgminer[5120]:  detected at /sys/class/gpio/gpio47/value  chain 2
Jul 18 14:55:36 (none) local0.notice cgminer[5120]:  detected at /sys/class/gpio/gpio44/value  chain 3
Jul 18 14:55:36 (none) local0.notice cgminer[5120]: detect total chain num 4
Jul 18 14:55:36 (none) local0.notice cgminer[5120]: i2c init ok
Jul 18 14:55:45 (none) local0.notice cgminer[5120]: in tty_init
Jul 18 14:55:45 (none) local0.notice cgminer[5120]: tty_init 0
Jul 18 14:55:45 (none) local0.notice cgminer[5120]: Start A New Asic Response.Chain Id:[0]
Jul 18 14:55:45 (none) local0.notice cgminer[5120]: tty_init 1
Jul 18 14:55:45 (none) local0.notice cgminer[5120]: Start A New Asic Response.Chain Id:[1]
Jul 18 14:55:46 (none) local0.notice cgminer[5120]: tty_init 2
Jul 18 14:55:46 (none) local0.notice cgminer[5120]: Start A New Asic Response.Chain Id:[2]
Jul 18 14:55:46 (none) local0.notice cgminer[5120]: tty_init 3
Jul 18 14:55:46 (none) local0.notice cgminer[5120]: Start A New Asic Response.Chain Id:[3]
Jul 18 14:55:46 (none) local0.notice cgminer[5120]: open device over
Jul 18 14:55:46 (none) local0.notice cgminer[5120]: chain[0] set voltage = 1381.503211  real:125 mv
Jul 18 14:55:46 (none) local0.notice cgminer[5120]: chain[1] set voltage = 1381.503211  real:125 mv
Jul 18 14:55:46 (none) local0.notice cgminer[5120]: chain[2] set voltage = 1381.503211  real:125 mv
Jul 18 14:55:47 (none) local0.notice cgminer[5120]: chain[3] set voltage = 1381.503211  real:125 mv
Jul 18 14:55:47 (none) local0.notice cgminer[5120]: send cmd to get chip address
Jul 18 14:55:49 (none) local0.notice cgminer[5120]: Chain 0 ASIC 21 !!!
Jul 18 14:55:49 (none) local0.notice cgminer[5120]: Chain 1 ASIC 72 !!!
Jul 18 14:55:49 (none) local0.notice cgminer[5120]: Chain 2 ASIC 72 !!!
Jul 18 14:55:49 (none) local0.notice cgminer[5120]: Chain 3 ASIC 72 !!!
Jul 18 14:55:49 (none) local0.notice cgminer[5120]: Need to recheck asic num !!!
Jul 18 14:55:51 (none) local0.notice cgminer[5120]: Chain 0 ASIC 21 !!!
Jul 18 14:55:51 (none) local0.notice cgminer[5120]: Chain 1 ASIC 72 !!!
Jul 18 14:55:51 (none) local0.notice cgminer[5120]: Chain 2 ASIC 72 !!!
Jul 18 14:55:51 (none) local0.notice cgminer[5120]: Chain 3 ASIC 72 !!!
Jul 18 14:55:51 (none) local0.notice cgminer[5120]: Need to recheck asic num !!!
Jul 18 14:55:53 (none) local0.notice cgminer[5120]: Chain 0 ASIC 21 !!!
Jul 18 14:55:53 (none) local0.notice cgminer[5120]: Chain 1 ASIC 72 !!!
Jul 18 14:55:53 (none) local0.notice cgminer[5120]: Chain 2 ASIC 72 !!!
Jul 18 14:55:53 (none) local0.notice cgminer[5120]: Chain 3 ASIC 72 !!!
Jul 18 14:55:53 (none) local0.notice cgminer[5120]: Need to recheck asic num !!!
Jul 18 14:55:55 (none) local0.notice cgminer[5120]: Chain 0 ASIC 21 !!!
Jul 18 14:55:55 (none) local0.notice cgminer[5120]: Chain 1 ASIC 72 !!!
Jul 18 14:55:55 (none) local0.notice cgminer[5120]: Chain 2 ASIC 72 !!!
Jul 18 14:55:55 (none) local0.notice cgminer[5120]: Chain 3 ASIC 72 !!!
Jul 18 14:55:55 (none) local0.notice cgminer[5120]: Need to recheck asic num !!!
Jul 18 14:55:58 (none) local0.notice cgminer[5120]: Chain 0 ASIC 21 !!!
Jul 18 14:55:58 (none) local0.notice cgminer[5120]: Chain 1 ASIC 72 !!!
Jul 18 14:55:58 (none) local0.notice cgminer[5120]: Chain 2 ASIC 72 !!!
Jul 18 14:55:58 (none) local0.notice cgminer[5120]: Chain 3 ASIC 72 !!!
Jul 18 14:55:58 (none) local0.notice cgminer[5120]: Need to recheck asic num !!!
Jul 18 14:56:00 (none) local0.notice cgminer[5120]: Chain 0 ASIC 21 !!!
Jul 18 14:56:00 (none) local0.notice cgminer[5120]: Chain 1 ASIC 72 !!!
Jul 18 14:56:00 (none) local0.notice cgminer[5120]: Chain 2 ASIC 72 !!!
Jul 18 14:56:00 (none) local0.notice cgminer[5120]: Chain 3 ASIC 72 !!!
Jul 18 14:56:00 (none) local0.notice cgminer[5120]: addrInterval = '3'
Jul 18 14:56:00 (none) local0.notice cgminer[5120]: software_set_address: chain 0 has 21 ASIC, and addrInterval is 3
Jul 18 14:56:00 (none) local0.notice cgminer[5120]: Now Set

• Chain Address

Jul 18 14:56:01 (none) local0.notice cgminer[5120]: software_set_address: chain 1 has 72 ASIC, and addrInterval is 3
Jul 18 14:56:01 (none) local0.notice cgminer[5120]: Now Set [1] Chain Address
Jul 18 14:56:02 (none) local0.notice cgminer[5120]: software_set_address: chain 2 has 72 ASIC, and addrInterval is 3
Jul 18 14:56:02 (none) local0.notice cgminer[5120]: Now Set [2] Chain Address
Jul 18 14:56:03 (none) local0.notice cgminer[5120]: software_set_address: chain 3 has 72 ASIC, and addrInterval is 3
Jul 18 14:56:03 (none) local0.notice cgminer[5120]: Now Set [3] Chain Address
Jul 18 14:56:04 (none) local0.notice cgminer[5120]: Set freq 512 on chain 0
Jul 18 14:56:04 (none) local0.notice cgminer[5120]: Set freq 512 on chain 1
Jul 18 14:56:05 (none) local0.notice cgminer[5120]: Set freq 512 on chain 2
Jul 18 14:56:06 (none) local0.notice cgminer[5120]: Set freq 512 on chain 3
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: bitmain_L3_init: fan_eft : 0  fan_pwm : 30
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: chain 0, frequency = '512'
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: chain 0, dev.timeout = 14
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: chain 1, frequency = '512'
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: chain 1, dev.timeout = 14
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: chain 2, frequency = '512'
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: chain 2, dev.timeout = 14
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: chain 3, frequency = '512'
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: chain 3, dev.timeout = 14
Jul 18 14:56:07 (none) local0.notice cgminer[5120]: opt_bitmain_L3_core_temp : 2
Jul 18 14:56:08 (none) local0.err cgminer[5120]: Get [1]Temp Data Failed!
Jul 18 14:56:09 (none) local0.notice cgminer[5120]: Chain 1 chip 0 RemoteTemp 0x0
Jul 18 14:56:09 (none) local0.notice cgminer[5120]: Chain 2 chip 0 RemoteTemp 0x0
Jul 18 14:56:09 (none) local0.notice cgminer[5120]: Chain 3 chip 0 RemoteTemp 0x0
Jul 18 14:56:09 (none) local0.notice cgminer[5120]: Remote = 0 Chain 1 chip 0 local 0x19 remote 0x0 offset 0xffffffd8
Jul 18 14:56:09 (none) local0.notice cgminer[5120]: Remote = 0 Chain 1 chip 1 local 0x0 remote 0x0 offset 0xffffffd8
Jul 18 14:56:09 (none) local0.notice cgminer[5120]: Remote = 0 Chain 2 chip 0 local 0x1a remote 0x0 offset 0xffffffd8
Jul 18 14:56:09 (none) local0.notice cgminer[5120]: Remote = 0 Chain 2 chip 1 local 0x0 remote 0x0 offset 0xffffffd8
Jul 18 14:56:09 (none) local0.notice cgminer[5120]: Remote = 0 Chain 3 chip 0 local 0x19 remote 0x0 offset 0xffffffd8
Jul 18 14:56:09 (none) local0.notice cgminer[5120]: Remote = 0 Chain 3 chip 1 local 0x0 remote 0x0 offset 0xffffffd8
Jul 18 14:56:11 (none) local0.err cgminer[5120]: Get [1]Temp Data Failed!
Jul 18 14:56:11 (none) local0.notice cgminer[5120]: Chain 1 chip 0 RemoteTemp 0x14
Jul 18 14:56:11 (none) local0.notice cgminer[5120]: Chain 2 chip 0 RemoteTemp 0x15
Jul 18 14:56:11 (none) local0.notice cgminer[5120]: Chain 3 chip 0 RemoteTemp 0x15

I got the warning email around 5am! But I woke up around 9am! The L3+ was in protection mode because of a missing fan! when I turned it on there was only one sign. After several attempts, the others started to appear! I still started again today and another 30 chips appeared, but they disappeared again after an hour. Couldn't this type of error be some way of protecting the board itself because of the temperature? And if it was a burnt chip, shouldn't the "X" appear?

How long did it hash before shutting down with no fans?
Cant see photo as it errors CDN error.   But you can kill hash boards with high heat.

Hello my friends! Tonight one of my L3+ fans burns out! When I woke up I replaced it with a 7500rpm one (because it was the only one I had)! The thing is, when I turned it back on, the L3 doesn't appreciate any cards! After many attempts I managed to leave the machine in the state in which the photos appear! Does anyone know what it might be? I've already tested all the cables, I've tested the board one by one, I've already cleaned the flies, mosquitoes and quotations that were inside the machine! You already washed the plates with isopropyl alcohol!

I've shared the images on reddit for you to see as I don't know how to do it here! thanks

https://www.reddit.com/r/litecoinmining/comments/om8290/board_problems_after_burning_a_fan/?utm_source=share&utm_medium=ios_app&utm_name=iossmf