Topic: Raspberry Pi and USB erupters problem (Read 2458 times)
I'm not using raspberry pi for mining but I had a lot of problems with some usb hubs when I tried to set up small home server. At the end D-Link 4 Port did a trick for me and it's stable now. Same as others I recomend you to play with power options, different usb port/hub...
You should try Minepeon, it gives you the choice of cgminer or bfgminer. Just what usb hub did you buy, not all hubs work with the Pi. D-Link and Roswell work for me. I have 16 eruters running on 2 Roswell 10 port hubs and a single D-link 7 port hub.
I have found that running the hubs with a .5 amp headroom they run more consistent, fewer HW errors. I'm getting 5.38 Gh/s from this, it's really not cost effective at $60 a Gh/s.
I have found that running the hubs with a .5 amp headroom they run more consistent, fewer HW errors. I'm getting 5.38 Gh/s from this, it's really not cost effective at $60 a Gh/s.
Hello, I am trying to connect my 5 erupters to my pi to start mining.
I bought a usb hub from ebay, and a 3500mA 5v power supply to ensure power is not an issue.
I follow the instructions on
http://learn.adafruit.com/piminer-raspberry-pi-bitcoin-miner/install-cgminer
but when I connect the first erupter the hub "dissappears" from the pi:
... snip
Power is definetely not an issue, I also tried cutting the red wire on the cable that connects the pi and the hub to ensure the pi is not getting backpower.
You say power is definitely not an issue, but all indications are that it is.I bought a usb hub from ebay, and a 3500mA 5v power supply to ensure power is not an issue.
I follow the instructions on
http://learn.adafruit.com/piminer-raspberry-pi-bitcoin-miner/install-cgminer
but when I connect the first erupter the hub "dissappears" from the pi:
... snip
Power is definetely not an issue, I also tried cutting the red wire on the cable that connects the pi and the hub to ensure the pi is not getting backpower.
What happens when you use the 2500mA supply that came with it and only one erupter?
Other USB port?
May sound stupid buy you just have to try everything
May sound stupid buy you just have to try everything
Do you have your RPi SO updated/upgraded?
Have you tried Minepeon as Zeek_W suggested?
Have you tried Minepeon as Zeek_W suggested?
The hub works ok on windows.
I connected my usb thumb drive on the pi and it also works.
I connected my usb thumb drive on the pi and it also works.
Maybe try chucking Minepeon on another SD card and see if it works if the hub recognises devices.
Does the hub work well under windows?
If you connect other device (keyboard, mouse) does it work?
Are you able to measure if the 5V are still present after the Erupter is connected?
In my setup with Erupters + RPi I found bfgminer more stable... but that's not the issue here
Good luck.
Hello, I am trying to connect my 5 erupters to my pi to start mining.
I bought a usb hub from ebay, and a 3500mA 5v power supply to ensure power is not an issue.
I follow the instructions on
http://learn.adafruit.com/piminer-raspberry-pi-bitcoin-miner/install-cgminer
but when I connect the first erupter the hub "dissappears" from the pi:
Power is definetely not an issue, I also tried cutting the red wire on the cable that connects the pi and the hub to ensure the pi is not getting backpower.
I bought a usb hub from ebay, and a 3500mA 5v power supply to ensure power is not an issue.
I follow the instructions on
http://learn.adafruit.com/piminer-raspberry-pi-bitcoin-miner/install-cgminer
but when I connect the first erupter the hub "dissappears" from the pi:
Code:
pi@bomberb17 ~ $ lsusb
Bus 001 Device 002: ID 0424:9512 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
Bus 001 Device 004: ID 0951:1625 Kingston Technology DataTraveler 101 II
Bus 001 Device 005: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
Bus 001 Device 006: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
***(I connect the first erupter to the hub)***
pi@bomberb17 ~ $ lsusb
Bus 001 Device 002: ID 0424:9512 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
Bus 001 Device 004: ID 0951:1625 Kingston Technology DataTraveler 101 II
pi@bomberb17 ~ $ ls /dev/*USB*
ls: cannot access /dev/*USB*: No such file
Bus 001 Device 002: ID 0424:9512 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
Bus 001 Device 004: ID 0951:1625 Kingston Technology DataTraveler 101 II
Bus 001 Device 005: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
Bus 001 Device 006: ID 1a40:0101 Terminus Technology Inc. 4-Port HUB
***(I connect the first erupter to the hub)***
pi@bomberb17 ~ $ lsusb
Bus 001 Device 002: ID 0424:9512 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
Bus 001 Device 004: ID 0951:1625 Kingston Technology DataTraveler 101 II
pi@bomberb17 ~ $ ls /dev/*USB*
ls: cannot access /dev/*USB*: No such file
Power is definetely not an issue, I also tried cutting the red wire on the cable that connects the pi and the hub to ensure the pi is not getting backpower.
Jump to: