R9 does not support pcie 1X.
It requires "PCI Express x16" slot.
It requires "PCI Express x16" slot.
That is an outright lie. I run numerous R9-380's on 6 GPU Rigs. Speaking from experience not my a$$
Topic: r9 nano (Read 937 times)
nah i think its motherboard z97 , ill go on pro btc i try it with usb risers
I use 6x nano on a H81 Pro BTC board, also got one with the B95 Anniversary board.
Works perfectly on those x1 slots.
I "had" a few furies as well, also with risers, also connected with risers to a x1 slot (MSI z97 Gaming 5 Board).
Dunno where all you guys find all those issues :p
Riser perhaps?
Works perfectly on those x1 slots.
I "had" a few furies as well, also with risers, also connected with risers to a x1 slot (MSI z97 Gaming 5 Board).
Dunno where all you guys find all those issues :p
Riser perhaps?
what mobo , and riser ? can u make pic pls ?
R9 does not support pcie 1X.
It requires "PCI Express x16" slot.
It requires "PCI Express x16" slot.
Not true. I use the nano on the x1 slot without problem. For some motherboarads, you need to short the card presence pin.
only one , im planning to buy sec card , so tried to make place for second , ill try today with other riser s mby usb will work
p45 - r7 on riser 1xpci e works
p45 - r9 nano on riser 1x pcie doesnt work
z97 anniversary- r7 on 1x doesnt work
z97- r9 nano on 1x doesnt work
z97- r9 nano 16x works
p45 - r9 nano on riser 1x pcie doesnt work
z97 anniversary- r7 on 1x doesnt work
z97- r9 nano on 1x doesnt work
z97- r9 nano 16x works
Do you have more than one riser? One of them is bad.
- the riser on the P45 with the 240 works
- the riser on the P45 with the nano doesn't work
- the riser on the Z97 doesn't work with either card
- the nano works on the Z97 works without a riser
p45 - r7 on riser 1xpci e works
p45 - r9 nano on riser 1x pcie doesnt work
z97 anniversary- r7 on 1x doesnt work
z97- r9 nano on 1x doesnt work
z97- r9 nano 16x works
p45 - r9 nano on riser 1x pcie doesnt work
z97 anniversary- r7 on 1x doesnt work
z97- r9 nano on 1x doesnt work
z97- r9 nano 16x works
mobo is z97 anniversary , i have tried on old p45 to jump it from 16x to 1x and it works fine with R7 240 but again R9 nano p45 doesnt see , and z97 doesnt see nothin (r9 nano and r7 240 )
The nano is new so it might need newer drivers. If the 240 doesn't work in the x16 slot without the riser it might
be a bad mobo. If it does work it's probably a bad riser.
mobo is z97 anniversary , i have tried on old p45 to jump it from 16x to 1x and it works fine with R7 240 but again R9 nano p45 doesnt see , and z97 doesnt see nothin (r9 nano and r7 240 )
why motherboard doesnt see my card on pcie 1X ? used standard ribbon raiser
Make sure you use a powered riser and check to see if you need to short out two
pins in the x1 slot to allow high power. Google it.
R9 does not support pcie 1X.
It requires "PCI Express x16" slot.
It requires "PCI Express x16" slot.
it's the motherboard then, what motherboard are you using?
i know for certain(because it's my motherboard for gaming) that the asrock extreme 4 z97 for example does not support gpu on the x1 slot or riser used for gpu, due to a pin issue on the slot x1
you need the asrock h81 pro btc or somethign else that is used for these things
i know for certain(because it's my motherboard for gaming) that the asrock extreme 4 z97 for example does not support gpu on the x1 slot or riser used for gpu, due to a pin issue on the slot x1
you need the asrock h81 pro btc or somethign else that is used for these things
its ok when its directly in 16x , but problem is when i try to move it to 1x pci e, does r9 nano works on ribbon raiser ? or ? special raiser ?
Try it without the raiser, if that doesnt work you may have a faulty motherboard or GPU
why motherboard doesnt see my card on pcie 1X ? used standard ribbon raiser
Jump to: