Hi,
in Chain 1 some of asics failed and need to replace with new asics.
Topic: S17+ only hashing 45th (Read 148 times)
If the miner was running for a while before the heatsink fell off it's likely that a heatsink fell off or the board just got too hot and stuff started sliding. Most of the time it's one of them, heatsink, solder ball somewhere or a resistor is out of place. In a severe case it could be a chip, but you'll be able to determine more once you take the board out and look at it really good.
Hey
I purchased these miners used.
One of the boards is completely missing, so that would explain why Chain[0] isnt detected at all.
However 2 days ago Chain[1] was working but now its not working, from your experience, what is the most common reason for this?
I did transport the miner from one house to another, could it have broken in transport?
I purchased these miners used.
One of the boards is completely missing, so that would explain why Chain[0] isnt detected at all.
However 2 days ago Chain[1] was working but now its not working, from your experience, what is the most common reason for this?
I did transport the miner from one house to another, could it have broken in transport?
Did you replug the cables and the issue occur?
would you mind to try running one hashboard with a known working cable so that we can check if it just a cable issue if not then try to upgrade your firmware to the latest version. Sometimes it can fix this problem by upgrading it to the latest firmware also, check the miner hashboard physically, and maybe a few of the heatsink is loose.
Yes, thats old firmware. Latest would be Jun 02 2020 as per the Bitmain support site.
Another question
Can anybody confirm if my S17+ is running old firmware
Can anybody confirm if my S17+ is running old firmware
Quote
Linux 4.6.0-xilinx-gff8137b-dirty #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
Code:
2022-03-14 09:30:55 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.17, check voltage passed.
2022-03-14 09:30:55 uart.c:72:set_baud: set fpga_baud to 115200
2022-03-14 09:31:06 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 0
2022-03-14 09:31:17 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 1
2022-03-14 09:31:27 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 2
...
2022-03-14 09:31:36 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 3
...
2022-03-14 09:31:51 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 4
...
2022-03-14 09:32:06 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 5
...
2022-03-14 09:32:15 driver-btm-api.c:1155:check_asic_number: Chain 1 only find 0 asic, will power off hash board 1
It looks like chain[1] has a problem and needs repair. Also, chain[0] is not detected at all, is its data cable plugged in?
Hey
I purchased these miners used.
One of the boards is completely missing, so that would explain why Chain[0] isnt detected at all.
However 2 days ago Chain[1] was working but now its not working, from your experience, what is the most common reason for this?
I did transport the miner from one house to another, could it have broken in transport?
I suggest do a firmware upgrade first before you do anything else about hardware.
If the upgrade doesn't work try flashing it through the SD card and if it still does not work then go try to replug all cables including the PSU metal(reattached the metal) and maybe there is a connection problem between them and replug the ribbon cable and clean other terminals with thinner or isopropyl alcohol.
If the upgrade doesn't work try flashing it through the SD card and if it still does not work then go try to replug all cables including the PSU metal(reattached the metal) and maybe there is a connection problem between them and replug the ribbon cable and clean other terminals with thinner or isopropyl alcohol.
I am going to try this now, However now only 1 board is showing in the miner status page, prior to this it was 2.
I hope somehow I havnt broke one.
I suggest do a firmware upgrade first before you do anything else about hardware.
If the upgrade doesn't work try flashing it through the SD card and if it still does not work then go try to replug all cables including the PSU metal(reattached the metal) and maybe there is a connection problem between them and replug the ribbon cable and clean other terminals with thinner or isopropyl alcohol.
If the upgrade doesn't work try flashing it through the SD card and if it still does not work then go try to replug all cables including the PSU metal(reattached the metal) and maybe there is a connection problem between them and replug the ribbon cable and clean other terminals with thinner or isopropyl alcohol.
Code:
2022-03-14 09:30:55 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.17, check voltage passed.
2022-03-14 09:30:55 uart.c:72:set_baud: set fpga_baud to 115200
2022-03-14 09:31:06 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 0
2022-03-14 09:31:17 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 1
2022-03-14 09:31:27 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 2
...
2022-03-14 09:31:36 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 3
...
2022-03-14 09:31:51 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 4
...
2022-03-14 09:32:06 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 5
...
2022-03-14 09:32:15 driver-btm-api.c:1155:check_asic_number: Chain 1 only find 0 asic, will power off hash board 1
It looks like chain[1] has a problem and needs repair. Also, chain[0] is not detected at all, is its data cable plugged in?
can anybody help me identify, here is my kernal log
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc:
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203444K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25932K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12892K (cce6a000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 22/11, WL threshold: 4096, image sequence number: 237714726
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 4102/1163, WL threshold: 4096, image sequence number: 437341943
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BED104AC-5B58-4F21-B7BB-4E8C6129D8F7, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2022-03-14 09:29:26 driver-btm-api.c:741:init_freq_mode: This is scan-user version
2022-03-14 09:29:26 driver-btm-api.c:2413:bitmain_soc_init: opt_multi_version = 1
2022-03-14 09:29:26 driver-btm-api.c:2414:bitmain_soc_init: opt_bitmain_ab = 1
2022-03-14 09:29:26 driver-btm-api.c:2415:bitmain_soc_init: opt_bitmain_work_mode = 0
2022-03-14 09:29:26 driver-btm-api.c:2416:bitmain_soc_init: Miner compile time: Tue Apr 7 14:11:08 CST 2020 type: Antminer S17+
2022-03-14 09:29:26 driver-btm-api.c:2417:bitmain_soc_init: commit version: 0fa7066 2020-04-06 22:14:32, build by: lol 2020-04-07 14:17:53
2022-03-14 09:29:26 driver-btm-api.c:2045:show_sn: len:16, 805c14c42b10481c
2022-03-14 09:29:26 driver-btm-api.c:2423:bitmain_soc_init: show sn return 1
2022-03-14 09:29:26 driver-btm-api.c:2065:handle_sn_for_factory_mode: show sn return 1
2022-03-14 09:29:26 driver-btm-api.c:2103:handle_sn_for_factory_mode: read sn success, 805c14c42b10481c
2022-03-14 09:29:26 fan.c:279:front_fan_power_on: Note: front fan is power on!
2022-03-14 09:29:26 fan.c:291:rear_fan_power_on: Note: rear fan is power on!
2022-03-14 09:29:26 driver-btm-api.c:1276:miner_device_init: Detect 256MB control board of XILINX
2022-03-14 09:29:26 driver-btm-api.c:1217:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2022-03-14 09:29:32 driver-btm-api.c:1201:init_miner_version: miner ID : 805c14c42b10481c
2022-03-14 09:29:32 driver-btm-api.c:1207:init_miner_version: FPGA Version = 0xB023
2022-03-14 09:29:36 driver-btm-api.c:799:get_product_id: product_id[1] = 0
2022-03-14 09:29:36 driver-btm-api.c:799:get_product_id: product_id[2] = 0
2022-03-14 09:29:36 driver-btm-api.c:2196:update_conf_by_power_feedback: Power feedback is disabled
2022-03-14 09:29:36 driver-btm-api.c:2164:get_calibration_voltage: calibration voltage flag is error data.
2022-03-14 09:29:36 driver-btm-api.c:2230:update_conf_by_power_feedback: Note: no calibration voltage, default diff = 0
2022-03-14 09:29:36 frequency.c:1366:adjust_higer_max_vol_table: adjust_higer_max_vol_table, adjust_vol = 0
2022-03-14 09:29:36 thread.c:1066:create_read_nonce_reg_thread: create thread
2022-03-14 09:29:42 driver-btm-api.c:1201:init_miner_version: miner ID : 805c14c42b10481c
2022-03-14 09:29:42 driver-btm-api.c:1207:init_miner_version: FPGA Version = 0xB023
2022-03-14 09:29:45 driver-btm-api.c:799:get_product_id: product_id[1] = 0
2022-03-14 09:29:45 driver-btm-api.c:799:get_product_id: product_id[2] = 0
2022-03-14 09:29:45 driver-btm-api.c:754:_set_project_type: project:0
2022-03-14 09:29:45 driver-btm-api.c:775:_set_project_type: Project type: Antminer S17+
2022-03-14 09:29:45 driver-btm-api.c:786:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2022-03-14 09:29:45 driver-btm-api.c:787:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2022-03-14 09:29:45 driver-btm-api.c:786:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2022-03-14 09:29:45 driver-btm-api.c:787:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2022-03-14 09:29:49 driver-btm-api.c:2334:bitmain_board_init: Fan check passed.
2022-03-14 09:29:50 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2022-03-14 09:29:52 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
2022-03-14 09:29:53 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2022-03-14 09:29:56 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2022-03-14 09:29:56 thread.c:1061:create_pic_heart_beat_thread: create thread
2022-03-14 09:29:56 power_api.c:213:power_init: Power init:
2022-03-14 09:29:56 power_api.c:214:power_init: current_voltage_raw = 0
2022-03-14 09:29:56 power_api.c:215:power_init: highest_voltage_raw = 2100
2022-03-14 09:29:56 power_api.c:216:power_init: working_voltage_raw = 1950
2022-03-14 09:29:56 power_api.c:217:power_init: higher_voltage_raw = 2040
2022-03-14 09:29:56 power_api.c:218:power_init: check_asic_voltage_raw = 2100
2022-03-14 09:29:56 driver-btm-api.c:2344:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2022-03-14 09:29:56 power_api.c:186:power_off: init gpio907
2022-03-14 09:30:28 power_api.c:324:set_to_highest_voltage_by_steps: Set to voltage raw 2100, step by step.
2022-03-14 09:30:53 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:30:54 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.154141
2022-03-14 09:30:55 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.192308
2022-03-14 09:30:55 power_api.c:53:_get_avg_voltage: average_voltage = 21.173224
2022-03-14 09:30:55 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.17, check voltage passed.
2022-03-14 09:30:55 uart.c:72:set_baud: set fpga_baud to 115200
2022-03-14 09:31:06 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 0
2022-03-14 09:31:17 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 1
2022-03-14 09:31:27 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 2
2022-03-14 09:31:27 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2100
chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2022-03-14 09:31:36 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 3
2022-03-14 09:31:36 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2050
2022-03-14 09:31:36 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2050, step by step.
2022-03-14 09:31:39 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:31:42 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.645861
2022-03-14 09:31:43 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.656410
2022-03-14 09:31:43 power_api.c:53:_get_avg_voltage: average_voltage = 20.651136
2022-03-14 09:31:43 power_api.c:71:check_voltage: target_vol = 20.50, actural_vol = 20.65, check voltage passed.
chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2022-03-14 09:31:51 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 4
2022-03-14 09:31:51 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2000
2022-03-14 09:31:51 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2000, step by step.
2022-03-14 09:31:55 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:31:56 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.161784
2022-03-14 09:31:58 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.169231
2022-03-14 09:31:58 power_api.c:53:_get_avg_voltage: average_voltage = 20.165508
2022-03-14 09:31:58 power_api.c:71:check_voltage: target_vol = 20.00, actural_vol = 20.17, check voltage passed.
chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2022-03-14 09:32:06 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 5
2022-03-14 09:32:06 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2100
2022-03-14 09:32:06 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2100, step by step.
2022-03-14 09:32:11 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:32:13 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.127226
2022-03-14 09:32:15 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.140844
2022-03-14 09:32:15 power_api.c:53:_get_avg_voltage: average_voltage = 21.134035
2022-03-14 09:32:15 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.13, check voltage passed.
2022-03-14 09:32:15 driver-btm-api.c:1155:check_asic_number: Chain 1 only find 0 asic, will power off hash board 1
2022-03-14 09:32:16 driver-btm-api.c:1157:check_asic_number: Chain 1 voltage: an0 = 2.822581, an2 2.819355, an6 2.535484.
2022-03-14 09:32:28 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[2]: find 65 asic, times 0
2022-03-14 09:32:30 driver-hash-chip.c:266:set_uart_relay: set uart relay to 0x330003
2022-03-14 09:32:30 driver-btm-api.c:397:set_order_clock: chain[2]: set order clock, stragegy 3
2022-03-14 09:32:31 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
2022-03-14 09:32:31 driver-btm-api.c:1854:check_clock_counter: freq 50 clock_counter_limit 6
2022-03-14 09:32:31 voltage[2] = 1960
2022-03-14 09:32:31 power_api.c:226:set_working_voltage_raw: working_voltage_raw = 1960
2022-03-14 09:32:32 temperature.c:340:calibrate_temp_sensor_one_chain: chain 2 temp sensor NCT218
2022-03-14 09:32:32 uart.c:72:set_baud: set fpga_baud to 12000000
2022-03-14 09:32:33 driver-btm-api.c:264:check_bringup_temp: Bring up temperature is 19
2022-03-14 09:32:33 thread.c:1081:create_check_miner_status_thread: create thread
2022-03-14 09:32:33 thread.c:1071:create_show_miner_status_thread: create thread
2022-03-14 09:32:33 thread.c:1051:create_temperature_monitor_thread: create thread
2022-03-14 09:32:33 freq_tuning.c:183:freq_tuning_get_max_freq: Max freq of tuning is 650
2022-03-14 09:32:33 driver-btm-api.c:1727:send_null_work: [DEBUG] Send null work.
2022-03-14 09:32:33 thread.c:1041:create_asic_status_monitor_thread: create thread
2022-03-14 09:32:33 frequency.c:1019:inc_freq_with_fixed_vco: chain = 255, freq = 540, is_higher_voltage = true
2022-03-14 09:32:53 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2090, step by step.
2022-03-14 09:32:54 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:32:56 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.994877
2022-03-14 09:32:56 power_api.c:53:_get_avg_voltage: average_voltage = 20.994877
2022-03-14 09:32:56 power_api.c:71:check_voltage: target_vol = 20.90, actural_vol = 20.99, check voltage passed.
2022-03-14 09:32:56 frequency.c:1090:inc_asic_diff_freq_by_steps: chain = 2, start = 540, freq_step = 5
2022-03-14 09:33:03 driver-btm-api.c:727:set_timeout: freq = 600, percent = 90, hcn = 44236, timeout = 73
2022-03-14 09:33:03 frequency.c:1338:check_initial_temperature_status: need to set higer voltage,vol_higher:2060,vol_limit:2090
2022-03-14 09:33:03 power_api.c:232:set_higher_voltage_raw: higher_voltage_raw = 2060
2022-03-14 09:33:03 power_api.c:338:set_to_higher_voltage_by_steps: Set to voltage raw 2060, step by step.
2022-03-14 09:33:05 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:33:06 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.678616
2022-03-14 09:33:06 power_api.c:53:_get_avg_voltage: average_voltage = 20.678616
2022-03-14 09:33:06 power_api.c:71:check_voltage: target_vol = 20.60, actural_vol = 20.68, check voltage passed.
2022-03-14 09:33:06 thread.c:1076:create_check_system_status_thread: create thread
2022-03-14 09:33:06 driver-btm-api.c:2577:bitmain_soc_init: Init done!
2022-03-14 09:33:06 driver-btm-api.c:216:set_miner_status: STATUS_INIT
2022-03-14 09:33:11 driver-btm-api.c:216:set_miner_status: STATUS_OKAY
2022-03-14 09:33:12 frequency.c:205:get_ideal_hash_rate_GH: ideal_hash_rate = 24189
2022-03-14 09:33:12 frequency.c:223:get_sale_hash_rate_GH: sale_hash_rate = 22000
2022-03-14 09:33:16 driver-btm-api.c:1458:dhash_chip_send_job: Version num 1.
2022-03-14 09:33:26 driver-btm-api.c:1458:dhash_chip_send_job: Version num 4.
2022-03-14 09:33:26 driver-btm-api.c:1606:dhash_chip_send_job: stime.tv_sec 1647250406, block_ntime 1647250405
Quote
Booting Linux on physical CPU 0x0
Linux version 4.6.0-xilinx-gff8137b-dirty (lzq@armdev2) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #25 SMP PREEMPT Fri Nov 23 15:30:52 CST 2018
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine model: Xilinx Zynq
cma: Reserved 16 MiB at 0x0e000000
Memory policy: Data cache writealloc
On node 0 totalpages: 61440
free_area_init_node: node 0, pgdat c0b39280, node_mem_map cde10000
Normal zone: 480 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 61440 pages, LIFO batch:15
percpu: Embedded 12 pages/cpu @cddf1000 s19776 r8192 d21184 u49152
pcpu-alloc: s19776 r8192 d21184 u49152 alloc=12*4096
pcpu-alloc:
- 0
- 1
Kernel command line: mem=240M console=ttyPS0,115200 ramdisk_size=33554432 root=/dev/ram rw earlyprintk
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 203444K/245760K available (6345K kernel code, 231K rwdata, 1896K rodata, 1024K init, 223K bss, 25932K reserved, 16384K cma-reserved, 0K highmem)
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xcf800000 - 0xff800000 ( 768 MB)
lowmem : 0xc0000000 - 0xcf000000 ( 240 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc090c424 (9234 kB)
.init : 0xc0a00000 - 0xc0b00000 (1024 kB)
.data : 0xc0b00000 - 0xc0b39fe0 ( 232 kB)
.bss : 0xc0b39fe0 - 0xc0b71c28 ( 224 kB)
Preemptible hierarchical RCU implementation.
Build-time adjustment of leaf fanout to 32.
RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
RCU: Adjusting geometry for rcu_fanout_leaf=32, nr_cpu_ids=2
NR_IRQS:16 nr_irqs:16 16
efuse mapped to cf800000
ps7-slcr mapped to cf802000
L2C: platform modifies aux control register: 0x72360000 -> 0x72760000
L2C: DT/platform modifies aux control register: 0x72360000 -> 0x72760000
L2C-310 erratum 769419 enabled
L2C-310 enabling early BRESP for Cortex-A9
L2C-310 full line of zeros enabled for Cortex-A9
L2C-310 ID prefetch enabled, offset 1 lines
L2C-310 dynamic clock gating enabled, standby mode enabled
L2C-310 cache controller enabled, 8 ways, 512 kB
L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x76760001
zynq_clock_init: clkc starts at cf802100
Zynq clock init
sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 4398046511103ns
clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x4ce07af025, max_idle_ns: 440795209040 ns
Switching to timer-based delay loop, resolution 3ns
clocksource: ttc_clocksource: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 537538477 ns
ps7-ttc #0 at cf80a000, irq=18
Console: colour dummy device 80x30
Calibrating delay loop (skipped), value calculated using timer frequency.. 666.66 BogoMIPS (lpj=3333333)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x100000 - 0x100058
CPU1: failed to boot: -1
Brought up 1 CPUs
SMP: Total of 1 processors activated (666.66 BogoMIPS).
CPU: All CPU(s) started in SVC mode.
devtmpfs: initialized
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
pinctrl core: initialized pinctrl subsystem
NET: Registered protocol family 16
DMA: preallocated 256 KiB pool for atomic coherent allocations
cpuidle: using governor menu
hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
hw-breakpoint: maximum watchpoint size is 4 bytes.
zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xcf880000
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
media: Linux media interface: v0.10
Linux video capture interface: v2.00
pps_core: LinuxPPS API ver. 1 registered
pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
PTP clock support registered
EDAC MC: Ver: 3.0.0
Advanced Linux Sound Architecture Driver Initialized.
clocksource: Switched to clocksource arm_global_timer
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
UDP hash table entries: 256 (order: 1, 8192 bytes)
UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 64
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 12892K (cce6a000 - cdb01000)
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
futex hash table entries: 512 (order: 3, 32768 bytes)
workingset: timestamp_bits=28 max_order=16 bucket_order=0
jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-241330
dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
e0000000.serial: ttyPS0 at MMIO 0xe0000000 (irq = 158, base_baud = 6249999) is a xuartps
console [ttyPS0] enabled
xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to cf86e000
[drm] Initialized drm 1.1.0 20060810
brd: module loaded
loop: module loaded
CAN device driver interface
gpiod_set_value: invalid GPIO
libphy: MACB_mii_bus: probed
macb e000b000.ethernet eth0: Cadence GEM rev 0x00020118 at 0xe000b000 irq 31 (00:0a:35:00:00:00)
Generic PHY e000b000.etherne:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=e000b000.etherne:00, irq=-1)
e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Xilinx Zynq CpuIdle Driver started
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
ledtrig-cpu: registered to indicate activity on CPUs
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
nand: Micron MT29F2G08ABAEAWP
nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
nand: WARNING: pl35x-nand: the ECC used on your system is too weak compared to the one required by the NAND chip
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
6 ofpart partitions found on MTD device pl35x-nand
Creating 6 MTD partitions on "pl35x-nand":
0x000000000000-0x000002800000 : "BOOT.bin-env-dts-kernel"
0x000002800000-0x000004800000 : "ramfs"
0x000004800000-0x000005000000 : "configs"
0x000005000000-0x000006000000 : "reserve"
0x000006000000-0x000008000000 : "ramfs-bak"
0x000008000000-0x000010000000 : "reserve1"
NET: Registered protocol family 10
sit: IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
can: controller area network core (rev 20120528 abi 9)
NET: Registered protocol family 29
can: raw protocol (rev 20120528)
can: broadcast manager protocol (rev 20120528 t)
can: netlink gateway (rev 20130117) max_hops=1
zynq_pm_ioremap: no compatible node found for 'xlnx,zynq-ddrc-a05'
zynq_pm_late_init: Unable to map DDRC IO memory.
Registering SWP/SWPB emulation handler
hctosys: unable to open rtc device (rtc0)
ALSA device list:
No soundcards found.
RAMDISK: gzip image found at block 0
EXT4-fs (ram0): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (ram0): mounted filesystem without journal. Opts: (null)
VFS: Mounted root (ext4 filesystem) on device 1:0.
devtmpfs: mounted
Freeing unused kernel memory: 1024K (c0a00000 - c0b00000)
EXT4-fs (ram0): re-mounted. Opts: block_validity,delalloc,barrier,user_xattr
random: dd urandom read with 0 bits of entropy available
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0: attached mtd2 (name "configs", size 8 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 22/11, WL threshold: 4096, image sequence number: 237714726
ubi0: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 40
ubi0: background thread "ubi_bgt0d" started, PID 708
UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 711
UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "configs"
UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi0:0): FS size: 1396736 bytes (1 MiB, 11 LEBs), journal size 888833 bytes (0 MiB, 5 LEBs)
UBIFS (ubi0:0): reserved for root: 65970 bytes (64 KiB)
UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID FF09433B-E002-4C29-97EC-6220DDC4BB36, small LPT model
ubi1: attaching mtd5
ubi1: scanning is finished
ubi1: attached mtd5 (name "reserve1", size 128 MiB)
ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi1: good PEBs: 1020, bad PEBs: 4, corrupted PEBs: 0
ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128
ubi1: max/mean erase counter: 4102/1163, WL threshold: 4096, image sequence number: 437341943
ubi1: available PEBs: 0, total reserved PEBs: 1020, PEBs reserved for bad PEB handling: 36
ubi1: background thread "ubi_bgt1d" started, PID 720
UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 723
UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "reserve1"
UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS (ubi1:0): FS size: 123039744 bytes (117 MiB, 969 LEBs), journal size 6221824 bytes (5 MiB, 49 LEBs)
UBIFS (ubi1:0): reserved for root: 4952683 bytes (4836 KiB)
UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID BED104AC-5B58-4F21-B7BB-4E8C6129D8F7, small LPT model
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
macb e000b000.ethernet eth0: unable to generate target frequency: 25000000 Hz
macb e000b000.ethernet eth0: link up (100/Full)
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
In axi fpga driver!
