I have ordered one board from hashbuster for testing. Will see how it goes. I doubt I will make back much from these but would be a fun project nonetheless to work with (assuming that I can get it to work)
Topic: Reuse chips from defective BitFurryBoards (Cryptx version) ? (Read 752 times)
I have one, possibly 2 boards, that I would like to pull the chips out because one board I got never hashed more than 14Gh/s, and the 2nd one was fine til the USB port broke and now only hashes a combined 35Gh/s with the 14Gh/s board. (It was fine and went up to ~50Gh/s before the USB broke, and just has continued to be a pain to get hashing since that happened)
You should check out the Wasp Project, they are working on prototypes for 4 different chips including BitFury.
You should check out the Wasp Project, they are working on prototypes for 4 different chips including BitFury.
no solder paste needed just flux there is enough left on chips from old board 
And it is doable with a heat gun i have use that and my ir rework both work fine just need to be careful with heat gun not to blow surrounding caps away
And it is doable with a heat gun i have use that and my ir rework both work fine just need to be careful with heat gun not to blow surrounding caps away
This would make a neat DIY project. I plan to order the boards and give it a go. Any additional last minute advice. And like I said its been a very very long time I've don't any kind of soldering.
Keep some extra flux around, and be patient. It can take a little time for this style of chip to loosen up, expicially if they were made RHoS compliant (the solder for that requires more heat, and releases a little less smoothly.)
no solder paste needed just flux there is enough left on chips from old board
And it is doable with a heat gun i have use that and my ir rework both work fine just need to be careful with heat gun not to blow surrounding caps away
And it is doable with a heat gun i have use that and my ir rework both work fine just need to be careful with heat gun not to blow surrounding caps away
This would make a neat DIY project. I plan to order the boards and give it a go. Any additional last minute advice. And like I said its been a very very long time I've done any kind of soldering.
no solder paste needed just flux there is enough left on chips from old board
And it is doable with a heat gun i have use that and my ir rework both work fine just need to be careful with heat gun not to blow surrounding caps away
And it is doable with a heat gun i have use that and my ir rework both work fine just need to be careful with heat gun not to blow surrounding caps away
Get the pcb without asic from here swop chips job done.
Worked for me
https://bitcointalksearch.org/topic/sellin-stock-hashbuster-asic-miners-293668
Worked for me
https://bitcointalksearch.org/topic/sellin-stock-hashbuster-asic-miners-293668
Thanks. That looks interesting. I am not sure how practical or doable would it be to manually desolder the chips using a heatgun (from the old board) and resolder them on the new board with solder paste+heatgun combo.
** taking into consideration that it has been a very long time since I have used a soldering iron
Get the pcb without asic from here swop chips job done.
Worked for me
https://bitcointalksearch.org/topic/sellin-stock-hashbuster-asic-miners-293668
Worked for me
https://bitcointalksearch.org/topic/sellin-stock-hashbuster-asic-miners-293668
I haven't done any digging around, so I can't offer any details, but... it seems like there should be a bare board to support the bitfury chips around here on the forums somewhere. Since they're QFNs, it would take a little dexterity to remove them, and put them on a new board, but it's not impractical like it would be for a BGA.
You could also look into getting the USb on the 2nd one repaired or replaced somehow; depends on how bad the damage is.
Worst comes to worst, if you can't find a replacement, and you're going to junk them, let me know. I have an interest in poking at a couple of the chips, and wouldn't mind paying for your scrap.
You could also look into getting the USb on the 2nd one repaired or replaced somehow; depends on how bad the damage is.
Worst comes to worst, if you can't find a replacement, and you're going to junk them, let me know. I have an interest in poking at a couple of the chips, and wouldn't mind paying for your scrap.
Hi
I have in possession 2 defective boards. One that refused to boot up upon delivery and another with a ripped USB connector (and defective canbus)
The first board never hashed before but the second board was hashing up until the USB connector issue. And for some reason the canbus does not work on this unit.
I was thinking if it was possible to recycle the Bitfurry ASIC chips from these boards and somehow get them converted to USB miners? Any suggestions or ideas or should I just use them as paper weights?
Thanks
I have in possession 2 defective boards. One that refused to boot up upon delivery and another with a ripped USB connector (and defective canbus)
The first board never hashed before but the second board was hashing up until the USB connector issue. And for some reason the canbus does not work on this unit.
I was thinking if it was possible to recycle the Bitfurry ASIC chips from these boards and somehow get them converted to USB miners? Any suggestions or ideas or should I just use them as paper weights?
Thanks
Jump to: