PSU HP-DPS-800GB-A Help with circuit short between + & -

danilom

member

Activity: 92

Merit: 10

hi,

I tryed without screw... and green LED ON.

Welding the wire on the PCB directly

So im going to connect 2 Antminer S3 (8 pci-e molex connector)

After that, if everything OK i upload some pictures, so we can search it in the forum later

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

Quote from: RichBC on November 05, 2015, 09:05:14 AM

Quote from: danilom on November 05, 2015, 08:43:34 AM

Thanks for the replys.

Inner layers really dont know... also because others pals are running the PSU using screws throught the PCB..

But, im going to try, using another coin of screw.. and then post again

Thanks all!!

They may just have been lucky, dependant on exactly where the holes were drilled, size of the hole & size of the screws etc? What you have said though is that with the screw out there is no short & with the screw in there is a short. So either there is a problem with your cables or with the screws. Have you tried with just the screws & no cables?

Rich

also nylon screws

http://www.amazon.com/Hillman-Group-59483-10-24-4-Inch/dp/B00NQQZWYE/ref=sr_1_2?ie=UTF8&qid=1446732525&sr=8-2&keywords=nylon+screws+10-24

if the bolts you used are shorting inside the holes the nylon screws should not.

RichBC

hero member

Activity: 588

Merit: 500

Quote from: danilom on November 05, 2015, 08:43:34 AM

Thanks for the replys.

Inner layers really dont know... also because others pals are running the PSU using screws throught the PCB..

But, im going to try, using another coin of screw.. and then post again

Thanks all!!

They may just have been lucky, dependant on exactly where the holes were drilled, size of the hole & size of the screws etc? What you have said though is that with the screw out there is no short & with the screw in there is a short. So either there is a problem with your cables or with the screws. Have you tried with just the screws & no cables?

Rich

danilom

member

Activity: 92

Merit: 10

Thanks for the replys.

Inner layers really dont know... also because others pals are running the PSU using screws throught the PCB..

But, im going to try, using another coin of screw.. and then post again

Thanks all!!

RichBC

hero member

Activity: 588

Merit: 500

I think you may find that there are tracks running on some inner layers of the PCB that you cannot see. So when the screws are in you are creating a short from those inner tracks and the + & - Connections. If I am right you are lucky that the PSU is still working even with the screws removed.

If you have a multimeter make some resistance measurements and confirm what I have said. Most people either use a proper breakout board or just solder directly to the + & - edge connections.

Rich

philipma1957

legendary

Activity: 4256

Merit: 8551

'The right to privacy matters'

Quote from: danilom on November 05, 2015, 07:04:46 AM

Hi folks,

I need some help with the DIY home adapter for HP server DPS 800GB A PSU

I look at the diagram located here and internet, and made the short between pin 32 and 33, like pictures i attached. And i made holes in the + and - sections to put a screw and cables with Pci-e conectors.

If i turn on the PSU without cables it goes well, green led turn on and 12v is in the + and - pins

But seems like when i put the screw and the cables, that it make like circuit short, so i take the tester and put the tester cables in +and -, and when the screw is on it, it sounds, like cont. is in it...

I tried with 2 differente PSU new brand, to discard and the same thing, something im doing wrong...

Any idea?

attach 1 nut on the positive attach 1 nut on the neg

no cable,

turn it on if it runs:

take 1 pcie you built and attach it.

attach the nuts that are furthest apart

pos pos neg neg

danilom

member

Activity: 92

Merit: 10

Hi folks,

I need some help with the DIY home adapter for HP server DPS 800GB A PSU

I look at the diagram located here and internet, and made the short between pin 32 and 33, like pictures i attached. And i made holes in the + and - sections to put a screw and cables with Pci-e conectors.

If i turn on the PSU without cables it goes well, green led turn on and 12v is in the + and - pins

But seems like when i put the screw and the cables, that it make like circuit short, so i take the tester and put the tester cables in +and -, and when the screw is on it, it sounds, like cont. is in it...

I tried with 2 differente PSU new brand, to discard and the same thing, something im doing wrong...

Any idea?

Topic: PSU HP-DPS-800GB-A Help with circuit short between + & - (Read 1273 times)