request_mem_region OK!
AXI fpga dev virtual address is 0xcfb38000
*base_vir_addr = 0xb023
In fpga mem driver!
request_mem_region OK!
fpga mem virtual address is 0xd2000000
random: nonblocking pool is initialized
2022-03-14 09:29:26 driver-btm-api.c:741:init_freq_mode: This is scan-user version
2022-03-14 09:29:26 driver-btm-api.c:2413:bitmain_soc_init: opt_multi_version = 1
2022-03-14 09:29:26 driver-btm-api.c:2414:bitmain_soc_init: opt_bitmain_ab = 1
2022-03-14 09:29:26 driver-btm-api.c:2415:bitmain_soc_init: opt_bitmain_work_mode = 0
2022-03-14 09:29:26 driver-btm-api.c:2416:bitmain_soc_init: Miner compile time: Tue Apr 7 14:11:08 CST 2020 type: Antminer S17+
2022-03-14 09:29:26 driver-btm-api.c:2417:bitmain_soc_init: commit version: 0fa7066 2020-04-06 22:14:32, build by: lol 2020-04-07 14:17:53
2022-03-14 09:29:26 driver-btm-api.c:2045:show_sn: len:16, 805c14c42b10481c
2022-03-14 09:29:26 driver-btm-api.c:2423:bitmain_soc_init: show sn return 1
2022-03-14 09:29:26 driver-btm-api.c:2065:handle_sn_for_factory_mode: show sn return 1
2022-03-14 09:29:26 driver-btm-api.c:2103:handle_sn_for_factory_mode: read sn success, 805c14c42b10481c
2022-03-14 09:29:26 fan.c:279:front_fan_power_on: Note: front fan is power on!
2022-03-14 09:29:26 fan.c:291:rear_fan_power_on: Note: rear fan is power on!
2022-03-14 09:29:26 driver-btm-api.c:1276:miner_device_init: Detect 256MB control board of XILINX
2022-03-14 09:29:26 driver-btm-api.c:1217:init_fan_parameter: fan_eft : 0 fan_pwm : 0
2022-03-14 09:29:32 driver-btm-api.c:1201:init_miner_version: miner ID : 805c14c42b10481c
2022-03-14 09:29:32 driver-btm-api.c:1207:init_miner_version: FPGA Version = 0xB023
2022-03-14 09:29:36 driver-btm-api.c:799:get_product_id: product_id[1] = 0
2022-03-14 09:29:36 driver-btm-api.c:799:get_product_id: product_id[2] = 0
2022-03-14 09:29:36 driver-btm-api.c:2196:update_conf_by_power_feedback: Power feedback is disabled
2022-03-14 09:29:36 driver-btm-api.c:2164:get_calibration_voltage: calibration voltage flag is error data.
2022-03-14 09:29:36 driver-btm-api.c:2230:update_conf_by_power_feedback: Note: no calibration voltage, default diff = 0
2022-03-14 09:29:36 frequency.c:1366:adjust_higer_max_vol_table: adjust_higer_max_vol_table, adjust_vol = 0
2022-03-14 09:29:36 thread.c:1066:create_read_nonce_reg_thread: create thread
2022-03-14 09:29:42 driver-btm-api.c:1201:init_miner_version: miner ID : 805c14c42b10481c
2022-03-14 09:29:42 driver-btm-api.c:1207:init_miner_version: FPGA Version = 0xB023
2022-03-14 09:29:45 driver-btm-api.c:799:get_product_id: product_id[1] = 0
2022-03-14 09:29:45 driver-btm-api.c:799:get_product_id: product_id[2] = 0
2022-03-14 09:29:45 driver-btm-api.c:754:_set_project_type: project:0
2022-03-14 09:29:45 driver-btm-api.c:775:_set_project_type: Project type: Antminer S17+
2022-03-14 09:29:45 driver-btm-api.c:786:dump_pcb_bom_version: Chain [1] PCB Version: 0x0100
2022-03-14 09:29:45 driver-btm-api.c:787:dump_pcb_bom_version: Chain [1] BOM Version: 0x0100
2022-03-14 09:29:45 driver-btm-api.c:786:dump_pcb_bom_version: Chain [2] PCB Version: 0x0100
2022-03-14 09:29:45 driver-btm-api.c:787:dump_pcb_bom_version: Chain [2] BOM Version: 0x0100
2022-03-14 09:29:49 driver-btm-api.c:2334:bitmain_board_init: Fan check passed.
2022-03-14 09:29:50 board.c:36:jump_and_app_check_restore_pic: chain[1] PIC jump to app
2022-03-14 09:29:52 board.c:40:jump_and_app_check_restore_pic: Check chain[1] PIC fw version=0x88
2022-03-14 09:29:53 board.c:36:jump_and_app_check_restore_pic: chain[2] PIC jump to app
2022-03-14 09:29:56 board.c:40:jump_and_app_check_restore_pic: Check chain[2] PIC fw version=0x88
2022-03-14 09:29:56 thread.c:1061:create_pic_heart_beat_thread: create thread
2022-03-14 09:29:56 power_api.c:213:power_init: Power init:
2022-03-14 09:29:56 power_api.c:214:power_init: current_voltage_raw = 0
2022-03-14 09:29:56 power_api.c:215:power_init: highest_voltage_raw = 2100
2022-03-14 09:29:56 power_api.c:216:power_init: working_voltage_raw = 1950
2022-03-14 09:29:56 power_api.c:217:power_init: higher_voltage_raw = 2040
2022-03-14 09:29:56 power_api.c:218:power_init: check_asic_voltage_raw = 2100
2022-03-14 09:29:56 driver-btm-api.c:2344:bitmain_board_init: Enter 30s sleep to make sure power release finish.
2022-03-14 09:29:56 power_api.c:186:power_off: init gpio907
2022-03-14 09:30:28 power_api.c:324:set_to_highest_voltage_by_steps: Set to voltage raw 2100, step by step.
2022-03-14 09:30:53 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:30:54 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.154141
2022-03-14 09:30:55 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.192308
2022-03-14 09:30:55 power_api.c:53:_get_avg_voltage: average_voltage = 21.173224
2022-03-14 09:30:55 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.17, check voltage passed.
2022-03-14 09:30:55 uart.c:72:set_baud: set fpga_baud to 115200
2022-03-14 09:31:06 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 0
2022-03-14 09:31:17 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 1
2022-03-14 09:31:27 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 2
2022-03-14 09:31:27 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2100
chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2022-03-14 09:31:36 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 3
2022-03-14 09:31:36 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2050
2022-03-14 09:31:36 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2050, step by step.
2022-03-14 09:31:39 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:31:42 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.645861
2022-03-14 09:31:43 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.656410
2022-03-14 09:31:43 power_api.c:53:_get_avg_voltage: average_voltage = 20.651136
2022-03-14 09:31:43 power_api.c:71:check_voltage: target_vol = 20.50, actural_vol = 20.65, check voltage passed.
chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2022-03-14 09:31:51 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 4
2022-03-14 09:31:51 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2000
2022-03-14 09:31:51 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2000, step by step.
2022-03-14 09:31:55 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:31:56 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 20.161784
2022-03-14 09:31:58 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.169231
2022-03-14 09:31:58 power_api.c:53:_get_avg_voltage: average_voltage = 20.165508
2022-03-14 09:31:58 power_api.c:71:check_voltage: target_vol = 20.00, actural_vol = 20.17, check voltage passed.
chain 1, IO_DRIVE_STRENGTH_CONFIGURATION reg = 0x f1fffff
2022-03-14 09:32:06 driver-btm-api.c:1119:check_asic_number_with_power_on: Chain[1]: find 0 asic, times 5
2022-03-14 09:32:06 power_api.c:380:modify_check_asic_voltage: check_asic_voltage_raw = 2100
2022-03-14 09:32:06 power_api.c:364:set_to_check_asic_voltage_by_steps: Set to voltage raw 2100, step by step.
2022-03-14 09:32:11 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:32:13 power_api.c:40:_get_avg_voltage: chain = 1, voltage = 21.127226
2022-03-14 09:32:15 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 21.140844
2022-03-14 09:32:15 power_api.c:53:_get_avg_voltage: average_voltage = 21.134035
2022-03-14 09:32:15 power_api.c:71:check_voltage: target_vol = 21.00, actural_vol = 21.13, check voltage passed.
2022-03-14 09:32:15 driver-btm-api.c:1155:check_asic_number: Chain 1 only find 0 asic, will power off hash board 1
2022-03-14 09:32:16 driver-btm-api.c:1157:check_asic_number: Chain 1 voltage: an0 = 2.822581, an2 2.819355, an6 2.535484.
2022-03-14 09:32:28 driver-btm-api.c:1096:check_asic_number_with_power_on: Chain[2]: find 65 asic, times 0
2022-03-14 09:32:30 driver-hash-chip.c:266:set_uart_relay: set uart relay to 0x330003
2022-03-14 09:32:30 driver-btm-api.c:397:set_order_clock: chain[2]: set order clock, stragegy 3
2022-03-14 09:32:31 driver-hash-chip.c:502:set_clock_delay_control: core_data = 0x34
2022-03-14 09:32:31 driver-btm-api.c:1854:check_clock_counter: freq 50 clock_counter_limit 6
2022-03-14 09:32:31 voltage[2] = 1960
2022-03-14 09:32:31 power_api.c:226:set_working_voltage_raw: working_voltage_raw = 1960
2022-03-14 09:32:32 temperature.c:340:calibrate_temp_sensor_one_chain: chain 2 temp sensor NCT218
2022-03-14 09:32:32 uart.c:72:set_baud: set fpga_baud to 12000000
2022-03-14 09:32:33 driver-btm-api.c:264:check_bringup_temp: Bring up temperature is 19
2022-03-14 09:32:33 thread.c:1081:create_check_miner_status_thread: create thread
2022-03-14 09:32:33 thread.c:1071:create_show_miner_status_thread: create thread
2022-03-14 09:32:33 thread.c:1051:create_temperature_monitor_thread: create thread
2022-03-14 09:32:33 freq_tuning.c:183:freq_tuning_get_max_freq: Max freq of tuning is 650
2022-03-14 09:32:33 driver-btm-api.c:1727:send_null_work: [DEBUG] Send null work.
2022-03-14 09:32:33 thread.c:1041:create_asic_status_monitor_thread: create thread
2022-03-14 09:32:33 frequency.c:1019:inc_freq_with_fixed_vco: chain = 255, freq = 540, is_higher_voltage = true
2022-03-14 09:32:53 power_api.c:352:set_to_voltage_by_steps: Set to voltage raw 2090, step by step.
2022-03-14 09:32:54 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:32:56 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.994877
2022-03-14 09:32:56 power_api.c:53:_get_avg_voltage: average_voltage = 20.994877
2022-03-14 09:32:56 power_api.c:71:check_voltage: target_vol = 20.90, actural_vol = 20.99, check voltage passed.
2022-03-14 09:32:56 frequency.c:1090:inc_asic_diff_freq_by_steps: chain = 2, start = 540, freq_step = 5
2022-03-14 09:33:03 driver-btm-api.c:727:set_timeout: freq = 600, percent = 90, hcn = 44236, timeout = 73
2022-03-14 09:33:03 frequency.c:1338:check_initial_temperature_status: need to set higer voltage,vol_higher:2060,vol_limit:2090
2022-03-14 09:33:03 power_api.c:232:set_higher_voltage_raw: higher_voltage_raw = 2060
2022-03-14 09:33:03 power_api.c:338:set_to_higher_voltage_by_steps: Set to voltage raw 2060, step by step.
2022-03-14 09:33:05 power_api.c:85:check_voltage_multi: retry time: 0
2022-03-14 09:33:06 power_api.c:40:_get_avg_voltage: chain = 2, voltage = 20.678616
2022-03-14 09:33:06 power_api.c:53:_get_avg_voltage: average_voltage = 20.678616
2022-03-14 09:33:06 power_api.c:71:check_voltage: target_vol = 20.60, actural_vol = 20.68, check voltage passed.
2022-03-14 09:33:06 thread.c:1076:create_check_system_status_thread: create thread
2022-03-14 09:33:06 driver-btm-api.c:2577:bitmain_soc_init: Init done!
2022-03-14 09:33:06 driver-btm-api.c:216:set_miner_status: STATUS_INIT
2022-03-14 09:33:11 driver-btm-api.c:216:set_miner_status: STATUS_OKAY
2022-03-14 09:33:12 frequency.c:205:get_ideal_hash_rate_GH: ideal_hash_rate = 24189
2022-03-14 09:33:12 frequency.c:223:get_sale_hash_rate_GH: sale_hash_rate = 22000
2022-03-14 09:33:16 driver-btm-api.c:1458:dhash_chip_send_job: Version num 1.
2022-03-14 09:33:26 driver-btm-api.c:1458:dhash_chip_send_job: Version num 4.
2022-03-14 09:33:26 driver-btm-api.c:1606:dhash_chip_send_job: stime.tv_sec 1647250406, block_ntime 1647250405
Jump to: